GE RM94903 User manual

Universal
Remote Control
RM94903
INSTRUCTION
MANUAL
94903 Revised Size 1/21/02 1/15/04 8:44 AM Page 1

1
Button Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Setting Up Your Universal Remote . . . . . . . . . . . . . . . .3
Programming Your Universal Remote For:
TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-5
VCR or DVD . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-7
Cable Box or Other Device . . . . . . . . . . . . . . . . . .7-8
Operating A TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Operating A Cable Box . . . . . . . . . . . . . . . . . . . . . . . . . .9
Operating a DVD Player . . . . . . . . . . . . . . . . . . . . . . .10
Operating A VCR . . . . . . . . . . . . . . . . . . . . . . . . . . .10-11
Programming Using Code Search . . . . . . . . . . . . . . . .11
Code Retrieval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Operating A TV/VCR Combo Unit . . . . . . . . . . . . . . .13
Special Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Lost Your Codes? . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Code Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31-35
Table of Contents
94903 Revised Size 1/21/02 1/15/04 8:44 AM Page 2

2
Button Description
Indicator Light
Flashes to show that the
remote is working.
POWER
Operates the same as on
your original remote.
MUTE
Operates the same as on
your original remote.
Device Buttons (TV, VCR/DVD,
CBL/AUX)
The TV, VCR/DVD and CBL/AUX
buttons are used to select the
home entertainment device
you want to control.
VOLUME and CHANNEL
Operate the same as on
your original remote. These
buttons are also used to
enter the code for your
device. The CHANNEL
buttons are also used to
control the SKIP functions
for DVD and CD Players.
VCR Buttons
The REV (Rewind/Reverse),
PLAY, FOR (Fast Forward),
REC (Record), STOP, and
PAUSE buttons control the
same functions as those
found on your VCR remote.
The REV and FOR are also
used to control the
REVERSE and FORWARD
functions for DVD and CD
Players.
94903 Revised Size 1/21/02 1/15/04 8:44 AM Page 3

3
Setting Up Your Universal Remote
Place batteries in the remote
1. Remove the battery compart-
ment cover.
2. Place two AAA batteries as
shown, matching the + and –
end of each battery as indi-
cated in the battery compart-
ment.
3. Replace the cover.
(Some RCA, GE and ProScan devices may already be
pre-programmed. )
1. Press the button of the device
you want to control (for
example TV).
2. If the device turns on, press
another button to confirm
(for example
CHANNEL UP).
3. If the device you selected
(TV) responds, you will not
need to program the remote.
If the device you selected
(TV) does not respond, you
will need to program the
remote.
4. Repeat steps 1-3 for other
devices.
Determine if your remote needs programming
94903 Revised Size 1/21/02 1/15/04 8:44 AM Page 4

4
1. Manually turn on the TV.
2. Find the code for your
brand in the list starting
below.
3. Press and hold the TV but-
ton for five (5) seconds, the
Indicator Light will light up.
4. Release the TV button.
The following buttons
stand for each digit of the
code:
5. Enter the first digit in the
code with the REV button.
Example: if the first num-
ber is 3, depress the REV
button three times. If the
number is 0, do not press
REV and proceed to next
step.
Note: The Indicator Light
will blink after each num-
ber is entered.
6. Enter the second digit in
the code with the PLAY
button the same way as in
step 5. If the number is 0,
do not press PLAY and pro-
ceed to next step.
1st Digit 2nd Digit 3rd Digit
1ST CODE
NUMBER
X
2ND CODE
NUMBER
X
Programming TV Using Code Lists
94903 Revised Size 1/21/02 1/15/04 8:44 AM Page 5

5
3RD CODE
NUMBER
X
TV CODE
7. Enter the third digit in the
code with the FOR button
the same way as in step 5.
If the number is 0, do not
press FOR and proceed to
next step.
8. Press STOP after code is
entered and the Indicator
Light will turn off.
9. With your TV on, press
CHANNEL Up. If the TV
responds, no further
programming is required.
10.Enter your code here for
easy reference.
Programming TV Using Code Lists (con’t)
1. Manually turn on the VCR.
2. Find the code for your
brand in the list starting
below.
3. Press and hold the VCR/DVD
button for five (5) seconds,
the Indicator Light will light
up.
4. Release the VCR/DVD button.
Programming VCR or DVD Player Using
Code Lists
94903 Revised Size 1/21/02 1/15/04 8:44 AM Page 6

6
Programming VCR or DVD Player Using
Code Lists (con’t.)
The following buttons stand
for each digit of the code:
5. Enter the first digit in the
code with the REV button.
Example: if the first number
is 3, depress the REV button
three times. If the number is
0, do not press REV and pro-
ceed to next step.
Note: The Indicator Light
will blink after each number
is entered.
6. Enter the second digit in the
code with the PLAY button
the same way as in step 5. If
the number is 0, do not
press PLAY and proceed to
next step.
7. Enter the third digit in the
code with the FOR button
the same way as in step 5.
If the number is 0, do not
press FOR and proceed to
next step.
8. Press STOP after code is
entered and the Indicator
Light will turn off.
1st Digit 2nd Digit 3rd Digit
1ST CODE
NUMBER
X
2ND CODE
NUMBER
X
3RD CODE
NUMBER
X
94903 Revised Size 1/21/02 1/15/04 8:44 AM Page 7

1. Manually turn on the Cable
Box.
2. Find the code for your brand
in the list starting on the
next page.
3. Press and hold the CBL/AUX
button for five (5) seconds,
the Indicator Light will light
up.
4. Release the CBL/AUX button.
The following buttons stand
for each digit of the code:
5. Enter the first digit in the
code with the REV button.
Example: if the first number
is 3, depress the REV button
three times. If the number is
0, do not press REV and pro-
ceed to next step.
1ST CODE
NUMBER
X
1st Digit 2nd Digit 3rd Digit
VCR/DVD CODE
Programming VCR or DVD Player Using
Code Lists (con’t.)
9. With your VCR or DVD
player on, press CHANNEL
Up. If the VCR or DVD
player responds, no further
programming is required.
10. Enter your code here for
easy reference.
Programming Cable Box Using Code Lists
7
94903 Revised Size 1/21/02 1/15/04 8:44 AM Page 8

8
Note: The Indicator Light will
blink after each number is
entered.
6. Enter the second digit in the
code with the PLAY button
the same way as in step 5.
If the number is 0, do not
press PLAY and proceed to
next step.
7. Enter the third digit in the
code with the FOR button
the same way as in step 5.
If the number is 0, do not
press FOR and proceed to
next step.
8. Press STOP after code is
entered and the Indicator
Light will turn off.
9. With your Cable Box on,
press CHANNEL Up. If the
Cable Box responds, no
further programming is
required.
10. Enter your code here for
easy reference.
Programming Cable Box Using Code Lists
2ND CODE
NUMBER
X
3RD CODE
NUMBER
X
CABLE/ OTHER
DEVICE BOX CODE
94903 Revised Size 1/21/02 1/15/04 8:44 AM Page 9

Turning the TV On and Off.
1.
Press TV to set the remote
to control the TV (most
RCA, GE and ProScan
models will only turn on
when pressing TV not
power).
2. Press POWER to turn the
TV on or off.
Change Channels and Volume on
the TV.
Press VOLUME UP or VOLUME
DOWN to change volume on
the TV.
Press CHANNEL UP or CHAN-
NEL DOWN to change chan-
nels on the TV.
Turning the Cable Box On or
Off.
1. Point the remote at the
cable box and press
CBL/AUXE.
2. Press POWER to turn it on
or off.
Changing Channels on the
Cable Box.
Press CHANNEL UP or CHAN-
NEL DOWN to change chan-
nels on the cable box.
Operating A TV
Operating A Cable Box
9
94903 Revised Size 1/21/02 1/15/04 8:44 AM Page 10

10
Turning the DVD Player On
and Off.
1.
Point the remote at the
DVD player and press
VCR/DVD.
2. Press POWER to turn the
DVD player on or off.
3. Press CHANNEL UP or CHAN-
NEL DOWN for DVD SKIP
functions.
4. Use REV and FOR for DVD
reverse and forward func-
tions.
Operating A DVD Player
Operating A VCR
Turning the VCR On or Off.
1. Press VCR/DVD to set the
remote to control the VCR.
(Most RCA, GE and
ProScan models will only
turn on when pressing
VCR/DVD not POWER. )
2. Press POWER to turn the
VCR
on or off.
Using a tape in your VCR.
1. Turn on the VCR.
2. Insert a tape in the VCR.
3. Press PLAY to start the tape.
Operating A VCR
94903 Revised Size 1/21/02 1/15/04 8:44 AM Page 11

11
Operating A VCROperating A VCR (con’t)
4. Press STOP when you are
finished.
5. Press REW to rewind the
tape.
6. Press PAUSE to pause the
tape.
7. Press RECORD twice to begin
recording.
1. Manually turn on your TV,
VCR or Cable Box.
2. Press the Device button (TV,
VCR/DVD, or CBL/AUX) for five
(5) seconds. The Indicator
Light will go on. Then
release the device button.
3. Press and release POWER
until the device turns off
(you may have to repeat up to
200 times at a rate of
once per second).
4. Press the STOP button.
5. The Indicator Light will go off.
Programming Using Code Search
If your TV, VCR or Cable Box does not respond to your
remote after you have tried all the codes for your brand,
try searching for your code.
Program a device button using Code Search.
94903 Revised Size 1/21/02 1/15/04 8:44 AM Page 12

1. Press the Device button (TV,
VCR/DVD or CBL/AUX) for five
(5) seconds. The Indicator
Light will go on. Then
release the device button.
2. Then press the Device button
(TV, VCR/DVD or CBL/AUX)
again. The Indicator Light will
go off. Release the device
button.
3. For the first digit in the code,
press the REV button and
count the number of blinks.
4. For the second digit in the
code, press the PLAY button
and count the number of
blinks.
5. For the third digit in the
code, press the FOR button
and count the number
of blinks. Note: if there are
no blinks, the number is
zero.
6. Enter your codes here for
reference.
If you need to find the three digit code after you have set
up your remote, use this procedure.
OFF
ON
Code Retrieval
TV CODE
VCR/DVD CODE CABLE/DEVICECODE
12
94903 Revised Size 1/21/02 1/15/04 8:44 AM Page 13

13
Operating A TV/VCR Combo Unit
GE, RCA and ProScan Brand Devices:
Many of these devices (TVs and VCRs) do not
need to be programmed. In the event that
programming is required, the code search
method is suggested.
Note: With these brands, the device button (TV,
VCR) will usually turn the units on. The
OFF/ON button will only turn these devices off.
Low Battery Warning:
When your batteries are weak, the Indicator
Light will blink indicating it is time to change
batteries.
Some TV/VCR combination units may be con-
trolled by using a combination of TV and VCR
codes. For example, the Samsung TV/VCR
combo unit may be controlled by both the
Samsung TV code and the Samsung VCR code.
90 Day Limited Warranty
Jasco Products Company warrants this product to be
free from manufacturing defects for a period of ninety
days from the original date of consumer purchase.
This warranty is limited to the repair or replacement
of this product only and does not extend to conse-
quential or incidental damage to other products that
may be used with this unit. This warranty is in lieu of
all other warranties express or implied. Some states
do not allow limitations on how long an implied war-
ranty lasts or permit the exclusion or limitation of inci-
dental or consequential damages, so the above limita-
tions may not apply to you. This warranty gives you
specific rights, and you may also have other rights
which vary from state to state. If unit should prove
defective within the warranty period, return prepaid
with dated proof of purchase to:
Jasco Products Company
311 N.W. 122nd
Oklahoma City, OK. 73114
94903 Revised Size 1/21/02 1/15/04 8:44 AM Page 14

14
Additional Electronic Products
For additional electronic products, check out our web
site at www.ge-electronics.com.
Lost Your Codes?
Enclosed with this remote is a sticker on
which you should write the codes for each
device you programmed. Apply the sticker
to the back of the remote or somewhere
convenient for future reference.
Also on the sticker is our website address
which, should you lose your codes or pro-
gramming instructions, you can find avail-
able on our website:
www.jascoproducts.com
94903 Revised Size 1/21/02 1/15/04 8:44 AM Page 15

15
Indice
Descripción del botón . . . . . . . . . . . .15-16
Arreglo su telecontrol universal . . . .16-17
Programando su TV telecontrol universal
para:
TV . . . . . . . . . . . . . . . . . . . . . . . .17-19
VCR/DVD . . . . . . . . . . . . . . . . .19-21
El rectángulo del cable/AUX . . . .21-23
Funcionamiento del TV . . . . . . . . . . . .23
Funcionamiento del rectángulo del cable . . .24
Funcionamiento del VCR . . . . . .24-25
Programando su búsqueda del código .26
La extracción del código . . . . . . . . .27
FuncionamientoDeunaUnidadCombodeTV/VCR .28
Operaciones especiales . . . . . . . . . . . . . .28
Garantía . . . . . . . . . . . . . . . . . . . . . . . .29
Perdió sus códigos . . . . . . . . . . . . . . . . .30
Codigo Listas . . . . . . . . . . . . . . . . . . . .31-35
Descripción del botón
MUTE
Funciona igual que en su telecontrol origi-
nal.
LA LUZ DE INDICADOR
Contellea para mostrar que el telecontrol
está funcionando.
POTENCIA
Funciona igual que su telecontrol original
El dispositivo abotona
(TV, VCR/DVD, CBL/AUX)
La TV, CBL/AUX, y los botones del
VCR/DVD se utilizan para seleccionar el
dispositivo casero de la hospitalidad que
usted desea controlar.
94903 Revised Size 1/21/02 1/15/04 8:44 AM Page 16

VOLUME and CHANNEL
Funcione igual que en su telecontrol origi-
nal. Estos botones también se utilizan para
introducir el código para su dispositivo.
Los botones del VCR
Los botones de REV (rebobinado), del
PLAY, del FOR (delantero rápido), de REC
(expediente), STOP, y PAUSE controlan las
mismas funciones que ésas encontradas en
su telecontrol del VCR.
Arreglo su Telecontrol
Universal
Ponga las baterías en el tele-
control:
1. Alejado quitan la cubierta
del compartimiento de
batería.
2. Ponga dos baterías del
AAA según lo mostrado,
corresponder con + y -
extremo de cada batería
según lo indicado en el
compartimiento de batería.
3. Substituya la cubierta.
(Algún RCA, GE y disposi-
tivos de ProScan pueden ser
preprogramados ya)
1. Prensas el botón del dis-
positivo que usted desea
controlar (por ejemplo TV).
16
94903 Revised Size 1/21/02 1/15/04 8:44 AM Page 17

2. Si el dispositivo se gira,
presione otro botón para
confirmar (por ejemplo
canal para arriba).
3. Si el dispositivo que usted
seleccionó (TV) responde,
usted no necesita programar
el telecontrol. Si el disposi-
tivo que usted seleccionó
(TV) no responde, usted
necesita programar el tele-
control.
4. Relance los pasos de pro-
gresión 1-3 para otros dis-
positivos.
1. Gire manualmente la TV.
2. Encuentre el código para
su marca de fábrica en la
lista que comienza abajo.
3. Presione y sostenga el
botón de la TV por cinco (5)
segundos, la luz de indi-
cador se encenderá para
arriba.
Programación del TV usando
Listas De Código
1st Digit 2nd Digit 3rd Digit
17
94903 Revised Size 1/21/02 1/15/04 8:44 AM Page 18

18
4. Versión el botón de la TV.
Los botones siguientes están
parados para cada dígito del
código:
5. Incorpore el primer dígito
en el código con el botón de
REV. Ejemplo: si el primer
número es 3, presione el
botón de REV tres veces. Si
el número es 0, no presione
REV y proceda al paso de
progresión siguiente.
Nota: La luz de indicador
centelleo después de que se
incorpore cada número.
6. Incorpore el segundo dígi-
to en el código con el botón
del PLAY la misma manera
que en el paso de progresión
Si el número es 0, no pre-
sione PLAY y proceda al
paso de progresión sigu-
iente.
7. Incorpore el tercer dígito
en el código con el botón del
FOR la misma manera que
en el paso de progresión 5.
Si el número es 0, no pre-
sione el FOR y proceda al
paso de progresión sigu-
iente.
1ST CODE
NUMBER
X
2ND CODE
NUMBER
X
3RD CODE
NUMBER
X
94903 Revised Size 1/21/02 1/15/04 8:44 AM Page 19

19
8. Presione STOP después
de que se introduzca el
código y la luz de indicador
darán vuelta apagado.
9. Con su TV encendido,
presione CHANNEL para
arriba. Si responde la TV,
se requiere la programación
no adicional.
10. Introducza su código
aquí para la referencia fácil.
1. Gire manualmente el
VCR.
2. Encuentre el código para
su marca de fábrica en la
lista que comienza abajo.
3. Presione y sostenga el
botón del VCR por cinco (5)
segundos, la luz de indi-
cador se encenderá para
arriba.
4. Versión el botón del VCR.
Los botones siguientes
están parados para cada
dígito del código:
Programación su VCR usando
Listas De Código
TV CODE
1st Digit 2nd Digit 3rd Digit
94903 Revised Size 1/21/02 1/15/04 8:44 AM Page 20