GEC Cafe Vienna series User manual

Base Cabinet Assembly Instructions
Tools needed: Flat head screwdriver, wood glue, rubber mallet, drill Optional: Nail gun, Stapler
1. First put the grey rail holders into the holes on the back panel. Then lock the back panel onto a side
panel.
2. Next slide in the bottom panel.
3. Lock on the side panel for the other side.
4. Lock on the face frame. IF the side panels or bottom panel are a little warped, tap it with the rubber
mallet.
5. Add on toekick piece.
6. Assemble the drawers together with wood glue and the rubber mallet.
7. Put in the rails. Place the front of the rails at the bottom of the openings for each drawer before
screwing them in.
8. Put in the drawers.

Drawer Base Cabinet Instructions
Items needed: Flat head screwdriver, Wood Glue, Drill, rubber mallet Optional: Nail Gun, Stapler
1. First put the grey rail holders into the holes on the back panel. Then lock the back panel onto a side
panel.
2. Next slide in the bottom panel.
3. Lock on the side panel for the other side.
4. Lock on the face frame. IF the side panels or bottom panel are a little warped, tap it with the rubber
mallet.
5. Add on toekick piece.
6. Assemble the drawers together with wood glue and the rubber mallet.
7. Put in the rails. Place the front of the rails at the bottom of the openings for each drawer before
screwing them in.
8. Put in the drawers.

Base Lazy Susan Assembly Instructions
Tools Required: Drill, Rubber Mallet, Another Person, Wood Glue Optional: Nail guns, Staplers
First lock the side panels together. The wooden piece attached to the side panels should be at the bottom for
all the panels.
1. Next lock the large square frame onto the front of the left set side panels. Lock the C-Frame onto the
right set of side panels.
2. Now carefully set in the large plate with one spinning shelf pre-attached to it.
3. Push the side panels together towards the large plate. Make sure the grooves in the back are perfectly
flush.
4. Next slide in the thin back plate into that groove. Combine both side panels using the trapezoid

connector piece and lock the cam locks.
5. Attach the C-Frame onto the square frame with an L Bracket and attach the square frame onto the side
panel using the long screws.
6. Mount the spinning shelf onto the rectangular board with the black spinning hardware plate. Attach it
onto the side panels LAST.
7. Next screw the hinges onto the doors and attach the doors onto the square frame.
8. Now set the entire Lazy Susan off on one of the side panels and lock the toe kicks using, left one first.
9. Now set in the middle shelf of the Lazy Susan and screw it onto the ledges on the side panels using the
long screws.

Wall Cabinet Assembly Instructions
Items Needed: Drill, Rubber Mallet, and for some cabinets, a screwdriver, Wood glue Optional: Nail Guns, Stapler
1. Put the back panel in the back groove on one of the side panels.
2. Lock in both the bottom and top pieces. For the smaller cabinets there are no cam locks on these.
3. Lock on the other side panel.
4. Lock on the face frame.
5. Insert shelf pins and shelves.

Diagonal Wall Corner Cabinet (Cam Lock)
Items Needed: Rubber Mallet a flat-head screwdriver. Optional: Nail Guns, Wood Glue, Stapler
1. Line up the grooves of the side panels, 1 wide one and one narrow one. Make sure all the cam locks
are open. Lock the two sets of side panels together.
2. Next take 1 set of side panels and attach the hexagon tops and bottoms by interlocking the cam locks.
3. Carefully attach the second set of side panels onto the other side of the top and bottom panels.
4. Put the doorframe onto the side where cam locks are showing. Lock the top and bottom cam locks first
before locking the ones within the cabinet frame.
5. Slide in back panel. May need to hammer a little bit to fully slide it down.
6. Insert shelf pins and shelves.