GE Monogram ZIC30GNZAII User manual

monogram.com
Design Guide with
Installation
Instructions
30" Built-In
Bottom-Freezer, 2-Drawer
Refrigerator

Safety Information
BEFORE YOU BEGIN
Read these instructions completely and carefully.
e IM PORTANT — Save these instructions
for local inspector's use. Observe all governing codes
and ordinances.
e Note to Installer — Be sure to leave these
instructions with the Consumer.
e Note to Consumer — Keep these instructions
with your Owner’s Manual for future reference.
Skill Level — installation of this refrigerator requires
basic mechanical, carpentry and plumbing skills. Proper
installation is the responsibility of the installer. Product
failure due to improper installation is not covered uncer
the GE Appliance Warranty. See the Owner's Manual for
warranty information.
For Monogram local service in your area, call
1.800.444.1845.
For Monogram Parts and Accessories, call
1.800.626.2002.
www.monogram.com
A WARNING:
This appliance must be properly grounded.
See “Grounding the Refrigerator,” page 5.
If you received a damaged refrigerator, you should
immediately contact your dealer or builder.
A CAUTION:
Due to the weight and size of this refrigerator, and to
reduce the risk of personal injury or damage to the
product—TWO PEOPLE ARE REQUIRED FOR PROPER
INSTALLATION.
A WARNING:
* These refrigerators are top-heavy and must
be secured to prevent the possibility of tipping
forward. Anti-tip protection is required. See page 14
for details.
« Use this appliance only for its intended purpose.
* Immediately repair or replace electric service cords
that become frayed or damaged.
* Turn off the circuit breaker to disconnect power
before cleaning or making repairs.
e Repairs should be made by a qualified service
technician.
A.WARNING-r600a Refrigerant
Warning: This appliance contains isobutane refrigerant,
R600qa, a natural gas with high environmental
compatibility. However it is also combustible. Please
adhere to the warnings below:
1) When handling, installing and operating the appliance,
care should be taken to avoid
damage to the refrigerant tubing.
2) Servicing shall be performed by factory-authorized service
personnel and component parts shall be replaced with
rnanufacturer-authorized replacement components.
3) Refrigeration products contain refrigerants, which
under federal law must be removed prior
to product disposal.
4} Keep ventilation openings in the appliance enclosures or
in the built-in structure clear of obstruction.
5) Do not use mechanical devices or other means
to accelerate the defrosting process.
6) Do not damage refrigerant circuit.
7) Do not use electrical appliances inside the
food storage compartment of the appliance.
CONTENTS
Design Guide installation Instructions
Cabinet Enclosure
Dimensions
...........
3
Tools,
Hardware,
Materidls
cc
12
Step
14,
Start
Icemaker
oc
20
Refrigerator
Dimensions..............
Step
1,
Rernove
Packaging...
13
The
Installation
Space
ww...
Step
2,
Install
Anti-tio
Bracket............
14
Badge
Templates
cccccccssscccsseneeen
21
Grounding the Refrigerator. Step 3, Thread Water LiN€ wcccce14
Dimensions and Clearances... 3 Step 4, Connect POWER w..sccsscsseesee 14
Integrated Handles Step 5, Remove Toekick and Vent....15
115° DOOF SWING ceeecceceeeeccessseeteeceseeeenteesee 6 Step 6, Slide Unit into Enclosure ......15
integrated Handles Step 7, Connect Water LiN@ wen 15
90°
DOOF
SWING
oer
ees
eee
teeteeeeeeeteeeesessse
7
Step
8,
Level
Refrigerator
.o.cccscsee
16
Professional Handles Step 9, Install Toekick and Vent........16
115° DOOr SWING woes eteececteeneeeee 8 Step 10, Reverse Door Swing......17, 18
Professional
Handles
Step
11,
Adjust
Door
Swing
«0...
18
90°
DOO
SWING
occcssssssseeessccscsesssssneneesceseesss
9
Step
12,
Attach
Hinge
Guard...
18
SS Panel Accessory & Dimension ....10 Step 13, Install Door and Drawer
3/4"
Custom
Panel
Dimensions
........11
POMEIS
caasceccssessesssssssssssssssssesseeeeeee
19

Design Guide
Cabinet Enclosure Dimensions For Fully Integrated Instructions
25” min. depth
30” Finished Width
Height options
80” or * 84"
The cutout depth must be 25"for
flush installations.
* The front face of the refrigerator fits
flush with 25"depth adjacent
cabinets.
* The refrigerator can fit into a 79-1/2"
minimum,
84-1/2" maximum high enclosure.
Although the refrigerator itself can
only be raised to 80 3/8",
* The fresh food door panel can be
constructed to fill additional height:
see page 10.
L!
“O- Design Tip: We recornmend finishing the inside surface of the enclosure a min. of 4” from the front face.
34 3/8"
|
On Design Tip: If using 84” enclosure, consider adding a finished valence above the refrigerator case.
y=
noe Design Tip: It is possible to align your refrigerator drawer with adjacent cabinetry for a completely integrated
= look.

Design Guide
Refrigerator Dimensions with 3/4” Panels
Case
Top with Panels
Door
|
> yee
<— 29 1/2” >
3/4(Case and Door only)
Panel
Height adjustable
from
79-3/8" to 80-3/8" *
1/8"
Clearance
o _
i)
11/4’ lle 4
Side with Panels
ol.
Front with Panels
* The Refrigerator can be adjusted to fit into a cabinet space that is 83-3/8” to 84-
3/8” with the appropriate door panel kit.
Install Clearances
Top Each Side Rear
1/8” / 3mm | 1/4" / 6mm | 1/2” / 12mm

Design Guide
THE INSTALLATION SPACE
Water and Electrical Locations
Electrical and water supply should be located in shaded area only as shown.
PREPARING INSTALL WATER LINE
e A cold water supply is required
for automatic icemaker operation. The water pressure must be
between 40 and 120 psi.
« Route 1/4" OD copper or GE SmartConnect™ plastic tubing between
the house cold water line and the water connection location.
¢ Tubing should be long enough to extend to the front of the
encloasure.
* Water line can enter an opening through the floor or back wall.
¢ Install a shut-off valve between the icernaker water valve and cold
water supply in the home.
NOTE:
* It is recommended that the water shut-off valve be placed in a
location that is easily accessible. We do not advise placing it behind
the unit because of access difficulties. If it is necessary to install the
valve behind the unit, it must be located in the shaded area. 6"
e Saddle type shut-off valves are included in many water supply kits, but are
not recommended for this application.
* The only GE-approved plastic tubing is supplied in the GE
Anti-Tip location. Do
not obstruct this area.
Front view
Install Space
Water and Electrical
Tube Outlet
SmartConnect™ Refrigerator Tubing kits. Do not use any other plastic water supply line because the line is uncer
pressure at all times. Other types of plastic may crack or rupture with age and cause water damage to your home. GE
SmartConnect™ Refrigerator Tubing Kits are available in the following lengths:
6' (1.8 m)
WX08X10006, 15' (4.6 m) WX08X10015 & 25' (7.6 m) WX08X10025
* Commonwealth of Massachusetts Plumbing Codes 248CMR shall be adhered to. Saddle valves are illegal and use is not
permitted in Massachusetts. Consult with your licensed plumber.
Electrical Specifications
* A 115-volt, 60-Hz., 15- or 20-amp power supply is required. An individual properly grounded branch circuit or circuit
breaker is recormmended.
« Install a properly grounded 3-prong electrical receptacle recessed into the back wall. Electrical must be located on rear
wall as shown.
NOTE: GFI (ground fault interrupter} is not recommended.
GROUNDING THE REFRIGERATOR
IMPORTANT—(Please read carefully)
FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE
PROPERLY GROUNDED.
The power cord of this appliance is equipped with
a 3-prong (grounding) plug which mates with a
standard three-prong (grounding) wall receptacle
to minimize the possibility of electric shock hazard
frorn this appliance.
Have the wall outlet and circuit checked by a
qualified electrician to make sure the outlet is
properly grounded.
Where a standard 2-prong wall outlet is encountered, it
is your personal responsibility and obligation to have it
replaced with a properly grounded 3-prong wall outlet.
DO NOT, UNDER ANY
CIRCUMSTANCES, CUT
OR REMOVE THE THIRD
(GROUND) PRONG FROM
THE POWER CORD.
DO NOT USE AN ADAPTER PLUG TO CONNECT THE
REFRIGERATOR TO A 2-PRONG OUTLET.
DO NOT USE AN EXTENSION CORD WITH THIS
APPLIANCE.

Design Guide
Product Clearances
These refrigerators are equipped with a 2-position door
stop. The factory-set 115° door swing can be adjusted to
90° if clearance to adjacent cabinets or walls is restricted.
For 90° Door swing see page 7.
Refrigerator
Allow 15" minimum clearance
for a full 115° door swing.
ttl
SS European or Custom Panels
Top View
115° DOOR SWING
(factory setting)
1-1/4"
1-1/2"
3/4"
1’
1-1/4"
©
Not to scale

Design Guide
ne For a 90° door
swing allow 5” min.
clearance to a wall,
for stainless steel
models.
Refrigerator
«—1/8"
1-3/16" = of gf t
|
1-1/4"
1-1/2”
~eag— 3/4"
we}— 1-1/4"
wa 1-1/2”
SS European or Custom Panels
Top View
90° DOOR SWING
(optional setting)
Not to scale

Design Guide
Product Clearances
These refrigerators are equipped with a 2-position door
stop. The factory-set 115° door swing can be adjusted to
90° if clearance to adjacent cabinets or walls is restricted.
For 90° Door swing see page 9.
Refrigerator | |
-
DS
je Allow 15” minimum clearance
) for a full 115° door swing.
/ \
1-1/8"
2-1/2"
Not to scale
SS Professional Panels
Top View
115° DOOR SWING
(factory setting)

Design Guide
Refrigerator
For a 90° door
swing allow 5” min.
clearance to a wall,
for stainless steel
models.
SS Professional Panels
Top View
90° DOOR SWING
(optional setting)
1-1/4"
2-9/16"
Not to scale

Design Guide
SS PANEL ACCESSORY & DIMENSIONS
3/4"-Thick Solid Door Panel Options
For 80" High Installation
« Integrated - Panel Model ZKST300N LH & RH capable
¢ Professional - Panel Model ZKSP300N LH & RH capable
For 84" High Installation (The door panel is not
reversible for the 84” Installations. A left or right-hand
door panel accessory must be purchased.)
@ LH Integrated - Model ZKST304NLH
@ RH Integrated - Model ZKST304NRH
e LH Professional - Model ZKSP304NLH
® RH Professional - Model ZKSP304NRH
NOTE: Each kit also contains matching freezer and
customizable drawer panels, handles and toekick.
le 29.3/4" +}
Fresh , , .
Food 45-3/8" for 80” installation
49-3/8" for 84” Installation
Cabinets
| ~~ a
Ice Drawer re
—<—<—<4 7 |
Freezer/
Convertible ,
Drawer 2-3/4
4 | |
t
—+ }+——-_ 1/8" Min.*
*There must be a minimum 1/8" gap between panels and
surrounding cabinetry.
Optional Accessory Kits #:
¢ Side-by-Side Installation Kit - ZUG30
* European handle kit - (3 handles} - WR12X10988
(can be purchased through GE Parts)
3/4"-Thick Frame for Glass Door Options
For 80" High Installation
@ Integrated - Model ZKGT300N = LH & RH capable
e Professional - Model ZKGP300N LH & RH capable
For 84" High Installation (The door panel is not
reversible for the 84" Installations. A left or right-hand
door panel accessory must be purchased.)
@ LH Integrated - Model 2KGT304NLH
@ RH Integrated - Model ZKGT304NRH
e LH Professional - Model ZKGP304NLH
e RH Professional - Model ZKGP304NRH
NOTE: Each option also contains matching freezer and
Convertible drawer panels, handles and toekick.
k*—— 29-3/4" ——
rn 8 ol yt
* f
23 Bf to"
go" | 84"
Glass Panel Install. | Install.
for Fresh Food |
45-3/8"
49-3/8"
+
5
| i
3-3/8" —
*Pro style window is slightly smaller.
10