GE Monogram ZV30R User manual

30",36"and 48"
Restaurant Style
VentHoods
Modens:
ZV48R
ZV36R
ZV30R
Monogram__
½9 bring go_Jflthings to life,

mnstamiation mnstructions
BEFORE YOU BEGmN
Read these instructions completely and carefully.
®IMPORTANT- S.veth i. .Cti
loc_4im_spector's i_se.
®IMPORTANT- Obse,ve.11governh gcodes
and ordinm]ces.
* Note to Installer- Be sl*re to leave these h]strl*ctions
_]th the Consm))er.
* Note to Consumer - Keep th ese h/sir wtion s flw
hmlre re}brem]ce,
* Skill Level - Installat]o_] of this veto hood reqlx]res
basic mechm]]cal and electrical skills.
* Completion time- ]to 3 horn's,
* Proper im]sta]]ation is the respo_]s]bi]ity o} the his(allen
* Pro(b_ct fhi]m'e (b_e to improper his(alia(loll is m)t
covered raider the Wm'ra(]tv:
Dl(e to the x_eight and size of these vent hoods mid to
red(we the risk ot perso]ia] iqim'yo(" damage to the
product, _I_O PEOPLE ARE REQUIRED FOR
PROPER INSTALIATION.
PRUDENCE
,_ cm(se (b( poids et de ]a tai]]e de ces holies et pore.
reduh'e ]e Hsque de b]essm'es et de dommages, IL FAUT
DEUX PERSONNES POUR FAIRE L'INSTAd_IATION
CORRECTEMEN'E
WARNmNG:
To reduce the risk of fire or electrical shock, do m)t I_se
this ra(]ge hood _it]] rely exteri]a] so(hi-state speed
com]tro] device. Ally sl_ch a]teratiom] h'om original fhctorv
_]rh]g col_]d result h] damage to the m]]t mid/or create
an electrical salbtv hazard.
ADVERTmSSEMENT
Pore" rS(b_]re ]e risque d'h]ce]]die ol_ de choc 5]ectrique,
i] role tm_t pas (_t]]iser cette hotte w,'ec I(m] rSg_]atem" de
\itesse 5]ectrom]]que exteH]e. T(mte modificatiom] de ce
type du branchement d'l_sh]e pel_te e]]dommager
('apparel( ol_ cr&er m] Hsque de choc &]ectriql_e.
TO REDUCE THE RISK OF FIRE, USE ONIX METAd_
DUC_PNORK.
2
TO REDUCE THE RISK OF FIRE, ELECTRICAL
SHOCK OR INJURY TO PERSONS, OBSERVE THE
FOLLOWING:
A. []se this m]]t on(Iv im]the mam]er im]te]]ded bv the
mm] (lfhctm'er. If yola h ave any qlaesti oils, coraltact th e
man U.fh(tu.rer.
g. Befiwe servich]g or c]em_hig mill s_itch po_er offat
the service pro]el amid lock service pane] to prevent
po_ er fl'om be] n g s_i tch ed (m acc] de_] talE. If th e
serSce pmie] camlot be locked, thste]l a tag or
prom h_e_ t wam]n g label to th e pan el.
ADVERT SSEMENT
POUR RItIDUIRE LE RISQUE D'INCENDIE, DE
CHOC f_LECTRIQUE OU DE BLESSURES, IL FAUT
OBSERVER LES REGLES SUIVANTES:
A. [Jti]iser cet apparei] mii(p(eme]]t de ]a man]i&re
prt_vl(e par ]e thb(']cm]t. Ell cas de ql(estio]L co]]sl(]te("
]e eft)ri cm ]t.
g. Axm]t to(tie i_]ter_e_]tio]] o_( nettoyage, co(q0er
]'a]ime_ltatio]] &lectriq_(e a_( db!jo]lctem" et
xerr(mi]]er ]e pa_l]]eaH dH d]sjo]lctel((" [boH(" 1_;iter ]a
raise so_(s tension a(cide]]te]]e. S'i] _]'est pas possible
de ; erro_(i]]er ]e pamlea_( (b( disc(mctem; atta( her
la] p]aca('d ol( line &tiq_(ette t('t_s visible a_( paili/ealL
Fo(" genera] ve]lti]ati_]o i(se on]]'_. Do _]ot i(se to exhm(st
hazard(ms or exph)sh e materials or vapors.
* Str_(ctm'a] fl'ami_]g, i_]sta]]atio_] v, ork mid electrical
_iring m(_st be done b} q_mlilied perso_](s), h]
acco('dm] ce x_i th all appIicab] e codes m]d start dards
inc]udi_]g th'e-rated CO]]StYI(ctio]]_
* %(fliciei]t air is n]eeded t'o]" proper co]]]b_(stio]] mid
exha_(sti_]g of ,gases th('om,h_., the fi_(e (chi]m]e3) of f_(e]
bm'n]i_]g equipment to p('e_ eiit back dralting. Fo]]ox_
the heati_]g ecpdpme_]t mam(fhctm'e(" s guide]i_]e and
saletv stm]dards such as those p_(b]ished by the
Natiom(] Fire Protectiol] Association (NFPA), and the
America_] Society for Heating, RelHgeratio_] and Air
Co]]dilioni_]g E_]gi_]eers (ASHRAE), and the local
code m(thorities.
* Ix)ca( codes vat*. Instal(at(o]] electrical co]]]]ecthms
mid _o('omldi_ig, ira(st comp]} "_ith applicable codes, h]
the absei]ce of local codes, the vent shou.]d be i_]-
sta]] ed i_]ac c ord a_]c e _ai th N at i o__a] El ect('i ca] (i( _de
,AN SI/NFPA 70-1990 or latest editio]].
UTION: ,)re(b(cerisk (,_fire and to
proper]} exhm(st air, be sure to (b(ct air o_aside - Do
not vent exhm(st air imo spa(es within walls or cei]i_gs
o]" i_]to attics, c]'av,] spaces, or garages.
PR UDE NCEI] fh(_t p('e_]dre soin d'i_]sta]]er
m] conduit vers ]'ext&riem" po_r r&duire ]e risq_e
d'h]ce]]die et po_voir _',_(c_er ]'air correcteme]]t. I] _]e
flint pas _vac_er ]'air correctem e]]t. I] ]] e tm_t pas
&vac(mr ]'air dm] s ]' espace ell Ire ] es patois d' UJ] m m; UJ]
p]ahmd o_ m] grenier, m] espa(e sam(mire o_ m]
garage.

Installation Instructions
Product Dimensions ......................................................... 3
Installation Clem'm_res ..................................................... 4
Optional Duct Co_er Accessories .................................... 4
A&_mce Plmming ............................................................. ,5
Po_ er Supply .................................................................... 5
Duct Fitth_Zs ...................................................................... 6
Using Duct Cover Accessories .......................................... 7
Tools an_d MateNMs Requii_d .......................................... 8
Remo _,e the packazi_ Z ..................................................... 8
Pm'ts Provided ................................................................... 9
Step l, Determine Durtwork m_d Wiling Lormions .... ]i0
Step 2A, Install Hood Onto Wall ....................
Step 2B, lnstnll Hood Beneath Soitit ............................ 12
Step B, Com_ect Duct_ork ............................................. IB
Step 4, (:onnert ElertricM .............................................. IB
Step 5, Instal] Duct Covers ............................................. 13
Step 6, hmtal] Motor. ...................................................... 13
Step 7, Instal] Filters ....................................................... 14
Step S, Inst;fl] garkgum'd m_d SheK, .............................. 14
Step 9, Install Shelf ()nl_ ................................................ 15
Step 10, Instal] Imp]eme_t Rods ................................... 15
PRODUCT DIMENSIONS
Warming
Shelf
Each hood is
shipped with a
stainless stee_
backguard ;md a
_nrmh_g shelf.
Hoods may be
installed _Gth the
22-1/F
10_
Mone, or with both
;IS S1_O%11. _7-15/16
Mode[ ZV48R
22-1/2"
Model ZV36R
t
10"
t
Model ZV30R
3

Advance Planning
iNSTALLATiON CLEARANCES
Th ese vem]t hoods m'e des]g]]ed to be im]staN ed on to a
_all (n _bel]eath a soHh o] _cabh]eL
installation with Warming Shelf
• Hoods must be im]staNed 32" Mh],, 38" Max ove_" m]v
ffpe cookh]g mHhce _ hen _ arming shelf is used.
installation without Warming Shelf
• h]staN these hoods 30" Mira to _6" Max. above the
cookh]g suHhce where] h_stalled ovex" any pmfesshmal
style cooktop o_" 1"ai]ge.
• These hoods may be installed 24" mh]. above a gas ox"
electric d_'op-in style cooktop.
Note: Clearances may vary due to type of cooking product and
local codes. Check with local inspectors to be sure standard is
applicable.
Soffit Installation
32"Min.
Max.
Install these hoods 30" Mie. to Allow 32" rain. and 38" max.
36" Max, over a professional clearance above any cooking
style cooktop or range, surface when installed with shelf,
hi this in stal laN o]] the duct_ oH_ _m]]]h]g {_'om the top
of the hood win be con cea]ed im] the sofli t o_" uppe_"
cab]m] et_'v.
Wall MountInstallation
32"Min.
Install these hoods 30"Mie. to Allow 32"rain. and 38" max.
36"Max, over a professional clearance above any cooking
style cooktop or range, surface when installed with shelf.
Fo_" this instaNatiom a decorative duct cove]" is ;_r_d]-
able m conceal the duct_oH_ _'um]ing _rom the top of
the hood. [lse of the duct cove]" _'equi_'es special
consideration to the installatiom_ height abo_e the
COlU/tertt)p.
OPTIONAL DUCT COVER
Decomdve duct cove_'s a_'e available hi 6" am_d ]2"
heights. Duct cove_'s ram' be star ked, hi various
combhlatioi]s, to co]]cea] the duct*_ oH_ 1roll]big Jh'om
the top of die hood m the ceiling.
* Befo_'e you begin_ you should deteH_h]e the im]stalla-
ti on heigh t of th e hood am]d o_'de_" th e coH'ect size
du.ct cove1". The du.ct cove1"s should be o1"de1"ed at the
same Nine as the ve]it hood amid [)e o_1 site be%_'e
hlsta]]aNo]]. ()_'de_" the dl_ct (-ove_" coH'es]._oildhlg to
VOllI _ model.
Duct Cover
12"DuctCover
6" [}ugt Covers
Heed _,_ode_ 6" #oct Cover [}hnensions
ZV48R ZX48DC6 6"H x 19-11/16"W x 11-7/8"D
ZV36R ZXa6DC6 6"H x 15-3/4"W x 11-7/8"D
zVa0R zXagDC6 6"H x 15-3/4"W x 11-7/8"D
12" Duet Covers
Need _ode_ 12" #oct Cover Dimensions
ZV48R ZX48DC12 12"H x 19-11/16"W x 11-7/8"D
ZV36R ZX36DC12 12"H x 15-3/4"W x 11-7/8"D
ZV30R ZXg@O12 12"H x 15-3/4"W x 11-7/8"D
4

Advance Planning
ADVANCE PLANNING
Duetwork Phamfir_g
* These \reilt hoods are equipped for 10" romld
duet',_ork. For best performam]ee, use If}'* rom]d
) _TT
duet_orkon the 48" _Hde hoods. 30"m]do6 hoods
•_TT
* This hood ma} be _,ented \'eTt]c}id])' t]U'Oligh II{p]0eT
eal)hlets_ sol[it o] _ ee]Iim]g. ,5 diet tr;msiti<m piece is
supplied hot xertiea] exhausL [!se ]oeaI]) supplied
e]l)o_,_ s to \relit ]/oi']z(}llta]]} thlXlllgh the rea/K _Aa]].
* Determim]e the exact h)eation oh tile vent hood.
e PIai] tile ]7liKe hOT veilthlg exhiH_st to tile oIKdoo]'s.
* lJse the shortest amid straightest duet route possible.
For satisfhctor)perl'ormam]ee duct rm] shouh]
m_t exceed 150 ft. equha]em]t length for mix duet
*Reher to "DuetFittim]gs',, chart to computetI/e maxi-
mum permissible ]em]gth for duet rm]s to the out-
dooi's.
e [Jse metal duet_ork <mh.
hlstaH a _al] cap or roof cap 1v]th dart/peT _!t tile
exterior openim]g,. Order tile _aI] or rooh cap amid am
trans]t[o]] mleeded ira] advance.
wall Framhng for Adequate Support
* These _em hoods are heavy. Adequate structural
support must be provided. Ho<}ds must be secured t<)
vertical studs ira] the _H_]I
,It is strong b recommend that tile xent hood with
duet cover be on site before {h]a] fi'amim]g amid _r_]]
fhfishim]g. This wiI] also help to accurate]} locate tile
duct_ork :rod electrical service.
Decorative Duet Covers:
Decorative duct covers, 6"" .... " ",rod 12 high, are a_aiIabIe to
fit aI] models. Tile duct cmer com]ceaIs tile duct_ork
rmmimlg from the top of the hood to the eei]im]g or
sohh]t. Stack o]le o]" mo]'e dIwt cove]'s ove]" the top o_
tile hood to reach _our ceiIi_o height
POWER SUPPLY
IMPORTANT- (Please read carefu]]} )
F )ix [ ERS )NAI, SAFET't, THIS A[ [ I,IAN ,E M{JST
_( _ _ ; ( /
BE [k )_ ERi,_ (R)_ NDED,
P(:)[ JR DES P,AISONS
DE SI_CIJRITE, (ZT APPARE]I_ [)(:)IT I_TP,E
( ()P,RE('_TEMENT MIS ,_ iA TEP, RE.
Remme house huse or open eh'euh breaker before
begimfi_g i_sta]]atiom
Do not use a_] extensio]] cord or adapter plug _Hth this
app]ian ce. Fo]]ox_ N ation a] e] ectri ca] codes or [)i'e\'}]!]]-
i_]g local codes mid ordhlanlees.
Electrica_ suppb/
These vent hoods m_st be s_q_plied with ]20V, 6(tHz_
;rod c(mnected to ;m individua]_ properly grom]ded
brm]eh eirodt, mid protected bv a ]5 or 20 amp circ_dt
breaker or time delay h_se.
* Wh'i _]g m _st be 2 _ ire _ ith g]'o m] d.
*If the electrical supply does _]ot meet the above
req_dreme_its_ ca]] a ]iee_]sed e]eetrieia]] be%re
* R o_te h o_se w] r]_]g as c] ose to th e h] stall ati o_]
1ocati(m as p ossi b] e on the back _r_]] _" ceiIi _g.
C.om]eet the _iri_]g to the hol_se wiri_U__hi aceof
d;mce _dth local codes.
Grounding instructions
The gro_mdi,_g conductor m_st be c<mnected to a
gYOIIH d H/e tF_]_ pe1"H/_H] e_] t _A'i I"1_]g s) gt eH/_ {)I" a_] e q_dp-
ment-__9"olmdi_lg termhla] <)i"lead o_/ the hood.
WARNI NG:
the equipme_]t-gro_mding conductor ca_] remit i_] a
risk of e] eetri e sh ock. Ch eek wit h a q ua]ifi ed e] eetrieia_]
or service represe_]tative if vo_ are hi do_bt _hether
the app]ia_ eei s prop er]y groom ded.
ADVERTISSEIVIENT
i,e mam'a[s branchement du fi] de raise 5 ]a terre peut
causer u,_ ehoe 61eetrklue. E,_ eas de dome, co,>ulter
.. a]ec_ic[e, q.a][h]ao... teeh,_[e[e, po._.
d&ermh_er s[ ] apparel] est 5 ]a terre.
5

Advance Planning
DUCT FiTTiNGS
1[!_e this ch_yt to co]_pHte
permissab]e lengths for duct rm_s to
oHtdooys.
Note: Do not exceed maximum penTfissable
equivalent lengths!
Naximum recommended duct
length for these heeds: 150feet
Flexible ducting:
If flexible metal (h_cting is used, a]]
the equivalent {eet ;_]ues in the table
should be doubled. The flexible
metal duct should be straight m_d
smooth and extended as milch as
Do NOT use flexible plastic ducting.
Note: Al_yhomeventilation system,suchasa
v@tilation hood,mayim_terrupttheproperflow of
combustionair andexhaustrequiredbyfireplaces,
gasfurnaces,gaswater heatersand othernaturally
venteds?stemsTominimizethechanceofinterruption
ofsuchnaturallyventedsystems,followthe heating
equipmentmanufacturer'sguidelinesandsafety
staMardssuchasthosepublishedby NFPAandASHRAE
_Hoodsare supplied with a 10"
round transition. A locally
suppiied transition is required
for other sizes.
Note: Outletontop ofhoodis
8-1/8"x8".
*Actual length of straight duct plus duct fitting
equivalent, Equivalent length of duct pieces
are based on actual tests conducted by GE
Evaluation Engineering and reflect require+
ments for good venting performance with
any ventilation hood,
Total Duct Run
6

Advance Planning
USING DUCT COVER ACCESSORIES
To avoid unsightlv gaps, plan the hood installation
height for duct cover use. Use the following formula
to calculate the need for one or more duct covers
and to ensure a trouble free installation.
CeilingHeight
_10" Hood
,_ Height
7r 1r
A=B=C
g_\'e Teco]?? meli d [h _t [h evem] [ h ood am]d decoTa[ive
(]llct cover (if Ilsed) be o]] site beti_re t]m]al f?'amim]g and
_ all finish hlg. Th]s will hel p to accuratdv locat e st uds,
dl_ctwork am]del ecOi cal service.
* Read these examples careflllly to determh]e the need
fk}r oN]e or more (}" or ]12" dllct covers.
A= Countertop to ceiling height,
B = Gap at the top of the hood to the ceiling,
C = Hood installation height =Plus 10" hood height°
NOTE: Dim. C, shollld be betwee]_ 40" and 46" (fl_r a
30" to 36" installation height). Raise oi" ]o_er the hood
in sm]]ati o_1 h eigh t to a]]o_ use of on e <ti"m ore 6" an d
]2** dllct covers.
mNSTALLATION EXAMPLES
8 ft. ceilings: When the hood is installed
32" above the cooking surface and there is
no soffit or upper cabinetry, order one 12"
and one 6" duct cover accessorv.
9ft. ceimings:Whert the hood isinstalled 38"
above the cooking surface, order two 12"duct
cover accessories,
18 ft. ceilings: When the hood is installed
36" above the cooking surface, order three
12" and one 6" duct cover accessories.

mnstalmation Preparation
TOOLS AND MATERIALS REQUIRED
{NOT SUPPUED) 1/4" pivoting
hex socket
Ducttape Wire cutter/stripper
Pencil and tape measure
Spirit level
Metal Snips
Safety glasses
Step ladder Saber saw
or Sawsall
Key Hole Saw
Wire nuts
Flashlight
Electric or battery operated drill
and1/8",3/8"bits
"1 10" round metal
duct, length to
_iJ suit installation.
Phillips and flat
blade
screwdrdivers
Strail_relief for
iunction cover.
120V 60Hz. 15or 20Amp,
2-wire with ground. Properly
grounded branch circuit.
REMOVE THE PACKAGING
• P,emo_,e packages [rom tile "V' shaped cardboard
section. P,emove s]]ippim]g pads.
• i,if't the hood ola of the box.
iMPORTANT: t.e
the <mtside edges of the e×haust opening on the top.
Wood
Mounting
Support
',', /',', Duct ,5
",,,, - Transition--
Hood ,, ", Parts
_ Motor ",,',,
_, Mounted "',"",i
;___i.... 0nSkid.................. ,
* ],ift to remove the grease trays_ Set grease filters mid
trW,s aside for later im/sta]]atior_. D()NOT DI{SCAP,D.
Shipping Carton
* The _e]] t h oo d mott >r is sb ipped se cl _re d to tb e ski d _i tb
4 scre_s, i,ocate mid remo_e 2 screx_s on each side of the
motor. Discard the shippim_g skid and screx_s.
* From the inside of the hood, ]oosel] (do not remove)
the 2 scre_ s h o] di n g the _ ood m om_ ti m_gsupport to
the back of the b oo(i. Rein ove am_d set aside the
motmti_ig s_q_port _ith scre_ s for later h]sta]]atio]].
DO NOT DISCARD,
* Remove tape mid packh_g material f_'om the hood and
a]] s_q_p]ied parts.
8

mnstaliation Preparation
PARTS PROVIDED
],oolite the p_]'ts p_cked "_i th the hood.
Duct Transition
with Damper
Heat Lamp
(2with 48"models}
Allen Wrench
For Implement Rods
2 Stah_lessStee! Grease Filters
(3filters with 48"models)
O000
2 Implement Rods and 4 Stand-offs
Wood Support
with Original Screws
Backguard
oo
Grease Tray
[,oc_.te _ml(] check
com]te]]ts. Sc]'e_k s
2 flat washers
for wall anchors
6(3/16")hollow wall anchors
with screws use 2to secure
hood to ti_ewall atthe bottom,
Use4to secure backguard
andshelf,
10 Phillips head screws.
Use 6to secure hood to the
wood support. (2 are
secured to wood support)
Use 2 to secure 30" and 36"
backguards to wall Use 4 to
secure a 48" backguard.
4 Phillips head screws to
secure the duct transition to
the hood outlet on the top.
2 Phillips head machine
screws to secure shelf to
bottom of hood.
c_ 2shoulder screws
to secure shelf to
bottom of hood. ©
4screws to secure the wood
support to the wall
POZIDRIV3
1 safety screw and loci<
washer, to secure the
blower (screw is marked
with red paint).
9

mnstaJiation mnstructions
ISTEP 11DETERMINE HOOD, DUCTWORK AND WiRiNG LOCATIONS
•Else a level to (h'm_ the cooktop centeHim]e location.
D]'_a the lim]e to ceilim]g height.
• Measm'e desh'ed distm]ce fl'om the bottom of the
hood to the cookh]g sin'{hoe.
Note: If you are installing the hood with duct covers, be sure to read
"Using Duct Dover Accessories" page 7. Exact installation height
may be determined by use of one or more duct covers.
• Dete_l_im/e bottom
of h god ]oc_ti on
(Dimension A) bv
subtn_cth_g ]2-1/2"
f_'om the desi_'ed
installatiom_ h ei_4ht. Installation
Height
Dir A
* Else a level to (h'm_ a st_'aight horizontal pencil line
iN]dicad m_g the bottom of the h god.
* F_'om the ]im]eim] di cad m_g t h e bottom of the h ood_
measm'e 21)" tq_ and dnn_ mmthe_" ]hie fk)_" the loca-
tion of the _ god slq_pox't. See i]] ustx'ation.
TopofHood
20"
Wood
Support 22-1/2"
Bottom of Hood
t
Dimension A
Cooking Surface ,"
©
*House Wiring
Location
*See recessed
location below.
FOR VERTICAL (Straight Up) DUCTING:
* Use a ]eve] to (h'm_ a centeHine fl'om the bottom of the
h oo d to c eilim ]_ o_" sol[{i t.
*]{venting out the cei]im]g_ extend the centeHine
fk)_'_a_'d on the ceiling4 (w soi]h.
* i,ocate the centeHim]e of a ] 0-1/2" hole on the cei]h]g
o_" sot]i tbv m easm'i m]g 6" f}'om the _ all.
FOR DUCTING THROUGH REAR WALL:
* Measm'e the supplied duct transition _ith m]) straight
_'m] ]e_]gth of duct use(L plus 90 ° elbo_ height. [)m_
ho]'izonta] line o_] the _a]] h]te]'secth]g the centeHine.
House Wiring Location:
*The j traction box is fastened to the back of the hood
on the Hoht side.
14" for 48" Models
Electrical 8" for 36" Models
Area 5" for 30" Models
* The _'ecessed back side of the h god p_'ovides a ]a_'ge
m'ea f(w the hot_se _qHng to exit the _a]] and be
_'outed to the _'em" km)ckout m_d jm_ctio_] box.
* The location flw the house _HHng depends on the
i_]staH athm h eigh t of the h god an d the _ i(it h of the
hood. See shaded "E]eco'ica] A_'ea" fo_" locations.
* Remove jm]cdon box cove_" a_]d knockout. }h]stall
stmh] _'e]ief.
18-1/16"for 48"Models
/16" for36"Models
9-1/16"for 30"Models
Alternate Knockout Locations {for soffit installation}
If th e hi sm]] ati o_] _'eq ui _'es_ th e.j m] cti o]] b ox cm] be
_'elocated from the back to the top of the h god. Rein ove
!} sc_'e_ s, align box to top k_]ocko_t an d secm'e with
origin;4 sc_'e_ s.
* Remove junction box cove_" a_d knocko_t, h_stal] st_'ai_
_'e]ief.
10

mnstaliation mnstructions
ISTEP .,.lz liNSTALL HOOD ONTO WALL IMPORTANT'. Framingmustbe capabme of
supporting up to 150 lbs.
SKIP THHSSTEP HFINSTALLING BENEATH A SOFFHT
OR CABINET, GO TO STEP 2B.
•Ix)care at least 2',e]'tical studs at the _ood su.ppo]'t.
• (:el]tel . the supplied >,god su.ppoi% lel_t to Hght and
belo_ the 20" m aH_ed lin e.
Bottom
0f--
Hood
install Transition Onto Top of Hood
tMPORTANT: Remove
shipping tape from
:" damper and check that
" ',,, damper moves freely.
i i
\ CenterlJle of
Installation
SpaceI
Support
• Secm'e tile _kgod suppo_'t to 2 o_" mo_'e ve_'tica] smds_
I_sh]g at least 2 ol_ the 4supplied hmg scl'ews.
:{MPORTANT: Sc_'e_ s must pen eta'ate at ]east ]1-] /2"
in to ve_'t] ca] st uds. (}o m] te_'si n k sc_'e_l s in to slq0po_'t.
i
i
Original Mounting
Screws as Shipped
)
Note: The mounting
screws must remain ie
their original shipping
location. These screws
are positioned to engage
the keyhole slots in the
back of the hood.
Duct
Transition
*P]ace the dl_ct transition piece ove_" the hood exhaust
m]d secm'e _ ith 4 sc_'e_ s p_'ovi deal.
* llse duct tape to sea] the com/ectio]]. (:beck to be sm'e
the dam pe_" moves f}'ee]}.
Hang Hood On Wood Support
_'IJft the hood and hohi close to the installation location.
Rome house _qHng th_xmgh tile knockom and imo tile
* Place the hood ove_" the wood suppo_'t. Be sm'e the
mom]th]g sc_'e_ls engage tile kevimie slots hi tile bark of
the hood.
(}heck to be sm'e the h god is ]e_,e] an d ten te_'ed.
30" Benterline of
to Installation
36" _ Space
Test Duct Cover Fit
* Place duct cme]'(s) me]" tile top of tile ]]god to ci/eck
fo_" _,aas. Adj_st tile ]rood up o_" down if necessaF,.
Adjust depth o[ oHgh]al mom/ting sc_'e_ls in _ood
s_qq_o_'t m_til tile}' p_'ot_'ude 1/4" fo_'_la_'d. This 1/4"
gap wiii p_'mide clearance to hang tile hood.
install Bottom Mounting Screws
DHi] ]/8" pi] otho] es i_ to the t_o bottom m om] ti n g
holes. E]]]m'ge the holes i_ thev did not eme_" studs to
3/8". hi se_'t m] ci/o_'s ibm"_lall g_sten e_'s i_]t o bottom
l/o] es. Item ove m]ch oi" sc1"e_ s m]d add f]at _lasi/e1"s
provided. DHve scx'e_ls imo anchox's and tighten.
* hi stall 4 addi ti o_]al sc_'e_ls th _'o_gh ti/e in si de ba_ k of
the hood and in to the _ood suppo_x.
11

mnstaaiation mnstructions
ISTEP 2B] AJtemate Mounting Method
iNSTALL HOOD TO SOFNT OR BENEATH CABINETS
• The 2 x 4 studs must be located as sho_]] im] the chart,
Dim. A. toa_ceptmom]tim]gscre_s.
"A °"g"
Centedine to Stod Hood Width
and Kevhob Slots Atthe Top
ZV48R 23-9/1ff' 47-15/16"
ZV36R 17-9/1ff' 35-1.5/16"
ZV30R 14-9/1if' 29-15/16"
2"
7-1_
Top View
A i Front of Hood
i_ 8_11/8,,
Ti.......i.......,
Back of Hood
• Drill l/_" pilot holes into thesmdsattl/elocatiom]s
sl/o_m] im] tile top _ie_ illl_stratio]/.
mMPORTANT: Soffit framing must be capabme
of supporting up to 150 mbs.
mnstammTransition Onto Top of Hood
IMPO£TANT:Remove
shipping tape from
damper andcheck that
damper movesfreely.
Duct
Transition
• t-qat e the transition piece over the hood exhaust mid
secure _ ith 4 scrm_ s provided.
Use d_ct tape to seal the com]ectioi]. C]/eck to be sm'e
the damper m ores f}'ee]v.
Mount Hood onto Soffit or Cabinet
Note: ][[ mom]ti_]g to the m]derside of a cabi]let _._it]/ a
recessed bottom, i,]sta]] shims to f]]] the -aa,g_"
Push Back
to Wall I1_
Add Shims
IfBottom
IsRecessed
iBack
'Wall
i
Drive mom]ti_]g scre_sinto the studs m]ti] thev
protrude l/4". The l/4" gap _i]] provide clearance to
e_]gage the kev]]o]e slots hi the top of the hood.
Lift hood to insta]]atio_] positiou. Locate h<mse _b'h]g
mldro_te thro_gh thek]]ocko_t ({}'ore the back or
top of the hood).
* I,]ft hood onto mom/ting scre_s. S]ide back again]st
t h e rear ,4a]].
* Tigh ten m o m/ti _]g scre_ s.
][MPORT_T: For additional support and to mini-
mize %bration during operation, the hood must be
secured to the back wall, Use wall anchors to fasten
bottom back of bood to the wall.
12

mnstaliation mnstructions
ISTEP 31CONNECT DUCTWORK
• Install dwt_oH_, making com_ections in di_'ection of
aiH] ou as ill um'ated.
• Secm'e ioim s in ductwoH_ u'ith sheem_etal sc1"eus.
* Wx>_p all dl_ct,jo] m_ts w] th
duct tape {kn"m] aiI'tight seal.
e []se dl_ct tape to seal the
_'];H] _e COm]]]ect]o]].
Reach h]side the Duct Tape
hood amid pl_sh Over Seam
the dampe_" up and Screw
to be sm'e it
moves f}'eeh.
Air Flow
Screw
DuctTape _'
OverTransition
[STEP 41CONNECT ELECTRICAL
Verify that power Js turned off at the source.
WARNING" . H house_iHm_£ is not 2-ui_'e
_ ith a g_'om] d _ i_'e_ a gI'om]d must be p_'ovided by the
h]sta]]en When hol_se _h'h]g is a]m]]imm]_ be sm'e to
use [I i. app_'oved an t]-ox] dm] t corn po m] d am]d a] umi-
mlIH]/-to-coppe_" COrn/]1 ect o1"s.
ATTENTION ,e ,e,a
maison m_'est pas du type 5 deux fi]s avec UJ] fi] de
teH'e_ ]'h]sta]]atem" doit Jh)ml]h" m] ch'cu]t de teH'e.
{)uail d ]es fi] s de ]am ai son sore] t eli a] m_ hi] m_ i]
p_'ei](h'e soh] d m]]]se_" de ]a p_'_te am]t]oxidat]o]]
appmuvSe pro" [/I, et des comli/ectelu's poll1"
1'a1 m_]n] m_-cu]w'e.
,_iRemove B InsertPower
JunctionBox ConduitThru
Cover StrainRelief
andTighten
White
Ground_, /Black
C UseULListed
WireNuts
llse/_]1"e _lllts to coili/ect h/comi_]__{ _2_1"oll_ld to _1"eeil_
_h]te to _h]te mid b]ack to b]ack_
* Push /_r]_'es hlto jmlcthm box a_]d _'ep]a( e coven Be
sm'e _ i_'es m'e not p,]nch ed.
ISTEP 51 INSTALL DUCT COVERS
Note: FoI" easie_" handling, _'emove caYdbomxi h]se_'t
after" fi]m is pee]ed off.
Remove p_'otective film from duct covei's_ If mt¿_'e than
oil e duct cia e_" i s _sed_ secm'e each p] ece togeth e_" _ ith
*P]ace the (h_ct cmei'(s) o_] top o[ the hood.
Flxm_ i_]side the ]]ood_ secm'e the d_ct cove]" to the
top _aith the sma]] Phi]]ips head sc]'e_as s_q.}p]ied _aith
the covei's.
BTEP 61 INSTALL MOTOR
Outlet t
\
Attachment Spring
Slot Clip
* F_'om th e hi side of t h e h ood, s]ip m oto_" hi to th e
attachment slot on the ]eft.
*Rotate motor" upwa_'ds m]ti] it silaps into the sp1"h/g
clip on the Hght,
Secm'e the motor" to the hood _ith the machh]e
sc]'e/_ m]d ]oc k _ ash en (Sc_'e_ is m ai'ked _ ith _'ed
P] I_g con n ecto]" ]_/to the m ()ton
IMPORTANT: Connector ends
are designed to mate only
one way. Match flat and
round connectors as shown.
Attachment
Screw
/
Spring
Clip
13

mnstaiiation mnstructions
{STEP 7]iNSTALL RLTERS
engage the slots in the hood track.
• To _'emo_ e the fi]te_'s, grasp the ]atch_ pu]] the fi]te]"
I_.H_and lift ore.
[STEP 8] INSTALL BACKGUARD AND SHELF Thishoodcan beinstammedwith thewarm-
mNSTALL BACKGUARD:
• Rein ore packagim_g,
• Place backgu;_'d ag_fim]st die bottom of die hood to
I_se as n template. Mmq_ Iq.q0e_" sc_'e_ ]ocati(ms "A
mid "B"
• Remove backgua_'(L
" Drill fore" ]/8" pilot boles at scre_ ]ocadon_s '%"
mid "B'.
• If dH]] did not enter" smds_ em_]m'ge holes to 3/8".
• h]se_'t ;%a]] m]cho_'s imo die e_]]a]'ge(] holes. Remove
ScI'e% S [}'OH) V,{_]] aFIC])OI'S.
• A]ig]] mid secm'e backg_m_'d to ;_a]] _si_ig 2t_a]]
an ch of sc1"e_ s of w(}od sc1"ews in ]ocad on s ",4".
• Fo_" 30" and g6" mode]s_ i_]sm]] 2sc_'e_%s d/_'o_gb
]]o]e ]ocati o_] s "(" at t]]e bottom of t]/e backg{_m'(].
Fo_"48" m ode] s, hi stall 4 sc]'e_ s.
ing shelf and backguard together or with
the warming shemfor backguard amone.
mNSTALL SHELF OVER BACKGUARD:
h]sta]] t_os]]o_](ie_ _scTewsimoho]es"D i_] the
b(_ttom of hood flange leaving 1/8" gap.
* Remove shell packagh]g a_](] p_'otective I_i]m.
* El]gage sho_](ie_" sc_'e;_ s him the keyhole slots hi die
top of the shelf. Slide shelf to;_m'(is die ]eft to lock
hm) place.
* h]sta]] t_o B/4" ]oiig ma(']/h]e sc_'e_ s th_'o_gh the
bottom of die she]fi_]to die bottom ]]ood flm]ge_
1ocati on "E".
* h]sta]] anchor sc_'e_s th_'o_gb the shelf a_]d him the
*,_a]] holes "B'.
* Remove a]] p_'otecdve film.
Mounting
Holesfor
Backguard(A,C)
andShelf(B)
* If i_]sta]]i_]g d_e backgum'd alone, _,VithOU_[ die
shelf, (]_qve sc]'e_a s i_] a]] ]ocati(ms sho_n.
14

mnstamiation mnsttuctions
ISTEP 9] iNSTALL SHELF "ONLY"
.Remove shelf packaging m_d p_'otecti_ e film.
.l[ ]m_stall] ng the sh el_ _1on e_ _ ]th out the ba_kgua_'d_
plate shelf against the bottom of the hood and ma]q_
sci'e_ hole locations "B" on the _a]].
*DIi]] t_o 1/8" pilot holes.
*if d_']]] did not em]te_" studs_ em]]m'ge ]]o]es to B/S".
. []]se1"t _a]] mlc]lo1"s imlto en]m'ged holes. Remove
sc1"ews J_}'om]]wa]] am/c]/oI"s.
.]]]sta]] t_o shoLdde_" sc_'e_s ira]to holes "D" im] the
bot tom of hood fi am_ge] eavi ngl/S" gap.
* El]gage sholdde_" sc_'e_s into the kevho]e slots in t]_e
top of the shelf. Slide shelf to_a_'ds the ]eft to lock
into place.
. []]sta]] t_o }{/4" ]oilg machim]e sc_'e_s t]_'(mgh the
bottom of the shelf into the bottom hood fiange_
]ocati on "E".
i
/B _
Mounting _
Holes - ,_
for Shelf(B) I
1
ISTEP 10i _NSTALL _MPLEMENT
*[Jse a fiat blade sc_'e_d_qve]" to install stand-offs into
the bt)tto_]/ o_ the ]]ood.
*A]igi] imp]emem ]'od to stm]d-offs x_ith the sc1"ex_ hole
to_a]'ds the i_]side o[ the ]/ood. Secm'e the ]'od to the
sta_]d-offs with the s_q_p]ied A]]ei] wI'eilc]]_
* Fo]]o_ the same p_'ocedm'e on the opposite side.
F_NAMZE _NSTALLAT_ON
* h]sta]] the supplied i_][i'm'ed bulb(s)_
* See the ()_]]e]"s Mam_a] fo]" i_]st]'_ctio]]s to test
op e]'ati o_1.
15

Note: While performing installations described in this book,
safety glasses or goggles should be worn,
t4_ M};_zog'l-_tl_/o_'_l _1_,_'_i_ ),_J_l_*_, _'_ll
Webringgoodthingstolife,
Pub.No.49-80152-2
Dwg.No.164D4290P109
(ND762) 5/03
General Electric Company
r.
Louls_ifle KY4022,_
Printed in Italy