manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. GE
  6. •
  7. Oven
  8. •
  9. GE SCB2000, SCB2001 User manual

GE SCB2000, SCB2001 User manual

• TM
Advantmm
Built-In
Speedcook Ovens
Installation
Instructions
SCB2000, SCB2001
ZSC2000, ZSC2001
Before you begin -- Read these instructions completely and carefully.
IMPORTANT - Save these instructions for local inspector's use.
IMPORTANT - OBSERVE ALL GOVERNING CODES AND ORDINANCES.
Note to Installer - Be sure to leave these instructions with the Consumer:
Note m Consumer - Keep these instructions with your Owners Manual for future reference.
WARNING: This appliance must be properly grounded. See "Electrical Requirements," page 5
If you have a question concerning the installa-
tion of this product, call the GE Answer
Center ®Consumer Information Service at
800.626.2000, 24 hours a day, 7 days a week.
If you received a damaged Oven, you should
immediately contact your dealer or builder:
Proper installation is the responsibility of the
installer. Product failure due to improper
installation is not covered under the GE
Appliance Warranty. See the Owners Manual
for warranty information.
For Monogram local service in your area,
1-800444d845.
For Monogram service in Canada, call
1-888-8804030.
For Monogram Parts and Accessories, call
1-8004126-2002.
• Use this appliance only for its intended
purpose.
CAUTION:
• This oven should be installed by a qualified
installer or service technician.
• Never use the oven for warming or heating a
room. Prolonged use of the oven without
adequate ventilation can be hazardous.
Check with local utilities for electrical codes
that apply in your area. Local codes vary.
Installation electrical connections and
grounding must comply with applicable codes.
In the absence of local codes, the oven should
be installed in accordance with National
Electrical Code ANSI/NFPA 70 or latest
edition.
Contents" Design Information
Product Dimensions ......................................... 3
Advance Planning ............................................ 3
Tools and Materials Required ......................... 3
Cabinetry
Prepare the Opening ....................................... 4
Single Installation ........................................... 4
Installed Above a Single Oven ........................ 4
Installed Above a Warming Drawer ................ 4
Installation Preparation
Electrical Requirements ................................. 5
Install Junction Box ......................................... 5
Installation
Step h Remove Packaging and Parts .............. 6
Step 2: Route Conduit Through Cutout ........ 6
Step 3: Secure Oven to Cabinet ...................... 6
Step 4: Connect Electrical .............................. 7
2
Design Information
Built-In Speedcook Ovens
Product
Dimensions
21-7/8"
15_-27/32" 29-25/32"/r
27/32"4],_
14-I/8"_
4_ :--9/16"
20-27/32" D-,,
___ -27/32" ",
122222::_ ]ZZJ
13. "_r
7/8" 15/32"_r 11/16"
Advance
Planning
•These ovens may be installed directly into a
wall or wall oven cabinetry, 30" minimum
width.
• The fi'ont surface of the oven will be nearly
flush with surrounding cabinetry doors.
• This oven can be installed over any GE/
Monogram single electric buih-in oven or a
single GE/Monogram electric buih-in
warming drawer.
• This oven must be installed at least 36" above
the floor.
IMPORTANT: This oven is not approved
for use above another built-in Speedcook
oven, side by side or under the countertop
installations.
• For personal safety, tbis oven cannot be
installed in a cabinet arrangement such as an
island or peninsula.
• Cabinets installed ac[jacent to wall ovens must
have an adhesion spec of at least 194°F
temperature rating.
• Allow for clearance to adjacent corners, walls,
drawers, etc.
7bols and
Materials
.%qui, d
Tools and Materials Required:
• 2x 4 el 2 x 2 lumber fol runners
•Saw
• Level
• Drill and3/32" bit
• Phillips screwdriver
•Wood screws andadhesiveor other hardware for installing
runnersor shelf to support oven.
Electrical Requirements
•Junction box
•Electrical cable-3-conductoror &conductor wire, as required
by local codes
• ULlisted conduit connector
• Wire cutters and wire stripper
Cabinetry
Built-In Speedcook Ovens
Prepm the
Opening
4
Single Speedcook Installation
- 28-1/2"_
3B3j4M,0
Required
ConstructSolid
130tt0mMie.3/8"
_" Plyw0ed
Supportedby
2x40rlx2
Runners,all
FourSides
Order a 30" wide single oven cabinet or cut
the opening in a wall to dimensions shown.
The rough opening must be:
• Depth - 19" Min.
• Width - 28-1/2" Min.
• Height - 21" Min.
• 36-3/4" fi'om the floor to the cutout is
required.
• These ovens require 3/4" overlap on each
side, top and bottom of the cutout.
• Oven overlaps will conceal cut edges on all
sides of the opening.
When installed over a single oven or a
warming drawe_; allow at least 2" between the
two openings. This separation will provide
clearance fbr bottom overlap of the
Speedcook Oven and top overlap of the
single oven or warming drawer.
• Construct a solid oven floor of 3/8" min.
thick plywood supported by 2 x 4 or 1 x 2
runners on all sides.
• The support must be level and rigidly
mounted, flush with the bottom edge of the
cutout.
For personal safizry,
the mounting surface must be capable of
supporting the cabinet load, in addition
to the added weight of this approximate 100
pound product, plus, additional oven loads
of up to 50 pounds or a total weight of 150
pounds.
Speedcook Oven Installed above a
GE/Monogram Built-In Wall Oven
ConstructSolid
BottomMin.3/8"
Plywood
,Supportedby
2x4orlx2
Runners,all
FourSides
PerOven
*If you are replacing a GE/Monogram electric
double oven with the combined installation
of a Speedcook and single wall oven, use the
dimensions shown. The middle rail
separating the two openings may need to be
larger than the 2" min. shown.
• Always maintain 36-3/4" min. distance fi-om
the floor to the Speedcook oven cutout in
any installation combination.
Speedcook Oven Installed above a
GE/Monogram Warming Drawer
_30" ConstructSolid
BottomMin.3/8"
Plywood
,Supportedby
2x4orlx2
Runners,all
FourSides
21"
36-3/4"Min.
Install2x4
or2x2
Runners or
SolidBottom,
MustSupport
100Ibs.
Noto:Additional clearance between thecutouts may berequired.
Checkto besurethe oven supportsabovethe Warming Drawer
location does not obstructthe required interior 23-1/2" depth and
9-1/4" height See installation instructions for details
When installing the Speedcook oven over
a GE/Monogram electric warming drawe_.
fi_llow the product installation instructions.
• An anti-tip block must be installed at the rear
of the warming drawer opening. Again, see
installation instructions fi_r complete details.
Installation Preparation
Built-In Speedcook Ovens
Elect,Jcal
Requirements
Single Speedcook Installation
Product rating is 120/208 or 120/240 volt, 60
Hz, 30 amps. This product must be connected
to a supply circuit of the proper voltage and
frequency and protected by a time delay fuse
or circuit breaker. The power supply should
be brought to a separate 30 ampere branch
circuit. Wire size must conform to the require-
ments of the National Electric Code or the
prevailing local code.
Combined Speedeook and Wall Oven
Installation:
When installed in combination with a GE/
Monogram single wall oven, use separate
electrical junction boxes,
OR,
Install a single junction box connected to 50
amp. supply circuit or properly rated supply
circuit.
• Refer to single oven installation instructions
for electrical requirements of that product.
• These connections must be made by a
qualified electrician. All electrical
conneclions must meet National Electrical
code or prevailing local codes.
Combined Speedcook and Warming Drawer
installation:
When installing the Speedcook oven over a
GE/Monogram electric warming drawer, a
separate 120V, 60Hz, properly grounded
receptacle must be installed. See instructions
packed with the warming drawer.
Electrical Shock Hazard
•The electrical power to
the oven branch circuit
must be shut offwhile
line connections are
being made.
•Use copper wiring only.
•Electrical ground is
required on this
appliance. The free end
of the green wire (the ground wire) must be
connected to a suitable ground. This wire
must remain grounded to the oven.
• If cold water pipe is interrupted by plastic,
non-metallic gaskets, union connections or
other insulating materials, DO NOT use for
grounding.
• DO NOT ground to a gas pipe.
• DO NOT have a fuse in the NEUTRAL or
GROUNDING circuit. A tuse in the
NEUTRAL or GROUNDING circuit could
result in an electrical shock.
• Check with a qualified electrican if you are
in doubt as to whether the appliance is
properly grounded.
Failure to tollow these instructions could
result in serious it!imy or death.
Install
Junction Box
The conduit is located at the top right on the
back of the oven.
• Locate and install the junction box within
reach of the oven conduit.
- Through the left or right sides of the cabinet
wall and into adjacent cabinet.
- Or, through the cutout floor.
- Or, in the upper cabinet.
Min.
5
Installation
Built-In Speedcook Ovens
Remove
Packaging
and Parts
• Open the door and remove packing material
with ceramic tray.
• Locate owners kit in carton. Remove and
save.
• Locate box with metal trays in carton.
Remove and save.
• Locate parts package containing 5 mounting
screw's. (4 required, 1 extra)
IMPORTANT:To protect the bottom trim, do
not remove the styrofoam shipping base until
the oven is slipped into the opening.
Route
Conduit
Through
Cutout
2 people are required
to lift the oven into the opening. Grasp the
bottom at fi'ont and rear. Discard styrofbam
base. DO NOT USE HANDLE TO LIFT
THE OVEN. DAMAGE WILL OCCUR!
With oven in front of the cabinet opening:
• Insert conduit into cabinet opening.
• Lift the oven into the opening while
continuing to feed the conduit in the
direction of the installed junction box.
Be sure the conduit does not get pinched
between the back of the oven and the
cabinet wall.
J J
ShippingBase
Seo_re
Oven
to Cabinet
• Slide oven into the cabinet opening.
• Drill 3/32" pilot holes into the cabinet frame
through the 4 mounting holes in the oven
fi'ont frame.
• Secure oven to cabinet with screws supplied.
Securely fasten oven to
cabinet using the screws provided. Failure
to do so could cause the oven to move or
tip during use and result in personal it_iury.
ttachment
Screws
SecureOvenTo Cabinet
With ScrewsProvided
6
Installation
Built-In Speedcook Ovens
Connect
Elect Jcal
Electrical Shock Hazard
• Electrical ground is required on the appliance.
• Do not connect the electrical supply until
appliance is permanently grounded.
• Disconnect power to the junction box before
making the electrical connection.
• This appliance must be grounded to a metallic,
permanent wiring system, or a grounding
connector should be connected to the
grounding terminal or wire lead on the appliance.
Failure to do so could result in fire, personal injury or electrical
shock.
3-ConducterBranchCircuit
BranchCircuit
120VAC Red
_ite or
Neutral Gray
120VAC Black
Red
Green
Whffe
Black
4-conductorBranchCircuit
BranchCircuit Oven
120VAC Red Red
120VAC Black Black
Bara or
6reen Green
GNB
Nsutral WhiteorGray White
When connecting to a 3-conductor branch
circuit:
- Connect oven red lead to branch circuit red
lead.
- Connect oven black lead to branch circuit
black lead.
- Connect oven green ground lead and white
lead to branch circuit neutral (white or
gray).
When connecting to a 4-conductor branch
circuit:
-Connect oven red lead to branch circuit red
lead.
- Connect oven black lead to branch circuit
black lead.
- Break connection between oven white lead
and oven green ground lead.
- Connect oven white lead to branch circuit
neutral lead (white or gray).
- Connect oven green ground lead to branch
circuit ground lead (green or bare copper).
Pub, Ne,49-40103 SPECIFICATIONSSUBJECT TO CHANGE WITHOUT NOTICE DWG. NO. 164D3370P101
(N.D. 530) 2/00
Printed in Korea
LG P/N3828W5U0080

Other manuals for SCB2000, SCB2001

3

This manual suits for next models

4

Other GE Oven manuals

GE JTP15 User manual

GE

GE JTP15 User manual

GE Monogram ZET757WD1WW User manual

GE

GE Monogram ZET757WD1WW User manual

GE Monogram Advantium ZSC1000 User manual

GE

GE Monogram Advantium ZSC1000 User manual

GE Monogram ZET1 User manual

GE

GE Monogram ZET1 User manual

GE Monogram ZSC2001FSS User instructions

GE

GE Monogram ZSC2001FSS User instructions

GE JK3000 - 27" User manual

GE

GE JK3000 - 27" User manual

GE Profile PT970SRSS Manual

GE

GE Profile PT970SRSS Manual

GE JTP10GS User manual

GE

GE JTP10GS User manual

GE Profile JT912SKSS Manual

GE

GE Profile JT912SKSS Manual

GE Profile PK916SM Manual

GE

GE Profile PK916SM Manual

GE Profile Advantium PSB2200N User manual

GE

GE Profile Advantium PSB2200N User manual

GE Advantium Series PSA9120 User manual

GE

GE Advantium Series PSA9120 User manual

GE JRS04GP User manual

GE

GE JRS04GP User manual

GE JT1000 User manual

GE

GE JT1000 User manual

GE JKP15 Series User manual

GE

GE JKP15 Series User manual

GE Appliances PT925 How to use

GE

GE Appliances PT925 How to use

GE JKS10 How to use

GE

GE JKS10 How to use

GE JKP70SPSS Manual

GE

GE JKP70SPSS Manual

GE PT7550 User manual

GE

GE PT7550 User manual

GE JTP10GP User manual

GE

GE JTP10GP User manual

GE JTS5000BNTS User manual

GE

GE JTS5000BNTS User manual

GE JKP90SPSS User manual

GE

GE JKP90SPSS User manual

GE JTP50SHSS Manual

GE

GE JTP50SHSS Manual

GE Profile advantium SCB1000 User manual

GE

GE Profile advantium SCB1000 User manual

Popular Oven manuals by other brands

Classique CLFC68SS user manual

Classique

Classique CLFC68SS user manual

DeLonghi DEL604M Installation and service instructions

DeLonghi

DeLonghi DEL604M Installation and service instructions

Zanussi Electrolux ZCG7540 Instruction booklet

Zanussi Electrolux

Zanussi Electrolux ZCG7540 Instruction booklet

Blanco BOSE667X instruction manual

Blanco

Blanco BOSE667X instruction manual

AEG BSK792220M user manual

AEG

AEG BSK792220M user manual

Black & Decker TO1787S use and care manual

Black & Decker

Black & Decker TO1787S use and care manual

AEG BEB231011M user manual

AEG

AEG BEB231011M user manual

Diamond Diverso WR-FD24-MT instruction manual

Diamond

Diamond Diverso WR-FD24-MT instruction manual

Electrolux 790.42003605 Repair parts list

Electrolux

Electrolux 790.42003605 Repair parts list

Panasonic HL-PF685S Operating & installation instructions

Panasonic

Panasonic HL-PF685S Operating & installation instructions

Omega OO654X Operating and installation instructions

Omega

Omega OO654X Operating and installation instructions

Esatto EOP6010TB user manual

Esatto

Esatto EOP6010TB user manual

NEFF C17CR22G0 User manual and installation instructions

NEFF

NEFF C17CR22G0 User manual and installation instructions

Smeg SCV38X Betriebsanleitung

Smeg

Smeg SCV38X Betriebsanleitung

Miele DG6600CS Operating and installation instructions

Miele

Miele DG6600CS Operating and installation instructions

VESTEL VEB34116 user manual

VESTEL

VESTEL VEB34116 user manual

Whirlpool Gold GW395LEP parts manual

Whirlpool

Whirlpool Gold GW395LEP parts manual

Leventi COMBIMAT 10 datasheet

Leventi

Leventi COMBIMAT 10 datasheet

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.