GEAppliances GUD24 User manual

GEAppliances.com
Owner’s Manual
Safety Instructions ..........2-5
Operating Instructions
Care and Cleaning
oftheDryer...................... 12
Care and Cleaning
oftheWasher......................9
ControlPanelDryer...............10
ControlPanelWasher.............. 6
ControlSettingsDryer.............10
ControlSettingsWasher.........6,7
FeaturesWasher................... 8
Loading and Using
theDryer......................... 13
Loading and Using
theWasher........................9
Troubleshooting
TroubleshootingWasher.......14-16
TroubleshootingDryer........17,18
Consumer Support
Consumer Support................20
Warranty..........................19
Write the model and serial
number here:
Model # _____________
Serial # ______________
Open Dryer door for Model and
Serial number tag.
Washer/Dryer
189D7218P003
49-90532 11-14 GE Printed in Mexico
GUD24
GUD27
English/Français/Español

2
This is the safety alert symbol. This symbol alerts you to potential hazards that can kill you or hurt you and others. All safety
messages will follow the safety alert symbol and the word “DANGER”, “WARNING”, or “CAUTION”. These words are defined as:
Indicates a hazardous situation which, if not avoided, will result in death or serious injury.
Indicates a hazardous situation which, if not avoided, could result in death or serious injury.
Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
DANGER
WARNING
CAUTION
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
IMPORTANT SAFETY INSTRUCTIONS
To reduce the risk of death, fire, explosion, electric shock, or injury to persons when using your appliance,
follow basic precautions, including the following:
 Read all instructions before using the appliance.
 DO NOT wash or dry articles that have been previously cleaned in, washed in, soaked in or spotted with gasoline,
dry-cleaning solvents, or other flammable or explosive substances, as they give off vapors that could ignite or explode.

DO NOT place items exposed to cooking oils in your dryer. Items contaminated with cooking oils may contribute to a
chemical reaction that could cause a load to catch fire.
 DO NOT add gasoline, dry-cleaning solvents, or other flammable or explosive substances to the wash water. These
substances give off vapors that could ignite or explode.
 Under certain conditions, hydrogen gas may be produced in a hot-water system that has not been used for 2 weeks
or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for such a period, before using a
washing machine, turn on all hot-water faucets and let the water flow from each for several minutes. This will release
any accumulated hydrogen gas. As the gas is flammable, DO NOT smoke or use an open flame during this time.
 DO NOT allow children to play on or in this appliance. Close supervision of children is necessary when this appliance is
used near children. Before the appliance is removed from service or discarded, remove the door and lid to the drying
and washing compartments. Failure to follow these instructions may result in death or injury to persons.
 DO NOT reach into the appliance if the drum, tub or agitator is moving to prevent accidental entanglement.
 DO NOT use heat to dry articles containing foam rubber or similarly textured rubber-like materials.
 Clean lint screen before or after each load. DO NOT operate the dryer without the lint filter in place.
 DO NOT use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric
softener or product.
 Do not store combustible materials, gasoline or other flammable liquids near the dryer. Keep area around the exhaust
opening and adjacent surrounding areas free from the accumulation of lint, dust and dirt. Keep dryer area clear and free
from items that would obstruct the flow of combustion and ventilation air.
 The interior of the appliance and exhaust duct should be cleaned periodically by qualified service personnel.
 DO NOT install or store this appliance where it will be exposed to the weather.
 DO NOT tamper with controls, repair or replace any part of this appliance or attempt any servicing unless specifically
recommended in the user maintenance instructions or in published user repair instructions that you understand and
have the skills to carry out.
 DO NOT operate this appliance if it is damaged, malfunctioning, partially disassembled, or has missing or broken parts
including a damaged cord or plug.
WARNING

3
GEAppliances.com
IMPORTANT SAFETY INSTRUCTIONS
 Unplug the appliance or turn off the circuit breaker before servicing. Pressing the Power or Start/Pause button DOES NOT
disconnect power.
 DO NOT spray any type of aerosol into, on or near appliance, at any time. Do not use any type of spray cleaner when cleaning
dryer interior. Hazardous fumes or electrical shock could occur .
 Do not store items that may burn or melt (such as clothing, paper material, plastics or plastic containers, etc) on top of
the appliance nor hang them from the door.
 Never climb on or stand on this stacked unit.
 See “Electrical Requirements” located in the Installation Instructions for grounding instructions.
SAVE THESE INSTRUCTIONS
ADDITIONAL GAS DRYER WARNINGS
For your safety, the information in this manual must be followed to minimize the risk of fire or explosion
or to prevent damage, personal injury, or death.
- DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
- WHAT TO DO IF YOU SMELL GAS:
• DO NOT try to light any appliance.
• DO NOT touch any electrical switch; DO NOT use any phone in your building.
• Clear the room, building, or area of any occupants.
• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire department.
- Installation and service must be performed by a qualified installer, service agency, or the gas supplier.
WARNING
State of California Proposition 65 Warnings:
The California Safe Drinking Water and Toxic Enforcement Act requires the governor of California to publish a list of substances
known to the state to cause cancer, birth defects or other reproductive harm and requires businesses to warn of potential exposure
to such substances.
WARNING
This product contains one or more chemicals known to the State of California to cause cancer, birth defects or
other reproductive harm.
Gas appliances can cause low-level exposure to some of these substances, including benzene, carbon monoxide, formaldehyde and
soot, caused primarily by the incomplete combustion of natural gas or LP fuels. Exposure to these substances can be minimized by
properly venting the dryer to the outdoors.
SAVE THESE INSTRUCTIONS

4
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
PROPER INSTALLATION
This washer must be properly installed and located in accordance with the Installation Instructions before it is used.
If you did not receive an Installation Instructions, you can receive one by visiting GEAppliances.com or by calling
800.GE.CARES (800.432.2737). In Canada, visit www.geappliances.ca or call 800.561.3344.
* Tide®is a registered trademark of Procter & Gamble
Ensure that the hot water hose is connected to the “H”
valve and the cold water hose is connected to the “C”
valve.
Install or store where it will not be exposed to
temperatures below freezing or exposed to the weather,
which could cause permanent damage and invalidate the
warranty.
Properly ground washer to conform with all
governing codes and ordinances. Follow details
in Installation Instructions.
This washer does include water supply hoses.
GE strongly recommends the use of factory specified
parts. A list of factory hoses available for purchase are
listed below. These hoses are manufactured and tested to
meet GE specifications.
GE strongly recommends the use of new water supply
hoses. Hoses degrade over time and need to be replaced
every 5 years to reduce the risk of hose failures and water
damage.
Parts and Accessories
Order on-line at GEApplianceparts.com today, 24 hours a
day or by phone at 800.626.2002 during normal business
hours. In Canada, visit your local GE parts distributor or call
800.661.1616.
Part Number Accessory
PM14X10002 4 ft Rubber Water Supply Hoses
Or
PM14X10005 4 ft Braided Metal Water Supply Hoses
WX10X10011 Tide®Washing Machine Cleaner*
PM7X1 Washer Floor Tray
- Electrical Shock Hazard
WARNING
Plug into a grounded 3 prong outlet.
DO NOT remove ground prong.
DO NOT use an adapter.
DO NOT use an extension cord.
Failure to do so can result in death, fire or electrical
shock.

5
GEAppliances.com
WHEN NOT IN USE
Turn off water faucets to minimize leakage if a break or
rupture should occur. Check the condition of the fill hoses;
GE recommends changing the hoses every 5 years.
SAVE THESE INSTRUCTIONS
WASHER CAPACITY:
water
level
clothes water
level
clothes
water
level
clothes
Average Small Load Average Medium Load Average Large Load

6
Liquid
Bleach
Detergent Fabric Softener
STEP 3
• Select load size and
other wash options
• Select wash cycle
STEP 4
• Close lid
• Push Start
About the Washer control panel.
Note: This appliance is designed so that the washer and dryer can be operated at the same time.
Quick Start Guide
STEP 1
• Add detergent
• Add fabric softener
(optional)
• Add bleach
(optional).
STEP 2
• Add clothes
Your washer has a security system that prevents opening the
lid during the spin cycle. The lid lock prevents anyone (especially
children) from reaching into the washer while the basket is
spinning. The lid lock will be release within 5 seconds after the
basket stop spinning.
Trying to open the lid while locked could result in injuries. If the
lid does not unlock after spinning, please contact service.
NOTE: If there is a power outage the lid lock can take 3 minutes
to release.
Washer model:
GUD27
A F B C D E
Washer model:
GUD24
A F B C D E

7
GEAppliances.com
AWash Cycle Selector
The wash cycle controls the length and intensity of the washing process. The knob can be turned in either direction. Turning the
Cycle Selector knob after starting a cycle will stop the washer and reset the cycle to the new selection. Press Start to begin the
new cycle selection.
The chart below will help you match the wash cycle setting with your clothing. The chart is ranked from longest to shortest cycle
time and wash intensity. (Cycles vary by model.)
Power Clean - Uses more water than standard wash cycles. It is recommended for extra-large loads and heavily soiled clothes.
Cottons - For heavy to lightly soiled cottons, household linens, work and play clothes.
Permanent Press - For wrinkle-free and permanent press items, and knits.
Delicates - For lingerie and special-care fabrics with light to normal soil.
Quick Rinse - Rinses and spins non-soiled items where a rinse only is desired.
Spin Only - For draining the tub and spinning water out of clothes.
Off - Washer is turned off and the Start button does not function.
NOTE: When the control is turned to OFF, the Status lights are off.
NOTE: The cycle selector does not rotate during the operation of the washer.
FStart
Press Start to begin the cycle. With the lid closed pressing Start again will pause the cycle and Status lights will blink. To
continue the cycle, close the lid and press Start again. The water fill will continue with the lid opened, except when Auto Load
Sensing is selected as the load size. (The lid must be closed to continue filling when Auto Load Sensing is selected.)
If the lid is opened during the cycle, the cycle will pause and the Status lights will blink. To resume the cycle, close the lid and
press Start.
If the machine is paused for more than 24 hours, the cycle will be cancelled. To stop the cycle, turn the Cycle Selector to the
Off position.
Status light Illuminates
On When the fabric softener option has been selected.
Wash When the washer is in the wash portion of the cycle.
Rinse When the washer is in the rinse portion of the cycle.
Spin When the washer draining and/or spinning.
Lid Locked When the washer lid is locked. This feature prevents the lid from being opened while the
washer is in the spin cycle or coasting to a stop.
NOTE: If the Status lights are blinking, the operation of the washer has been paused. To resume operation
press the Start button (the lid must be closed).
Deep Rinse
Set this option when adding fabric softener to the washer.
B
Status lights
The Status lights show the stage the washer is in. When the selector knob is set to a new cycle, the Status lights will
flash momentarily, showing the stages the cycle will go through.
C
Temperature
Select the water temperature for the wash cycle (all rinses use cold water). Always follow fabric manufacturer’s care
label or instructions when laundering.
Tap Cold*uses incoming tap water, which can provide energy savings. For all other temperature selections, a mixture
of hot and cold water is used to achieve the ideal temperature for each temperature setting.
*Please note that some detergents do not fully dissolve in very cold water. If you experience this, it is
recommended you choose a setting other than Tap Cold.
D
Load Size
Loosely load clothes no higher than the top row of holes in the washer basket.
Auto Load Sensing- This selection automatically provides the correct amount of water suited to the size and type of load
placed in the unit.
E

8
About the Washer features.
The Fabric Softener Dispenser
The fabric softener dispenser automatically
releases liquid fabric softener at the proper time
during the cycle.
Do not stop the washer during the first spin. This
will cause the dispenser to empty too soon.
To use, follow these steps:
1Make sure dispenser is securely attached to .
2Use only diluted liquid fabric softener.
Pour into dispenser, using amount
recommended on package.
Never pour fabric softener directly on clothes. It
may stain them.
NOTE: Do not pour bleach into FABRIC SOFTENER
dispenser.
3Add water to dispenser until it reaches the
maximum fill line.
4Select FABRIC SOFTENER button on control
panel for proper dispersion of the fabric
softener.
Do not pour anything into the
agitator if the dispenser is removed.
Separate for cleaning
Cleaning the Fabric Softener Dispenser
1Remove the dispenser from the top of the agitator.
2Separate the dispenser cup from the cover by grasping the top and pushing down on the inside of
the cup with your fingers. Dispenser cup will pop free from the cover.
3To clean the dispenser, soak both the dispenser cup and the dispenser cover in the following solution:
1 US gallon (3.8 liters) warm water
1/4 cup (60 ml) heavy-duty liquid detergent
1 cup (240 ml) bleach
4If necessary, loosen buildup with a clean, soft cloth after soaking. Do not use a stiff brush; you may
roughen the surface of the dispenser.
5Rinse and reassemble dispenser. Place dispenser back on the agitator.
Liquid Bleach Funnel
The water fill dilutes liquid chlorine bleach as the washer fills for the wash cycle.
1Check clothing care labels for special instructions.
2Measure liquid bleach carefully, following instructions on the bottle.
Never pour undiluted liquid chlorine bleach directly onto clothes or into the wash basket.
Do not pour powdered bleach into bleach funnel.
3Before starting the washer, pour measured amount of bleach directly into bleach funnel. Avoid
splashing or over-filling dispenser. If you prefer to use powdered bleach, add it into the wash basket
with your detergent.
Do not mix chlorine bleach with ammonia or acids such as vinegar and/or rust remover. Mixing can
produce a toxic gas which may cause death.
NOTE: Do not pour bleach into FABRIC SOFTENER dispenser.

9
Sorting Wash Loads
Sort by color (whites, lights, colors), soil level, fabric type
(sturdy cottons, easy care, delicates) and whether the
fabric produces lint (terry cloth, chenille) or collects lint
(velveteen, corduroy).
Proper Use of Detergent
Add detergent and start the washer before adding
clothes so that the detergent can work effectively.
Using too little or too much detergent is a common
cause of laundry problems.
You can use less detergent if you have soft water, a
smaller load or a lightly soiled load.
Loading the Washer
Load dry items loosely, no higher than the top row of
holes in the washer basket. When loading wet items,
make sure you set the load/water level high enough
to allow the items to move freely. Water level should
just cover the clothes. To add items after washer has
started, lift the lid and submerge additional items next
to the agitator.
Do not wrap long items like sheets or pants around the
agitator.
Do not wash fabrics containing flammable materials
(waxes, cleaning fluids, etc.).
Agitation will not start with the lid up.
Wash Basket: Leave the lid open after washing to allow
moisture to evaporate. If you want to clean the basket,
use a clean soft cloth dampened with liquid detergent;
then rinse. (Do not use harsh or gritty cleaners.)
Fill Hoses: GE recommends changing the hoses every
5 years.
Exterior: Immediately wipe off any spills. Wipe with
damp cloth. Try not to hit surface with sharp objects.
Moving and Storage: Ask the service technician
to remove water from drain pump and hoses. See
the Installation Instructions packed with product for
information on how to reinstall the shipping rod to
keep the tub stationary when moving the washer. For
more information, visit GEAppliances.com or call 800.
GE.CARES (800.432.2737).
In Canada, visit GEAppliances.ca or call 800.561.3344.
Do not store the washer where it will be exposed to the
weather.
Long Vacations: Be sure water supply is shut off at
faucets. Drain all water from hoses if weather will be
below freezing.
Care and cleaning of the washer.
Loading and using the washer.
Always follow fabric manufacturer’s care label when laundering. GEAppliances.com
- Fire Hazard
WARNING
Never place items in the washer that are dampened with gasoline or other flammable liquids.
No washer can completely remove oil.
Do not dry anything that has ever had any type of oil on it (including cooking oils).
Doing so can result in death, explosion, or fire.

10
About the Dryer control panel.
Throughout this manual, features and appearance may vary from your model.
To reduce the risk of fire, electric shock, or injury to persons, read the IMPORTANT SAFETY INSTRUCTIONS before
operating this appliance.
WARNING!
WARNING WARNING
Explosion Hazard Fire Hazard
Keep flammable materials and vapors, such as gasoline, away
from dryer.
DO NOT dry anything that has ever had anything flammable on it
(even after washing).
Failure to do so can result in death, explosion, or fire.
No washer can completely remove oil.
Do not dry anything that has ever had any type of oil on it
(including cooking oils).
Items containing foam, rubber, or plastic must be dried on a
clothesline or by using an air dry cycle.
Failure to follow these instructions can result in death or fire.
12

11
IMPORTANT: Clean the lint filter each time you use the dryer
Fabric Care/Temperature
Cottons For regular to heavy cottons.
Delicates For delicates, synthetics and items labeled tumble dry low.
EASY Care For synthetics, blends, delicates and items labeled permanent press.
Quick Fluff For fluffing items without heat. Use the Timed Dry cycle.
1
Drying Cycles
Cottons For cottons and most linens. For most loads, select Optimum Dry.
Delicates For delicate items, special-care fabrics and knits.
Easy Care For wrinkle-free, permanent press and delicate items, and knits.
Timed Dry Set the Cycle Selector at the desired drying time.
Dewrinkle For removing wrinkles from items that are clean and dry or that are very lightly damp.
Quick Fluff For freshening or fluffing up already dry clothing, fabrics, linens and pillows. Use with Fluff No
Heat. Provides 10 minutes of no heat tumbling.
Automatic cycles determine fabric dryness and provide automatic sensored drying. The timer does not rotate during the
cycle until the thermostats sense that the clothes are dry, then the timer rotates automatically to Off.
Select Less Dry if you want your clothes slightly damp at the end of the drying cycle.
Select More Dry if you want them to feel drier. Timed cycles run for a selected time.
Timed Cycle
Timed Dry For manual drying. The timer rotates during the entire cycle.
Start-Close the dryer door. Press Start. Opening the door during operation will stop the dryer. To
restart the dryer, close the door and select Start to complete the cycle.
2
GEAppliances.com
Note: This appliance is designed so that the washer and dryer can be operated at the same time.

12
Care and Cleaning of the Dryer.
The Exterior: Wipe or dust any spills or washing
compounds with a damp cloth. Dryer control panel
and finishes may be damaged by some laundry
pretreatment soil and stain remover products. Apply
these products away from the dryer. The fabric may
then be washed and dried normally. Damage to your
dryer caused by these products is not covered by your
warranty.
The Lint Filter: Clean the lint filter before each use.
Slide out the grid that covers the filter. Run your
fingers across the filter. A waxy buildup may form on
the lint filter from using dryer-added fabric softener
sheets. To remove this buildup, wash the lint screen
in warm, soapy water. Dry thoroughly and replace. Do
not operate the dryer without the lint filter and grid in
place. Have a qualified technician vacuum the lint from
the dryer once a year.
Dryer Interior and Duct: The interior of the appliance
and exhaust duct should be cleaned once a year by
qualified service personnel.
The Exhaust Duct: Inspect and clean the exhaust
ducting at least once a year to prevent clogging. A
partially clogged exhaust can lengthen the drying time.
Follow these steps:
1. Turn off electrical supply by disconnecting the plug
from the wall socket.
2. Disconnect the duct from the dryer.
3. Vacuum the duct with the hose attachment and
reconnect the duct.
The Exhaust Hood: Check with a mirror that the inside
flaps of the hood move freely when operating. Make
sure that there is no wildlife (birds, insects, etc.) nesting
inside the duct or hood.
Clean lint
from mesh
Model: GUD24 Model: GUD27
Clean lint
from mesh

13
Loading and using the Dryer. GEAppliances.com
For the best drying performance, the dryer needs to be properly vented. The dryer will use more energy and run
longer if it is not vented to the specifications below. Carefully follow the details on Exhausting in the Installation
Instructions.
Venting the Dryer
Correct
Venting
Incorrect
Venting
- Fire Hazard
WARNING
This dryer MUST be exhausted to the outdoors.
Use only 4” rigid metal ducting for the home exhaust duct.
Use only 4” rigid metal or UL-listed dryer transition duct to connect the dryer to the
home exhaust.
DO NOT use a plastic vent.
DO NOT use a metal foil vent.
DO NOT exhaust into a chimney, kitchen exhaust, gas vent, wall, ceiling, attic, crawl
space, or concealed space of a building.
DO NOT install a screen in or over the exhaust duct.
DO NOT use duct longer than specified in the exhaust length table.
Failure to follow these instructions can result in death or fire.

14
Before you call for service…
Water Possible Causes What to do
Too many suds Too much detergent Measure your detergent carefully. Use less soap if you have soft water, a
smaller load or a lightly soiled load.
Water leaks
Using too much
detergent Use less detergent. Use less soap if you have soft water, a smaller load or a lightly soiled load.
Fill hoses or drain
hose is improperly
connected
Make sure hose connections are tight at faucets and rubber washers are
installed. Make sure end of drain hose is correctly inserted in and secured to
drain facility.
Household drain may
be clogged Check household plumbing. You may need to call a plumber.
Constant water
pressure to the fill
hoses at the water
source
Tighten hoses at the faucets and turn the water off after
each use.
Check condition of the fill hoses; they should be replaced
every 5 years.
Water temperature
seems incorrect
Cooler water
temperatures provide
improved energy
efficiency
New laundry detergents have been formulated to work with cooler water
temperatures without affecting wash performance.
Water supply
is turned off or
improperly connected
Turn both hot and cold faucets fully on and make sure hoses are connect-
ed to correct faucets.
Water valve screens
are stopped up
Turn off the water source and remove the water connection hoses from the
upper back of the washer. Use a brush or toothpick to clean the screens in
the machine. Reconnect the hoses and turn the water back on.
House water heater is
not set properly Make sure house water heater is delivering water at 120°F–140°F (48°C– 60°C).
Water pumped
out before cycle is
complete
Lid lifted or cycle was
put in pause for over
24 hours
Reset cycle.
Water won’t drain Drain hose is kinked or improperly
connected
Straighten drain hose and make sure washer is not sitting on it.
Top of drain outlet should be less than 8 ft (2.5 m) above floor.
Washer pauses during
spin cycle This is normal The washer may pause during the spin cycle to remove soapy water more efficiently.
Can hear but not see
water at the end of
the cycle This is normal The pump pleaves a little water in its intake and this is diluted with clean
rinse water.
Troubleshooting Tips
Save time and money! Review the charts on the following pages, or visit GEAppliances.com.
In Canada, visit GEAppliances.ca. You may not need to call for service.

15
Washer Operation Possible Causes What to do
Washer won’t operate
Washer is unplugged Make sure cord is plugged securely into a working outlet.
Water supply is turned off Turn both hot and cold faucets fully on.
Controls are not set
properly Check controls.
/LGLVRSHQ³VDIHW\IHDWXUH
prevents agitation and
spinning when lid is up Close lid and reset cycle, to the beginning if necessary.
Circuit breaker/fuse is
tripped/blown Check house circuit breakers/fuses. Replace fuses or reset breaker. Washer should have separate outlet.
Electronics need to be reset Unplug washer, wait 2 minutes, plug back in and press Start.
Start was not pressed Press Start.
Lid magnet missing Call for service.
Movement inside
machine when shut
off
Shifting mechanism is dis-
engaging the motor When the machine is manually turned off, the shifter will disengage the motor before completely shutting down.
If lid is raised before the motor is disengaged, it will resume
when lid is closed.
Washer Performance Possible Causes What to do
Clothes too wet Incorrect spin cycle selected Make sure the spin cycle selected matches the load you are
washing. Some fabrics will feel wetter when rinsed with cold water.
Colored spots
Incorrect use of fabric
softener
Check fabric softener package for instructions and follow directions
for using dispenser.
Pretreat stain and rewash.
Dye transfer Sort whites or lightly colored items from dark colors
Grayed or yellowed
clothes
Not enough detergent Use more detergent (especially with larger loads). Be sure to follow
detergent manufacturer’s directions.
Hard water Use a water conditioner like Calgon brand or install
a water softener.
Water is not hot enough Make sure water heater is delivering water at 120°F–140°F (48°C–
60°C).
Washer is overloaded Select load size to match clothes load.
Detergent is not dissolving Add detergent as wash basket fills with water before you load
clothes.
Dye transfer Sort clothes by color. If fabric label states wash separately,
unstable dyes may be indicated.
Lint or residue on
clothes
Clothes are air or line dried If you do not dry your clothes with a clothes dryer, your
clothes may retain more lint.
Incorrect sorting Separate lint producers from lint collectors.
Washing too long Wash small loads for a shorter time than larger loads
Detergent not dissolving
Add detergent as wash basket fills with water, before you load
clothes.
Try a liquid detergent.
Use warmer water temperature.
Overloading Load clothes no higher than the top row of holes in the washer
basket.
Incorrect use of fabric
softener Check fabric softener package for instructions and follow directions
for using dispenser.
GEAppliances.com

16
Washer Performance Possible Causes What to do
Pilling Result of normal wear on poly-cotton blends and
fuzzy fabrics
While this is not caused by the washer, you can slow the pilling
process by washing garments inside out.
Snags, holes, tears,
rips or excessive wear
Pins, snaps, hooks, sharp
buttons, belt buckles,
zippers and sharp objects
left in pockets
Fasten snaps, hooks, buttons and zippers.
Remove loose items like pins, objects in pockets and sharp buttons.
Turn knits (which snag easily) inside out.
Undiluted chlorine bleach
Check bleach package instructions for proper amount.
Never add undiluted bleach to wash or allow clothes to
come in contact with undiluted bleach.
Chemicals like hair bleach
or dye, permanent wave
solution Rinse items that may have chemicals on them before washing.
Wrinkling
Improper sorting
Avoid mixing heavy items (like work clothes) with light items (like
blouses).
Try a fabric softener.
Overloading or incorrect
water level Load your washer so clothes have enough room to move freely with water covering all of the clothes.
Incorrect wash and dry
cycles Match Cycle selection to the type of fabric you are washing (especially for easy care loads).
Repeated washing in water
that is too hot Wash in warm or cold water.
Washer Soounds Possible Causes What to do
“Metallic clicking” Shifter mechanism is
engaging or disengaging The drive system will engage at the start of agitate and disengage when agitate is complete. This occurs multiple times during the wash.
Back and forth
“swoosh” or light
“clicking” sound during
agitate
Electric motor reversing
direction This machine has a drive system that doesn’t use gears. This sound is the motor rotating back and forth to agitate your laundry.
Quick short agitation
sounds at end of agitate Clothing redistribution At the end of agitate, the motor makes short agitation strokes to redistribute the load.
“Click” when water
stops filling Relay switch The relay makes a click sound when activated. The water level acti- vates the relay and stops filling.
“Clicking” behind Con-
trol Panel during fill Automatic Temperature Control Valve This valve mixes in cold and hot water. The “clicking” is the valve turn- ing on and off.
Water volume changes
during fill Automatic Temperature Control Valve This valve mixes in cold and hot water. The sound changes when the valves are turned on and off.
Motor “whining up”
or ”coasting down” in
spin
Motor ramping up/down
during spin cycle The motor will speed up incrementally during the spin cycle. When spin is complete, it will coast until it stops.
“Humming” Water drain pump The drain pump will make a humming sound when pumping out wa-
ter after agitation stops and continue until spin is complete.
“Gurgling” Water drain pump When the pump starts drawing in air, It starts to gurgle. The washer should then begin spinning and the sound will continue until it is
done spinning.
Before you call for service…

17
Dryer Problem Possible Causes What to do
Dryer doesn’t start
Dryer is unplugged Make sure the dryer plug is pushed completely into
the outlet.
Fuse is blown/circuit
breaker is tripped Check the house fuse/circuit breaker box and replace fuse or reset breaker. Note: Most electric dryers use 2 fuses/breakers.
Dryer doesn’t heat
Fuse is blown/circuit
breaker is tripped; the dryer
may tumble but not heat
Check the house fuse/circuit breaker box and replace both fuses or
reset both breakers. Your dryer may tumble if only one fuse is blown
or one breaker tripped.
Gas service is off Make sure gas shutoff at dryer and main shutoff are fully open.
Dryer shakes or makes
noise
Some shaking/noise is
normal. Dryer may be
sitting unevenly
Move dryer to an even floor space, or adjust leveling legs as neces-
sary until even.
Greasy spots on
clothes
Improper use of fabric
softener Follow directions on fabric softener package.
Drying dirty items with
clean ones Use your dryer to dry only clean items. Dirty items can stain clean items and the dryer.
Clothes were not completely
clean
Sometimes stains which cannot be seen when the clothes are wet
appear after drying. Use proper washing procedures before drying.
Lint on clothes
Lint filter is full Clean lint screen before each load.
Improper sorting Sort lint producers (like chenille) from lint collectors (like corduroy).
Static electricity can attract
lint See suggestions in this section under STATIC.
Overloading Separate large loads into smaller ones.
Paper, tissue, etc. left in
pockets Empty all pockets before laundering clothes.
Static occurs
No fabric softener was
used
Try a fabric softener.
BounceFabric Conditioner Dryer Sheets have been approved for
use in all GE Dryers when used in accordance with the manufac-
turer’s instructions.
Overdrying Try a fabric softener.
Adjust setting to Less Dry.
Synthetics, permanent
press and blends can cause
static Try a fabric softener.
Inconsistent drying
times Type of heat Automatic drying times will vary according to the type of heat used
(electric, natural or LP gas), size of load, types of fabrics, wetness of
clothes and condition of exhaust ducts.
GEAppliances.com

18
Dryer Problem Possible Causes What to do
Clothes take too long
to dry
Improper sorting Separate heavy items from lightweight items (generally, a well-sorted
washer load is a well-sorted dryer load).
Large loads of heavy fabrics
(like beach towels) Large, heavy fabrics contain more moisture and take longer to dry. Separate large, heavy fabrics into smaller loads to speed drying time.
Controls improperly set Match control settings to the load you are drying.
Lint filter is full Clean lint filter before every load.
Improper or obstructed
ducting
Check installation instructions for proper ducting/venting.
Make sure ducting is clean, free of kinks and unobstructed.
Check to see if outside wall damper operates easily.
Check the Installation Instructions to make sure the dryer venting is
correct.
Blown fuses or tripped cir-
cuit breaker Replace fuses or reset circuit breakers. Since most dryers use 2 fuses/breakers, make sure both are operating.
Overloading/combining
loads Do not put more than one washer load in the dryer at a time.
Underloading If you are drying only one or two items, add a few items
to ensure proper tumbling.
Clothes are wrinkled
Overdrying
Select a shorter drying time.
Remove items while they still hold a slight amount of
moisture. Select a Less Dry setting.
Letting items sit in dryer
after cycle ends Remove items when cycle ends and fold or hang immediately.
Overloading Separate large loads into smaller ones.
Clothes shrink
Some fabrics will naturally
shrink when washed. Oth-
ers can be safely washed,
but will shrink in the dryer
To avoid shrinkage, follow garment care labels exactly.
Some items may be pressed back into shape after drying
If you are concerned about shrinkage in a particular
item, do not machine wash or tumble dry it.
Before you call for service…

19
All warranty service provided by our Factory Service Centers, or an
authorized Customer Care®technician. To schedule service, on-line,
visit us at GEAppliances.com, or call 800.GE.CARES (800.432.2737).
In Canada, visit GEAppliances.ca or call 800.561.3344. Please have
serial number and model number available when calling for service.
For The Period Of: We Will Replace:
One Year Any part of the washer which fails due to a defect in materials or workmanship. During this
From the date of the limited one-year warranty, we will also provide, free of charge, all labor and related service to
original purchase replace the defective part.
This warranty is extended to the original purchaser and any succeeding owner for products purchased for home use within the USA. If the
product is located in an area where service by a GE Authorized Servicer is not available, you may be responsible for a trip charge or you
may be required to bring the product to an Authorized GE Service location. In Alaska, the warranty excludes the cost of shipping or service
calls to your home.
Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal
rights, and you may also have other rights which vary from state to state. To know what your legal rights are, consult your local or state
consumer affairs office or your state’s Attorney General.
Warrantor: General Electric Company. Louisville, KY 40225
This warranty is extended to the original purchaser and any succeeding owner for products purchased in Canada for home use within
Canada. In home warranty service will be provided in areas where it is available and deemed reasonable by Mabe to provide.
WARRANTOR IS NOT RESPONSIBLE FOR CONSEQUENTIAL DAMAGES.
Warrantor: MC COMMERCIAL, Burlington, L7R 5B6
Service trips to your home to teach you how to use the
product.
Improper installation, delivery or maintenance.
Failure of the product if it is abused, misused, or used for
other than the intended purpose or used commercially.
Replacement of house fuses or resetting of circuit breakers.
Products which are not defective or broken, or which are
working as described in the Owner’s Manual.
Damage to the product caused by accident, fire, floods or
acts of God.
Incidental or consequential damage caused by possible
defects with this appliance.
Defects or damage due to operation in freezing
temperatures.
Damage caused after delivery.
Product not accessible to provide required service.
What Is Not Covered for Customers in the United States:
Service trips to your home to teach you how to use the
product.
Improper installation, delivery or maintenance.
If you have an installation problem, contact your dealer
or installer. You are resposible for providing adequate
electrical, exhausting and other connecting facilities.
Failure of the product if it is abused, misused, or used for
other than the intended purpose or used commercially.
Replacement of house fuses or resetting of circuit breakers.
Damage to the product caused by accident, fire, floods or
acts of God.
Damage caused after delivery.
What Is Not Covered for Customers in Canada:
Staple your receipt here.
Proof of the original purchase
date is needed to obtain service
under the warranty.
This Appliance Warranty. GEAppliances.com
(;&/86,212),03/,(':$55$17,(6³<RXUVROHDQGH[FOXVLYHUHPHG\LVSURGXFWUHSDLUDVSURYLGHGLQWKLV/LPLWHG:DUUDQW\
Any implied warranties, including the implied warranties of merchantability or fitness for a particular purpose, are limited to
one year or the shortest period allowed by law.
(;&/86,212),03/,(':$55$17,(6³<RXUVROHDQGH[FOXVLYHUHPHG\LVSURGXFWUHSDLUDVSURYLGHGLQWKLV/LPLWHG:DUUDQW\
Any implied warranties, including the implied warranties of merchantability or fitness for a particular purpose, are limited to
one year or the shortest period allowed by law.

20
GE Appliances Website In the U.S. GEAppliances.com
Have a question or need assistance with your appliance? Try the GE Appliances Website 24 hours a day, any
day of the year! For greater convenience and faster service, you can now download Owner’s Manuals, order
parts or even schedule service on-line. In Canada: www.GEAppliances.ca.
Schedule Service In the U.S. GEAppliances.com
Expert GE repair service is only one step away from your door. Get on-line and schedule your service at your
convenience 24 hours any day of the year! Or call 800.GE.CARES (800.432.2737) during normal business hours.
In Canada, call 800.561.3344.
Real Life Design Studio In the U.S. GEAppliances.com
*(VXSSRUWVWKH8QLYHUVDO'HVLJQFRQFHSW³SURGXFWVVHUYLFHVDQGHQYLURQPHQWVWKDWFDQEHXVHGE\SHRSOHRI
all ages, sizes and capabilities. We recognize the need to design for a wide range of physical and mental abilities
and impairments. For details of GE’s Universal Design applications, including kitchen design ideas for people with
disabilities, check out our Website today. For the hearing impaired, please call 800.561.3344.
In Canada: contact: Director, Consumer Relations, Mabe Canada Inc.
Suite 310, 1 Factory Lane
Moncton, N.B. E1C 9MC
Extended Warranties In the U.S. GEAppliances.com
Purchase a GE extended warranty and learn about special discounts that are available while your warranty is still in
effect. You can purchase it on-line anytime, or call 800.626.2224 during normal business hours. GE Consumer Home
Services will still be there after your warranty expires. In Canada, please visit our Website or contact your local
extended warranty provider.
Parts and Accessories In the U.S. GEAppliances.com
Individuals qualified to service their own appliances can have parts or accessories sent directly to their homes (VISA,
MasterCard and Discover cards are accepted). Order on-line today, 24 hours every day or by phone at 800.626.2002
during normal business hours.
Instructions contained in this manual cover procedures to be performed by any user. Other servicing generally
should be referred to qualified service personnel. Caution must be exercised, since improper servicing may cause
unsafe operation.
Customers in Canada should consult the yellow pages for the nearest GE parts distributor or call 800.661.1616.
Contact Us In the U.S. GEAppliances.com
If you are not satisfied with the service you receive from GE, contact us on our Website with all the details including
your phone number, or write to: General Manager, Customer Relations
GE Appliances, Appliance Park
Louisville, KY 40225
In Canada: GEAppliances.ca, or write: Director, Consumer Relations, Mabe Canada Inc.
Suite 310, 1 Factory Lane
Moncton, N.B. E1C 9MC
Register Your Appliance In the U.S. GEAppliances.com
5HJLVWHU\RXUQHZDSSOLDQFHRQOLQH³DW\RXUFRQYHQLHQFH Timely product registration will allow for enhanced
communication and prompt service under the terms of your warranty, should the need arise. You may also mail in the
pre-printed registration card included in the packing material. In Canada: www.GEAppliances.ca.
Consumer Support.