GE GFWN1100L Original instructions

GEAppliances.com
49-90392-2 09-11 GE
Washers
Safety Instructions..............2,3
Operating Instructions
ControlPanels ......................4,5
ControlSettings.....................6,7
Features...........................8–10
Loading and Using the Washer ....10,11
CleaningtheWasher..............12–14
Installation Instructions......15–20
PreparingtoInstallYourWasher......15
Rough-In Dimensions.................16
Location of Your Washer .............16
Unpacking Your Washer..............17
DrainRequirements..................18
ElectricalRequirements ..............18
Water Supply Requirements ..........18
InstallingtheWasher..............19,20
ReplacementParts...................20
Troubleshooting Tips .........21–24
Consumer Support
Warranty ............................25
Service Telephone Numbers ..........26
Owner’s Manual &
Installation Instructions
Write the model and serial
numbers here:
Model # _________________
Serial # __________________
<RXFDQ¿QGWKHPRQDODEHORQWKH
side of the washer.
As an ENERGY STAR®partner,
GE has determined that this
product meets the ENERGY STAR®
JXLGHOLQHVIRUHQHUJ\HȻFLHQF\
GFWN1000
GFWN1100
WBVH5200
WBVH5300
WCVH6400
WCVH6800
WHDVH680

 Install or store where it will not be exposed
to temperatures below freezing or exposed
to the weather, which could cause permanent
damage and invalidate the warranty.
 Properly ground washer to conform with all governing
codes and ordinances. Follow details in Installation
Instructions.
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
WARNING! For your safety, the information in this manual must be followed to minimize the risk
of ¿re or e[Slosion, eleFtriFshoFk, or to SreYent SroSerty damaJe, Sersonal inMury or
loss of life.
7he instruFtions in this manual and all other literature inFluded with this washer are
not meant to FoYer eYery Sossible Fondition and situation that may oFFur. *ood, safe
SraFtiFes and Faution MUST be aSSlied when installinJ, oSeratinJand maintaininJ
any aSSlianFe.
WATER HEATER SAFETY
Under certain conditions, hydrogen gas may be produced in a water heater that has not been used for two
weeks
or more. Hydrogen gas can be explosive under these circumstances.
If the hot water has not been used for two weeks or more, prevent the possibility of damage or injury by
turning on all hot water faucets and allowing them to run for several minutes. Do this before using any electrical
appliance which is connected to the hot water system. This simple procedure will allow any built-up hydrogen
JDVWRHVFDSH6LQFHWKHJDVLVÀDPPDEOHGRQRWVPRNHRUXVHDQRSHQÀDPHRUDSSOLDQFHGXULQJWKLVSURFHVV
PROPER INSTALLATION
This washer must be SroSerly installed and loFated in aFFordanFe with the Installation InstruFtions before it is used.
Keep the area underneath and around your
appliances free of combustible materials such as
lint, paper, rags and chemicals.
Do not leave the washer door open. An open door
could entice children to hang on the door or crawl
inside the washer.
Close supervision is necessary if this appliance is
used by or near children. Do not allow children to
play on, with or inside this or any other appliance.
YOUR LAUNDRY AREA
2
Consumer Support Troubleshooting Tips Operating Instructions Safety Instructions
Installation
Instructions

3
Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation
Instructions
Never reach into washer while it is moving.
Wait until the machine has completely stopped
before opening the door.
Do not mix chlorine bleach with ammonia
or acids such as vinegar and/or rust remover.
0L[LQJGLȺHUHQWFKHPLFDOVFDQSURGXFHDWR[LF
gas which may cause death.
Do not wash or dry articles that have been
cleaned in, washed in, soaked in or spotted
with combustible or explosive substances (such
as wax, oil, paint, gasoline, degreasers, dry-
cleaning solvents, kerosene, etc.) which may ignite
or explode. Do not add these substances to the
wash water. Do not use or place these substances
around your washer or dryer during operation.
7KHODXQGU\SURFHVVFDQUHGXFHWKHÀDPH
retardancy of fabrics. To avoid such a result,
carefully follow the garment manufacturer’s
wash and care instructions.
To minimize the possibility of electric shock,
unplug this appliance from the power supply
or disconnect the washer at the building’s
distribution panel by removing the fuse or
VZLWFKLQJRȺWKHFLUFXLWEUHDNHUEHIRUHDWWHPSWLQJ
any maintenance or cleaning. NOTE: Pressing the
power button does NOT disconnect the appliance
from the power supply.
Never attempt to operate this appliance
if it is damaged, malfunctioning, partially
disassembled, or has missing or broken parts,
including a damaged cord or plug.
Do not slam the washer door closed. Do not try
to force the door open when locked (LOCKED
indicator ON). This could result in damage to
the washer.
The washer is equipped with an electrical
overload protector. The motor will stop
if it becomes overheated. The washer will
automatically restart after a cool-down
period of up to 2 hours, if the washer
KDVQRWEHHQPDQXDOO\WXUQHGRȺ
during this time.
WHEN USIN*THE WASHER
7XUQRȺZDWHUIDXFHWVWRUHOLHYHSUHVVXUHRQ
hoses and valves and to minimize leakage if
a break or rupture should occur. Check the
FRQGLWLRQRIWKH¿OOKRVHV*(UHFRPPHQGV
changing the hoses every 5 years.
Before discarding a washer, or removing it
from service, remove the washer door to prevent
children from hiding inside.
Do not attempt to repair or replace any part of
WKLVDSSOLDQFHXQOHVVVSHFL¿FDOO\UHFRPPHQGHG
in this Owner’s Manual, or in published user-repair
instructions that you understand and have the
skills to carry out.
Do not tamper with controls.
WHEN NOT IN USE
READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.
SAVE THESE INSTRUCTIONS
Use this
appliance
only for its
intended
purpose as
described in
this Owner’s
Manual.
GEAppliances.com

About the washer control panel.
4
Find the illustration that Flosely matFhes your model and see the FyFle desFriStions startinJon SaJe for details.
Consumer Support Troubleshooting Tips Operating Instructions Safety Instructions
Installation
Instructions
(On some
models)

5
Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation
Instructions
GEAppliances.com

About the washer control panel.
6
Consumer Support Troubleshooting Tips Operating Instructions Safety Instructions
Installation
Instructions
2
Power
Press to “wake up” the display. If the display is active, press to put the washer into standby mode.
NOTE: PressinJPOWER does not disFonneFt the aSSlianFe from the Sower suSSly.
Wash Cycles
7KHZDVKF\FOHVDUHRSWLPL]HGIRUVSHFL¿FW\SHVRIZDVKORDGV7KHFKDUWEHORZZLOOKHOS\RXPDWFK
the wash setting with the loads. The GentleClean™lifters lightly tumble the clothes into the water and
detergent solution to clean the load.
WHITES For heavily to lightly soiled white cottons, household linens, work and play clothes.
COLORS/NORMAL For heavy to lightly soiled colorfast cottons, household linens, work and play
clothes.
STAIN WASH For heavy soiled colorfast cottons, household linens, work and play clothes.
EASY CARE For wrinkle-free and permanent press items.
(PERMA PRESS)
(some models)
ACTIVE WEAR For active sports, exercise and some casual wear clothes. Fabrics include modern
(some models) WHFKQRORJ\¿QLVKHVDQG¿EHUVVXFKDVVSDQGH[VWUHWFKDQGPLFUR¿EHUV
DELICATES For lingerie and special-care fabrics with light to normal soil. Provides gentle
(some models) tumbling and soak during wash and rinse.
HANDWASH For items labeled hand-washable with light soils. Provides gentle rocking to mimic
the handwashing action.
WASHABLE For the washing of machine washable wool products, provided that they are
WOOLS washed according to the instructions on the garment label. When selecting this
(some models) cycle, you must use a detergent suitable for washing wool.
MY CYCLE Press to use, create or modify custom wash cycles.
(some models)
SPEED WASH For lightly soiled items that are needed in a hurry. Cycle time is approximately
30 minutes, depending on selected options.
DRAIN & SPIN Drain and spin at any time.
RINSE & SPIN To quickly rinse out any items at any time.
(some models)
1

Soil Level
&KDQJLQJWKH62,//(9(/LQFUHDVHVRUGHFUHDVHVWKHZDVKWLPHWRUHPRYHGLȺHUHQWDPRXQWVRIVRLO
To change the SOIL LEVEL, press the SOIL LEVEL button until you have reached the desired setting.
Spin Speed
Changing the SPIN SPEEDFKDQJHVWKH¿QDOVSLQVSHHGRIWKHF\FOHV$OZD\VIROORZWKHIDEULF
manufacturer’s care label when changing the SPIN SPEED.
To change the SPIN SPEED, press the SPIN SPEED button until you have reached the desired setting.
Higher spin speeds are not available on certain cycles, such as Delicates.
Higher spin speeds remove more water from the clothes and will help reduce dry time, but may also
increase the possibility of setting wrinkles on some fabrics.
Wash Temp
Adjust to select the proper water temperature for the wash cycle. The prewash and rinse water is
always cold to help reduce energy usage and reduce setting of stains and wrinkles.
Follow the fabric manufacturer’s care label when selecting the wash temperature.
To change the wash temperature, press the WASH TEMP button until you have reached the desired
setting. The Sanitized wash temperature is not available on certain cycles, such as Delicates.
When selecting the Sanitize wash temperature (on some models), the washer increases the water
temperature to sanitize and kill more than 99% of many common bacteria found in home laundry. The
sanitize wash temperature is only available on Stain Wash and Whites wash cycles. For best results,
select
the heavy soil setting when using the Sanitize wash temperature setting.
127(7KH¿UVWVHFRQGVRIWKHZDVK¿OOLVDOZD\VFROG7KLVIHDWXUHDVVLVWVLQFRQGLWLRQLQJWKHIDEULF
and preventing stains from setting on garments.
START/PAUSE
Press to start a wash cycle. If the washer is running, pressing it once will pause the washer and unlock
the door. Press again to restart the wash cycle.
NOTE: If the washer is paused and the cycle is not restarted within 2 hours, the current wash cycle will
be cancelled.
NOTE: The washer performs automatic system checks after pressing the START EXWWRQ:DWHUZLOOÀRZ
LQVHFRQGVRUOHVV<RXPD\KHDUWKHGRRUORFNDQGXQORFNEHIRUHZDWHUÀRZVWKLVLVQRUPDO
3
4
5
6
7
GEAppliances.com
Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation
Instructions

Consumer Support Troubleshooting Tips Operating Instructions Safety Instructions
Installation
Instructions
About the washer features.
NOTEFeatures may not be aYailable on all washer models.
Prewash (on some models)
Prewash is an extra wash before
the main wash. Use it for heavily soiled
clothes or for clothes with a care label
that recommends prewashing before
ZDVKLQJ%HVXUHWRDGGKLJKHȻFLHQF\
detergent, or the proper wash additive
to the prewash dispenser.
NOTE: When seleFtinJSrewash,
it is reFommended to use Sowder
deterJent in the main wash (deterJent)
FomSartment.
Extra Rinse
Use an extra rinse when additional rinsing
is desired to remove excess dirt and
detergent from soiled loads.
Delay Start (on some models)
You can delay the start of a wash cycle
for 10–18 hours, depending on the model.
Press the DELAY START button to choose
the number of hours you want to delay
the start of the cycle, then press the START
button. The machine will count down and
start automatically at the correct time.
NOTE: If you forJet to fully Flose the door,
a reminder siJnal will beeSremindinJyou
to do so.
NOTE: If you oSen the door when the delay
is FountinJdown, the maFhine will enter
the Sause state. You must Flose the door
and Sress START aJain in order to restart
the Fountdown.
Lock
You can lock the controls to prevent any
selections from being made. Or you can
lock the controls after you have started
a cycle.
Children cannot accidentally start
the washer by touching pads with
this option selected.
To lock the washer, press and hold
the DELAY START button for 3 seconds
(on some models use SIGNAL button).
To unlock the washer controls, press
and hold the DELAY START button for
3 seconds.
The control lock icon on the display will
light up when it is on.
NOTE: The POWER button Fan still be
used when the maFhine is loFked.
H OLD 3 S EC
TO
S TORE
M Y C YCLE
MY CYCLE (on some models)
To save a favorite cycle, set the desired
settings for wash cycle, soil level, spin speed
and wash temp settings and hold down the
MY CYCLE button for 3 seconds. A beep will
sound to indicate the cycle has been saved.
To use your custom cycle, press the
MY CYCLE button before washing a load.
To change the saved cycle, set the desired
settings and hold down the MY CYCLE
button for 3 seconds.
NOTE: When usinJMY CYCLE, wash
oStions Fannot be modi¿ed after the
FyFle has been started.
NOTEIf you FhanJe wash oStions with
MY CYCLE before startinJthe FyFle, the
MY CYCLE liJht will turn off and you will
be returned to the base FyFle.
8
Cycle Signal
Use the SIGNAL button to change
the volume of the end of cycle signal.
Press the button until you reach
the desired volume.
BASKET CLEAN
BasketClean is a cycle that freshens
up the inside of your washer. The cycle
uses bleach or other available washing
machine cleaners and more water to
refresh your washer. Use BasketClean
once every month to reduce odor and
residue buildup inside the washer.
For more information on BasketClean,
refer to the Care and Cleaning section
on page 12.
7
8
9
10
11
12
13

The Dispenser Drawer
Slowly open the dispenser drawer by pulling
it out until it stops.
After adding laundry products, slowly close
the dispenser drawer. Closing the drawer too
quickly could result in early dispensing of the
bleach, fabric softener or detergent.
You may see water in the bleach and fabric
softener compartments at the end of the cycle.
7KLVLVDUHVXOWRIWKHÀXVKLQJVLSKRQLQJDFWLRQ
and is part of the normal operation of the
washer.
The Liquid Bleach Compartment
IMPORTANT: The bleach compartment
position varies by model. Be sure to identify
the correct compartment for bleach before
using.
If desired, measure out the recommended
amount of liquid bleach, not to exceed
1/3 cup (80 ml), and pour into the center
compartment labeled “LIQUID BLEACH”
marked with this symbol .
Do not e[Feed the ma[imum ¿ll line. OYer¿llinJ
Fan Fause early disSensinJof the bleaFh whiFh
Fould result in damaJed Flothes.
NOTE: Do not use Sowdered bleaFh in the
disSenser.
The Detergent Compartment
 Highef¿ciency detergent is required for this
washer. Use the detergent manufacturer’s
recommended amount.
The detergent selection insert must be placed in
WKHGHWHUJHQWFRPSDUWPHQWLQDVSHFL¿FSRVLWLRQ
according to what type of detergent you are
using.
Powder Detergent – Place the insert
in the rear position. The Powder Icons
must line up on center when the
insert is in the powder position.
 Liquid Detergent – You will need to adjust
the insert according to the type of Liquid
Detergent you are using. The Icons on the side
of the detergent compartment must line up on
the center when the insert is in position.
NOTE: Not all models haYe the [ and [
deterJent settinJs. Some haYe only reJular
HE deterJent settinJs. You must reduFe the
amount of deterJent for [ or [ deterJent
Ser bottle instruFtions.
Move the insert by pulling it up and replace
it by sliding it down between either the rear
or front detergent compartment molded rails, as
desired, for powder or liquid detergent.
 Add measured detergent to the front left
detergent compartment of the dispenser
drawer.
 'HWHUJHQWLVÀXVKHGIURPWKHGLVSHQVHU
at the beginning of the wash cycle. Either
powdered or liquid detergent can be used.
 Detergent usage may need to be adjusted for
water temperature, water hardness,
size and soil level of the load. Avoid using too
much detergent in your washer as it can lead
to oversudsing and detergent residue being
left on the clothes.
 Using more detergent than the recommended
quantity can cause residue buildup on your
washer.
The Prewash Compartment (on some models)
 Only use the Prewash Compartment if you
are selecting the Prewash cycle for heavily
soiled clothes. Add measured detergent or
prewash additive to the back left prewash
compartment of the dispenser drawer.
 'HWHUJHQWRUSUHZDVKDGGLWLYHLVÀXVKHG
from the dispenser in the prewash cycle
(if selected).
NOTE: LiTuid deterJent will drain into the
washer drum as it is added.
 Detergent usage may need to be adjusted for
water temperature, water hardness, size and
soil level of the load. Avoid using too much
detergent in your washer as it can lead to
over sudsing and detergent residue being left
on the clothes.
9
GEAppliances.com
Powder Detergent
Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation
Instructions
On some models, the Liquid Bleach
Compartment is in the center.
On some models, the Liquid Bleach
Compartment is on the right.
Normal HE Liquid
Detergent Setting
2X HE Liquid
Detergent Setting
(most common
setting)
3X HE
Liquid
Detergent
Setting
Appearance may vary

Loading and using the washer.
Always follow fabriFmanufaFturer·s Fare label when launderinJ.
Sorting Wash Loads
Preparing Clothes
Colors
Whites
Lights
Darks
Soil
Heavy
Normal
Light
Fabric
Delicates
Easy Care
Sturdy Cottons
Lint
Lint Producers
Lint Collectors
Combine larJe and small items in a load. Load larJe items ¿rst. LarJe items should not be more than
half the total wash load.
WashinJsinJle items is not reFommended. This may Fause an outofbalanFe load. Add one or two
similar items.
Pillows and Fomforters should not be mi[ed with other items. This may Fause an outofbalanFe load.
To aYoid snaJs durinJwashinJ
Close Jarment ziSSers, snaSs, buttons and hooks.
Mend seams, hems, tears.
EmSty all items from SoFkets.
RemoYe nonwashable Jarment aFFessories suFh as ornaments and nonwashable trim materials.
To aYoid tanJlinJ, tie strinJs, draw ties and beltlike materials.
%rush away surfaFe dirt and linttreat sSots and stains.
PromStly wash wet or stained Jarments to ma[imize results.
Mi[Jarments usinJreFommended ma[imum load sizes on SaJe .
Use nylon mesh Jarment baJs to wash small items.
Wash multiSle Jarments at one time for best results.
Sort laundry into loads that can be washed together.
Follow these steps to maximize garment care.
Consumer Support Troubleshooting Tips Operating Instructions Safety Instructions
Installation
Instructions
10
The Fabric Softener Compartment
IMPORTANT: The fabric softener compartment
position varies by model. Be sure to identify
the correct compartment for fabric softener
before using.
If desired, pour the recommended amount
of liquid fabric softener into the compartment
labeled “FABRIC SOFTENER.”
Use only liTuid fabriFsoftener in the disSenser.
Dilute with water to the ma[imum ¿ll line.
Do not e[Feed the ma[imum ¿ll line. OYer¿llinJ
Fan Fause early disSensinJof the fabriFsoftener
whiFh Fould stain Flothes.
NOTE: Do not Sour fabriFsoftener direFtly
on the wash load.
About the washer features.
On some models, the Fabric Softener
Compartment is on the right.
On some models, the Fabric Softener
Compartment is in the center.

Loading the Washer
Wash drum may be fully loaded with loosely added
items. Do not wash fabrics containing Àammable
materials waxescleaning Àuidsetc..
To add items after washer has started, press
START/PAUSE and wait until the door is unlatched.
The washer may take up to 30 seconds to unlock
the door after pressing START/PAUSE depending
on the machine conditions. Do not try to force open
the door when it is locked. After the door unlocks,
open gently. Add items, close the door and press
START/PAUSE to restart.
11
GEAppliances.com
Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation
Instructions
WORKWEAR
4 Jeans
5 Workwear Shirts
5 Workwear Pants
LINENS
2 Bath Sheets
10 Bath Towels/
12 Washcloths
7 Hand Towels/
2 Terrycloth
Bath Mats
OR
2 Flat Queen-Sized
Sheets
2 Fitted
Queen-Sized
Sheets
4 Pillowcases
MIXED LOAD
4 Pillowcases
2 Hand Towels
2 Flat Sheets/
2 Fitted Sheets
2 Bath Towels/
4 Washcloths
OR
6 Shirts (Men’s
or Women’s)
4 Pair Pants
(Khakis
or Twills)
5 T-Shirts
7 Pairs of Boxers
4 Pairs of Shorts
OR
6 T-Shirts
4 Pairs of
Sweatpants
4 Sweatshirts
2 Hoodies
7 Pairs of Socks
DELICATES**
7 Bras
7 Panties
3 Slips
2 Camisoles
4 Nightgowns
SPEED WASH
(2–4 GARMENTS)
2 Casual Wear
Work Shirts
1 Pair Casual Wear
Work Pants
OR
3 Soccer Uniforms
Maximum Loading Sizes*
([FHHGLQJPD[LPXPUHFRPPHQGHGORDGVL]HVPD\DȺHFWFOHDQLQJSHUIRUPDQFHDQGJDUPHQWFDUH
**Using a nylon mesh bag for small items is recommended.

12
Consumer Support Troubleshooting Tips Operating Instructions Safety Instructions
Installation
Instructions
Cleaning the washer.
Cleaning the Interior
of the Washer
To clean the interior of the washer, select
the BasketClean feature on the control
panel. The cycle will use more water,
in addition to bleach, to refresh your
washer.
NOTE: Read the instructions below
completely before starting the
BasketClean cycle.
1. Remove any garments or objects from
the washer and ensure the washer
basket is empty.
2. Open the washer door and pour
one cup or 250 ml of liquid bleach
or other washing machine cleaner
into the basket.
3. Close the door and select the
BasketClean cycle. Push the START
button.
4. When the BasketClean cycle is
working, you will see CLn on the
display. The cycle will complete in
about 90 minutes. Do not interrupt
the cycle.
5. After the cycle is complete, leave
the door open slightly for better
ventilation.
If for any reason the cycle needs to
be interrupted, the door will not open
immediately. Forcing open the door at
WKLVVWDJHPD\FDXVHZDWHUWRÀRRG
The door will open after the water is
drained to a level where it would not
ÀRRGWKHÀRRU
BasketClean may be interrupted
by pressing the START/PAUSE button
in between cycles. A power outage in
the house might also interrupt the cycle.
When the power supply is back, the
BasketClean cycle resumes where it had
stopped. When interrupted, be sure to
run a complete BasketClean cycle before
using the washer. If the POWER button
is pressed during BasketClean, the cycle
will be lost.
IMPORTANT:
Run BasketClean with 1 Cup
(250 ml) of bleach once a month.
After the completion of a BasketClean
cycle, the interior of your washer may
have a bleach smell.
It is recommended to run a light color
load after the BasketClean cycle.
Care and Cleaning
Exterior: ,PPHGLDWHO\ZLSHRȺDQ\VSLOOV:LSHZLWKGDPSFORWK'RQRWKLWVXUIDFHZLWKVKDUSREMHFWV
Moving and Storage: Ask the service technician to remove water from drain pump and hoses.
Do not store the washer where it will be exposed to the weather. When moving the washer,
the tub should be kept stationary by using the shipping bolts removed during installation.
See Installation Instructions in this book. If these parts are not available, they can be ordered
by visiting our Website at GEAppliances.com or by calling 800.GE.CARES.
Long Vacations: %HVXUHWKHZDWHUVXSSO\LVVKXWRȺDWWKHIDXFHWV'UDLQDOOZDWHUIURPWKHKRVHVLIWKH
weather will be below freezing.

Cleaning the Pump Filter
Due to the nature of the front-load washer,
it is sometimes possible for small articles
to pass to the pump. The washer has a
¿OWHUWRFDSWXUHORVWLWHPVVRWKH\DUHQRW
dumped to the drain. To retrieve lost items,
FOHDQRXWWKHSXPS¿OWHU
1. 8VLQJDFRLQRUÀDWVFUHZGULYHU
in the notch on the door, open
the access door.
2. Place a shallow pan or dish under
the pump access door and towels
RQWKHÀRRULQIURQWRIWKHZDVKHUWR
SURWHFWWKHÀRRU,WLVQRUPDOWRFDWFK
DERXWDFXSRIZDWHUZKHQWKH¿OWHU
is removed.
3. Pull down the pour spout.
4. 7XUQWKHSXPS¿OWHUFRXQWHUFORFNZLVH
DQGUHPRYHWKH¿OWHU2SHQVORZO\WR
allow the water to drain.
5. &OHDQWKHGHEULVIURPWKH¿OWHU
6. 5HSODFHWKH¿OWHUDQGWXUQFORFNZLVH
Tighten securely.
7. Flip up the pour spout.
8. Close the access door.
Pour
spout
Pour
spout
Cleaning the Door Gasket
Open the washer door. Using both hands,
press down the door gasket. Remove any
foreign objects if found trapped inside
the gasket. Make sure there is nothing
blocking the holes behind the gasket.
While holding down the door gasket,
inspect the interior gasket by pulling it
GRZQZLWK\RXU¿QJHUV5HPRYHDQ\
foreign objects if found trapped inside
this gasket. Make sure there is nothing
blocking the holes behind the gasket.
:KHQ\RXDUH¿QLVKHGFOHDQLQJ
the door gasket, remove your
hands and the gasket will return
to the operating position.
Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation
Instructions
13
GEAppliances.com
Pump
lter

Dispenser Drawer Area: Detergent and fabric softener may build up
in the dispenser drawer. Residue should be removed once or twice a month.
 5HPRYHWKHGUDZHUE\¿UVWSXOOLQJLWRXWXQWLOLWVWRSV7KHQUHDFKEDFNLQWR
WKHOHIWUHDUFRUQHURIWKHGUDZHUFDYLW\DQGSUHVVGRZQ¿UPO\RQWKHORFN
tab, pulling out the drawer.
Remove the inserts from the bleach and fabric softener compartments and
the detergent insert. Rinse the inserts and the drawer with hot water to
remove traces of accumulated laundry products.
To clean the drawer opening, use a small brush to clean the recess. Remove
all residue from the upper and lower parts of the recess.
Return inserts to the proper compartments. Replace the dispenser drawer.
Lock tab is visible only after drawer
has been pulled out
14
Consumer Support Troubleshooting Tips Operating Instructions Safety Instructions
Installation
Instructions
Cleaning the washer.

Installation Washer
Instructions
If you have any questions, Fall .*E.CARES (..) or visit our Website at: GEAppliances.com
BEFORE YOU BEGIN
Read these instructions completely and carefully.
IMPORTANT – Save these instructions
for local inspector’s use.
IMPORTANT – Observe all governing
codes and ordinances.
 Note to Installer – Be sure to leave these
instructions with the Consumer.
 Note to Consumer – Keep these instructions
for future reference.
 Skill level – Installation of this appliance requires
basic mechanical and electrical skills.
 Completion time – 1-3 hours
 3URSHULQVWDOODWLRQLVWKHUHVSRQVLELOLW\RIWKHLQVWDOOHU
 3URGXFWIDLOXUHGXHWRLPSURSHULQVWDOODWLRQLVQRW
covered under the Warranty.
WARNING
 7KLVDSSOLDQFHPXVWEHSURSHUO\JURXQGHGDQG
installed as described in these Installation Instructions.
 'RQRWLQVWDOORUVWRUHWKHDSSOLDQFHLQDQDUHDZKHUH
it will be exposed to water/weather. See the Location
of Your Washer section.
 NOTE: This appliance must be properly
grounded, and electrical service to the washer
must conform with local codes and ordinances
and the latest edition of the National Electrical
Code, ANSI/NFPA 70.
FOR YOUR SAFETY:
15
TOOLS REQUIRED FOR
WASHER INSTALLATION
1/4” nut driver
3/8” socket with ratchet
3/8” open-end wrench
Adjustable wrench or 7/16” socket with ratchet
Adjustable wrench or 9/16” open-end wrench
Channel-lock adjustable pliers
Carpenter’s level
Water Hoses (2)
PARTS SUPPLIED
Cable Tie
Hose Guide
STACK BRACKET KIT
A stack bracket kit is available at additional cost.
It can be ordered in the United States by visiting
our website at GEAppliances.com or calling 800.
GE.CARES. Order kit #WE25X10018 or GEFLSTACK.

16
Installation Instructions
LOCATION OF YOUR WASHER
Do Not Install the Washer:
1. In an area exposed to dripping water or outside
weather conditions. The ambient temperature should
never be below 60°F (15.6°C) for proper washer
operation.
2. In an area where it will come in contact with curtains
or drapes.
2QFDUSHW7KHÀRRUMUST be a hard surface with
a maximum slope of 1/2” per foot (1.27 cm per
30 cm). To make sure the washer does not vibrate
RUPRYH\RXPD\KDYHWRUHLQIRUFHWKHÀRRU
NOTE: ,IÀRRULVLQSRRUFRQGLWLRQXVHµLPSUHJQDWHG
SO\ZRRGVKHHWVROLGO\DWWDFKHGWRWKHH[LVWLQJÀRRU
covering.
IMPORTANT:
Minimum Installation Clearances
 :KHQLQVWDOOHGLQDOFRYH6LGHV5HDU
Top = 0” (0 cm)
 :KHQLQVWDOOHGLQFORVHW6LGHV5HDU
Top = 0” (0 cm), Front = 1” (2.54 cm)
 &ORVHWGRRUYHQWLODWLRQRSHQLQJVUHTXLUHG
2 louvers each 60 square in. (387 cm), located 3”
(7.6 cm) from top and bottom of door
ROUGH-IN DIMENSIONS
SIDE
FRONT
27.0”
(68.6 cm)
20.4” (51.9 cm)
ELECTRONIC TRANSPARENT VISOR
2.2”
(5.6 cm)
40.6”*
(103.1 cm)
30.6”
(77.7 cm)
1.6”
(3.9 cm)
40.6”*
(103.1cm)
39.1”
(99.2 cm)
*NOTE: With pedestal, 52.6”
Stacked, 84”

UNPACKING THE WASHER
WARNING: Recycle or destroy the carton
and plastic bags after the washer is unpacked. Make
materials inaccessible to children. Children might use
them for play. Cartons covered with rugs, bedspreads
or plastic sheets can become airtight chambers causing
VXȺRFDWLRQ
1. Cut and remove the top and bottom packaging straps.
2. While it is in the carton, carefully lay the washer on its
side. DO NOT lay the washer on its front or back.
3. 7XUQGRZQWKHERWWRPÀDSV³UHPRYHDOOEDVHSDFNDJLQJ
including the cardboard, styrofoam base and styrofoam
tub support (inserted in center of base).
NOTE: If you are installing a pedestal, proceed to
the installation instructions that come with the pedestal.
4. Carefully return the washer to an upright position and
remove the carton.
5. Carefully move the washer to within 4 feet (122 cm)
RIWKH¿QDOORFDWLRQ
6. Remove the following from the back side of the washer:
4 bolts
4 plastic spacers (including rubber grommets)
4 power cord retainers
NOTE: Failure to remove the shipping braces can cause
the washer to become severely unbalanced.
Save all bolts for future use.
NOTE: If you must transport the washer at a later date,
you must reinstall the shipping support hardware to prevent
shipping damage. Keep the hardware in the plastic bag
provided.
In case you misplace your shipping bolts, replacements
are available at additional cost. They can be ordered in the
United States by visiting our website at GEAppliances.com
or calling 800.GE.CARES. Order kit #WH49X10039.
Installation Instructions
17

18
Installation Instructions
ELECTRICAL REQUIREMENTS
CIRCUIT – Individual, properly polarized and grounded
15-amp branch circuit fused with 15-amp time-delay fuse
or circuit breaker.
POWER SUPPLY – 2-wire, with ground, 120-volt,
single-phase, 60-Hz, alternating current.
OUTLET RECEPTACLE – Properly
grounded 3-prong receptacle to be
located so the power supply cord
is accessible when the washer is
in an installed position.
WARNING: Improper connection of the
equipment grounding conductor can result in a risk
of electrical shock. Check with a licensed electrician
if you are in doubt as to whether the appliance is
properly grounded.
1. The washer MUST be grounded. In the event of
malfunction or breakdown, grounding will reduce
the risk of electrical shock by providing a path of least
resistance for electrical current.
2. Since your washer is equipped with a power supply
cord having an equipment-grounding conductor and
a grounding plug, the plug MUST be plugged into an
appropriate, copper-wired receptacle that is properly
installed and grounded in accordance with all local
codes and ordinances or in the absence of local codes,
with the National Electrical Codes, ANSI/NFPA 70 (latest
edition). If in doubt, call a licensed electrician. DO NOT
FXWRȺRUDOWHUWKHJURXQGLQJSURQJRQWKHSRZHU
supply cord. In situations where a two-slot receptacle is
present, it is the owner’s responsibility to have a licensed
electrician replace it with a properly grounded
three-prong grounding-type receptacle.
Read these instructions completely
and carefully.
GROUNDING REQUIREMENTS
WATER SUPPLY REQUIREMENTS
Hot and cold water faucets MUST be installed within
42 inches (107 cm) of your washer’s water inlet. The faucets
MUST be 3/4” (1.9 cm) garden hose-type so inlet hoses can
be connected. Water pressure MUST be between 10 and 120
pounds per square inch. Your water department can advise
you of your water pressure. The hot water temperature
should be set to deliver water at 120° to 140°F (48°–60°C).
DRAIN REQUIREMENTS
1. Drain capable of eliminating 17 gals (64.3 L)
per minute.
2. A standpipe diameter of 1–1/4” (3.18 cm) minimum.
 7KHVWDQGSLSHKHLJKWDERYHWKHÀRRUVKRXOGEH
Minimum height: 24” (61 cm)
Maximum height: 96” (244 cm)
NOTE: The drain hose attached to the washer can reach
a 58” (147 cm) high standpipe. For a higher standpipe,
contact an authorized parts distributor.
96 in.
(244 cm)
Max.
24 in.
(61 cm)
Min.
BACK
WARNING: TO REDUCE THE RISK OF
FIRE, ELECTRICAL SHOCK AND PERSONAL INJURY:
DO NOT USE AN EXTENSION CORD OR AN ADAPTER
PLUG WITH THIS APPLIANCE.
Washer must be electrically grounded in accordance
with local codes and ordinances, or in the absence
of local codes, in accordance with the NATIONAL
ELECTRICAL CODE, ANSI/NFPA NO. 70.

INSTALLING THE WASHER
1. 5XQVRPHZDWHUIURPWKHKRWDQGFROGIDXFHWVWRÀXVK
the water lines and remove particles that might clog up
the inlet hose and water valve screens.
2. Remove the inlet hoses from the plastic bag.
3. (90° elbow end) Ensure there
is a rubber washer in the
90° elbow end of the HOT
and COLD hoses. Reinstall
the rubber washer into the
KRVH¿WWLQJLILWKDVIDOOHQRXW
during shipment. Carefully
connect the inlet hose
marked HOT to the outside
“H” outlet of the water valve.
Tighten by hand, then tighten another 2/3 turn with pliers.
Carefully connect the other inlet hose to the inside “C”
RXWOHWRIWKHZDWHUYDOYH7LJKWHQE\KDQGWKHQWLJKWHQ
another 2/3 turn with pliers. Do not crossthread or over-
tighten these connections.
4. If the inlet hose screen washers (if supplied with your
model) have fallen out during shipment, reinstall the
screen washers by inserting them into the free ends of
the HOT and COLD inlet hoses with protruded side facing
the faucet.
5. Connect the inlet hose ends to the HOT and COLD water
faucets tightly by hand, then tighten another 2/3 turn
with pliers. Turn the water on and check for leaks.
6. &DUHIXOO\PRYHWKHZDVKHUWRLWV¿QDOORFDWLRQ*HQWO\URFN
the washer into position. It is important not to damage
the rubber leveling legs when moving your washer
WRLWV¿QDOORFDWLRQ'DPDJHGOHJVFDQLQFUHDVHZDVKHU
vibration. It may be helpful to spray window cleaner on
WKHÀRRUWRKHOSPRYH\RXUZDVKHULQWRLWV¿QDOSRVLWLRQ
NOTE: To reduce vibration, ensure that all four rubber
OHYHOLQJOHJVDUH¿UPO\WRXFKLQJWKHÀRRU3XVKDQG
pull on the back right and then back left of your washer.
NOTE: Do not use the dispenser drawer or door to lift
the washer.
NOTE: If you are installing into a drain pan, you can use
a 24-inch long 2x4 to lever the washer into place.
7 :LWKWKHZDVKHULQLWV¿QDOSRVLWLRQSODFHDOHYHO
on top of the washer
(if the washer is installed
under a counter,
the washer should not
be able to rock). Adjust
the front leveling legs
up or down to ensure
the washer is resting
solid. Turn the lock nuts
on each leg up towards
the base of the washer and snug with a wrench.
NOTE: Keep the leg extension at a minimum to prevent
excessive vibration. The farther out the legs are extended,
the more the washer will vibrate.
 ,IWKHÀRRULVQRWOHYHORULVGDPDJHG\RXPD\KDYH
to extend the rear leveling legs.
19
Installation Instructions
C
H
Inlet Hose
Screen
Washers

20
Installation Instructions
INSTALLING THE WASHER (cont.)
8. Attach the U-shaped hose guide to the end of
the drain hose. Place the hose in a laundry tub or
standpipe and secure it with the cable tie provided in
the enclosure package.
NOTE: Placing the drain hose too far down the drain pipe
can cause a siphoning action. No more than 7 inches of
hose should be in the drain pipe. There must be an air
JDSDURXQGWKHGUDLQKRVH$VQXJ¿WFDQDOVRFDXVHD
siphoning action.
9. Plug the power cord into a grounded outlet.
NOTE:&KHFNWREHVXUHWKHSRZHULVRȺDWWKHFLUFXLW
breaker/fuse box before plugging the power cord into
an outlet.
10. Turn on the power at the circuit breaker/fuse box.
11. Read the rest of this Owner’s Manual. It contains
valuable and helpful information that will save you
time and money.
12. Before starting the washer, check to make sure:
Main power is turned on.
The washer is plugged in.
The water faucets are turned on.
7KHXQLWLVOHYHODQGDOOIRXUOHYHOLQJOHJVDUH¿UPO\
RQWKHÀRRU
The shipping support hardware is removed
and saved.
The drain hose is properly tied up.
There are no leaks at the faucet, drain line
or washer.
13. Run the washer through a complete cycle.
Check for water leaks and proper operation.
14. If your washer does not operate, please review
the %efore You Call For SerYiFe section before
calling for service.
15. Place these instructions in a location near the washer
for future reference.
Cable Tie Cable Tie
If replacement parts are needed for your washer, they
can be ordered in the United States by visiting our
Website at GEAppliances.com or by calling 800.GE.CARES.
REPLACEMENT PARTS
Cable Tie