Gehl 5625SX User manual

INTERNATIONAL SYMBOLS
@ @ ®
(£)
Q
'6/
...... ,.
'/v~
///11
I \
STARTER IGNITION ON ALL POWER POWER ON WORK LIGHT EMERGENCY
OR
OFF ACCESSORIES HAZARD FLASHER
~
~
® 0
c15
-v'-
HORN ENGINE OIL ENGINE HOURS AMMETER
OR
HEATER FUSE
PRESSURE (Running Time) GENERATOR LIGHT STARTER
A •
~~
IS]
c::J
~
Full
y
~
Gasoline CHOKE Engaged
ENGINE COOLANT'
1/2 Full HYDRAULIC
\0
TEMPERATURE JI)
(j)
RESERVOIR
* 0 t
Empiv
Diesel Disengaged
VOLUME LEVEL FUEL ENGINE OIL • HAND BRAKE
,--,
~
•
r"
,,-U/#.
~r-
CAUTION:
'N'
~
~
PRESSURIZED
..
, , --DIRECTION OF
RADIATOR '--'
4Itt
~
CONTROL LEVER
"n\'
.\~
Floal
NEUTRAL ROTATE ROTATE C
if'
CLOCKWISE COUNTERCLOCKWISE
+ @
~:.~
r •
Faal +
Dump
Lower
FUEL
REVERSE FORWARD SHUT-OFF
~
....,
8
/'
'-.-
~~,
e
Slow , Roll Back
• Raise
SPEED RANGE COOLANT GREASE DIPSTICK BUCKET CONTROL LIFT ARM CONTROL

Chapter
1
2
3
4
5
6
7
8
9
10
11
12
13
TABLE OF CONTENTS
Description
International Symbols
Introduction. .
Specifications .
Check Lists . .
Safety ..... .
Controls & Safety Equipment
Operation
..
Adjustments ....... .
Lubrication . . . . . . . . .
Attachments & Accessories
Troubleshooting
Service
....... .
Decal
Locations. . . .
Maintenance Schedule
Index
........ .
Standard Hardware Torque
Warranty
........ .
IDENTIFICATION INFORMATION
Page
Inside Front Cover
.2
.4
.7
10
18
29
39
43
46
49
57
73
78
82
86
Inside Back Cover
Write your Gehl Loader Model and Serial Numbers in the space provided below.
Refer to these numbers when inquiring about parts or service from your Gehl dealer.
jMOOEL N5 L
jSERIAL N_O_o ________________ __
CicHL®
WEST BEND, WI 53095 U.S.A.
The Model and Serial Numbers for this Loader are on a Decal located inside the
right Chassis Riser, between the Lift Arm and Lift Cylinder.
1

HAPTER 1
INTRODUCTION
The information in this Operator's Manual was written to give the owner/operator assistance in preparing, adjusting,
maintaining and servicing
of the Loader. More importantly, this manual provides an operating plan for safe and proper
use
of the machine. Majorpoints of safeoperation are detailed in the SAFETY chapter of this manual. Achart of standard
hardware torques
is located in the back of this manual.
The GEHL Company asks that you read and understand the contents of this manual COMPLETELY and become
familiar with your new machine, BEFORE attempting to operate it.
Throughout this manual, information
is provided which is set in italic type and introduced by the word NOTE. Be sure
to read carefully and comply with the message ordirective given. Following this information will improveyouroperating
or maintenance efficiency, help you to avoid breakdowns or damage and extend your machine's life.
A plastic container
is provided on the unit for storing the Operator's Manual. After using the Manual, please return it to
the container and keep it with the unit at all times!
If this machine is resold, GEHL Company recommends that this
Manual be given
to the new owner.
"Right" and "left" are determined from a position sitting on the Seat and facing forward. From this position:
If your Loader is T-Bar Controlled: the Propulsion (Traction) Control T-Bar is on the "left" and the Liftffilt Control
T-Bar
is on the "right".
If your Loader is Hand/Foot Controlled: The "left" T-Bar controls the Propulsion (Traction) on the left side of the
machine. The "right"
T- Barcontrols Propulsion (Traction) on the rightside of the machine. The "leji" FootPedal controls
the Lift. The "right" Foot Pedal controls the Tilt.
Our wide Dealership network stands by to provide you with any assistance you may require, including genuine GEHL
service parts. All parts should be obtainedfrom ororderedthrough your GEHL Dealer. Give complete information about
the PaIt and include the model and serial numbers
of your machine. Record the serial number in the space provided on
the previous page, as a handy record for quick reference.
GEHL Company reserves the right to make changes or improvements in the design or construction of any part without
incurring the obligation to install such changes on any unit previously delivered.
2
The GEHL Company, in cooperation with the
American Society of Agricultural Engineers and the
Society of Automotive Engineers, has adopted this
SAFETY ALERT SYMBOL
to pinpoint characteristics which, if NOT properly
followed, can create a safety hazard. When you see
this symbol in this manual or on the machine itself,
you are reminded to BE ALERT! Your personal safety
is involved!

Loader Identification
AUXILIARY
QUICK
COUPLERS
FRONT WORK
LIGHTS
TILT CYLINDERS
BUCKET
REAR GRILL
REAR WORK
LIGHT RESTRAINT
BAR
LIFT CYLINDER
LOCK
LIFT CYLINDER
SEAT BELT
TIRES
LIFT ARM
3

CHAPTER 2
SPECIFICATIONS
Gehl Skid Loader Models:
Engine: 5625SX,5625DX
Make . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. Perkins
Model
................................................... , Model 204-25
Fuel
............................................................ Diesel
Displacement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.. 152 cm (2.5L)
Horsepower-Gross
........................... SAE 56 hp (42 kW) @ 2700 rpm
Torque -Max.. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.. 111 ftllbs (150 Nm) @ 2200 rpm
Electrical :
Battery .......................................... 12 Volt DC with 950 CCA
Starter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12 Volt DC
Alternator
....................................................... 40 amp
*SAE Operating Capacity:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 1700 Ibs (77 I Kg)
Shipping Weight: .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 5255 Ibs (2384 Kg)
Capacities:
Fuel Tank: ............................................ 16 Gallons (61 liters)
Hydraulic Reservoir:
................... 14 Gallons (53 liters) with 4 Micron Filter
Chaincases:
...................................... 2 Gallons (7.6 liters) each
Engine Oil:
........................................... 6.3 Quarts (6 liters)
Delivery Rates:
Hydraulic System Pump:
Standard (Single) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.. 2 I gpm (79.5 IIm)
High Flow (Dual) (DX Models) ........................... 32.4 gpm (122.6 11m)
Travel Speed: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 0 to 6.5 mph (0 to 10.4 kph)
*Operating capacity rated with 68" (1727 cm) wide Dirt/Construction Bucket, 12.00 x 16.5 Tires and a
175 Ib (79 kg)
operator in accordance with SAE J818.
Tire Options Buckets & Capacities
Flotation Tire Set -12.00 x 16.5 6 - ply
Capacity
Width (Heaped)
Heavy Duty Flotation Tire Set -12.00 x 16.5 10 -ply
High Clearance Flotation Tire Set -14.5 x
17 10 -ply
Chevron Tire Set -8.25 x
15 6 - ply
in(mm} Bucket Descri[2tion cu ft cu m
Solid Rubber Tire Set -8.00 x 16
AirBoss Segmented Industrial Tire Set -8.25 x 15
AirBoss Segmented Flotation Tire Set -12.00 x 16.5
Extra Wide Tire Set -
31 x 15.5 xiS 8 - ply
4
65 (1651)
68 (1727)
68 (1727)
72 (1829)
72 (1829)
72 (1829)
Utility
Dirt/Construction
Dirt/Construction with Teeth
Dirt/Construction
Utility (Agriculture Use)
Light Material
19 .54
14 .40
14 .40
17 .48
21
.59
21 .59

Standard Features
e Side-Mount "Load Trak" T-Bar Controls
e Power-Assist Controlled Hydrostatic Drive
e ROPS-FOPS ISO Level 2 Approved Overhead Guard
e Self-Level Lift Action
.. Independent Hydraulic Reservoir
.. Operator Restraint Bar with Armrests
e Seat and Operator Restraint Bar Interlock for Starter,
Lift Cylinders, and Tilt Cylinders
e Adjustable Contoured Seat with Seat Belt
.. Mechanical Lift Cylinder Lock
.. Integral Belly Plate with Cleanout
• Hourmeter
.. Coolant Temperature Gauge
.. Fuel Gauge
• Oil Pressure, Battery Charge Indicators
.. Hand and Foot Throttle-Hand Controls
III Glow Plug Statting Assist
III Disc Type Handbrake
e Operational Lights - 2 Front, I Rear
III Spark Arrestor Muffler
• Locking Fuel Cap
• Dual Element Air Cleaner
III Front Auxiliary Hydraulics with 3/4" Couplers
• Gehl Quick-Lock Attachment Mounting
III Sound Deadening Package
• 50/50 Anti-Freeze Protection
Accessories
• 3" Seat Belt -Where required by Law
III Centrifugal Pre-Cleaner
III All Weather Rigid Cab Enclosure with Door Kit
III Vinyl Cab Enclosure Kit
.. Wiper Kit
.. HeaterlDefroster Kit
.. Back-Up Alarm
III Dual Flasher Kit
.. Strobe Light
.. Horn Kit
.. Lift Kit
.. Hydraulic Reservoir Heater
.. Enclosed Alternator - 12 Volt, 30 Amp
• Suspension Seat
• Engine Heater -Block -400 Watt
.. Engine Auto-Shutdown System Kit
• Battery Disconnect Switch
5

A
General Specifications
SL56SX/DX
6
inch
A Overall Operation Height -Fully Raised ........................ 14S.S
B Height to Hinge Pin- Fully Raised. . . . . . . . . . . . . . . . . . . . . . . . . . .. 119.0
C Overall Height-Top of Operator Guard. . . . . . . . . . . . . . . . . . . . . . . .. SI.O
D Ground Clearance-to Chassis .................................. 9.4
E Overall Length (w/6S" DirtlConstruction Bucket) ................ 126.3
F Overall Length (less Bucket) ................................. 9S.6
G Wheel Base .............................................. 39.5
H Dump Reach-w/6S" Dirt/Const. Bucket (full height) ............... 2S.0
Dump Reach-w/6S" Dirt/Const. Bucket (116" height)
.............. 29.3
Dump Reach-w/72" Utility Bucket (full height)
................... 32.0
I Rollback at Ground ......................................... 25°
J Dump Angle ............................................... 41°
K Overall Width-less Bucket (w/S.25 x 15 Tires) .................... 61.0
Overall Width-less Bucket (wI12.00 x 16.5 Tires)
................. 66.4
L Bucket Width (Dirt-Const. Bucket)-Overall ...................... 69.0
M Clearance Circle -Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 5S.S
N Clearance Circle -Front (less Bucket) . . . . . . . . . . . . . . . . . . . . . . . . . . 4S.0
o Clearance Circle -Front (w/6S" Dirt/Const. Bucket) ............... 76.7
P Seat to Ground Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41.5
Q Rollback at Full Height ...................................... 91 °
R Dump Height. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 94.0
S Departure Angle ............................................ 2So
Reach Maximum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40.1
Dump Height at Maximum
Reach. . . . . . . . . . . . . . . . . . . . . . . . . . . .. 70.0
Height to Top
of Rise ....................................... 73.0
Maximum Back Grading Angle
................................ S2°
(mm)
(37S0)
(3023)
(2057)
(239)
(320S)
(2504)
(1003)
(711)
(744)
(SI3)
(1549)
(16S7)
(1753)
(1494)
(1219)
(1945)
(1054)
(23SS)
(1019)
(l77S)
(lS54)

c
o
:;::::;
~
o
't:
Q)
a.
-
ctS
~
o
()
~
ii:
~C/)
...
Q)
C6
Q)
c
Q)
>
o
E
Q)
a:
CHAPTER 3
CHECKLISTS
PRE-DELIVERY
The following Checklist is an important reminder of
valuable information and inspections which MUST be
made before delivering the Loader
to the Customer.
Check offeach item after prescribed action
is taken.
Check that:
D Unit has NOT been damaged in shipment. Check for such
things
as dents and loose or missing parts; con-ect or
replace components
as required.
D Battery is securely mounted and NOT cracked, cable con-
nections are tight, and Battery Disconnect Switch (if
equipped)
is in the "ON" position.
D Lift and Tilt Cylinders, Hoses and Fittings are NOT dam-
aged, leaking or loosely connected.
D Radiator Hoses and Fittings are NOT damaged, leaking or
loosely connected.
D Filters are NOT damaged, leaking or loosely secured.
D Wheels are properly and securely attached and Tires are
properly inflated.
D Loader is properly lubricated and NO Grease Fittings are
missing or damaged.
D Hydraulic System Reservoir, Engine Crankcase and Drive
Chaincases are filled to their proper levels.
D All adjustment are made to comply with settings given in
the Adjustments chapter of this manual.
D All Guards, Shields and Decals are in place and securely
attached.
D Model and Serial Numbers, for this unit, m'e recorded in
space provided on this page and page
I.
Start Loader Engine and test-run the unit while
checking that proper operation is exhibited by all
controls.
Check that:
D Propulsion Control and Lift/Tilt Control T-bars or
Hand/Foot Controls operate properly and are NOT dam-
aged or binding.
D Propulsion Control T-bar orHandlFoot Controls are prop-
erly adjusted for a correct "neutral" position so that Loader
does NOT creep.
D Lift Cylinder and Starter Interlock system functions prop-
erly. By design, the Engine will NOT start unless the
Operator is sitting on the Seat and the Restraint Bar
is
"lowered". Furthermore, the Lift and Tilt Circuits will not
operate unless the Operator is sitting on the Seat, the
Restraint Bar is "lowered", and the Starter Key Switch is
in the "Run" position.
I acknowledge that pre-delivery procedures were per-
formed on this unit at outlined above.
Dealership Name
Dealer Representative's Name
Date Checklist Filled-out
Loader Model# Loader Serial# Engine Serial#
Delivery
Check that:
The following Checklist is an important reminder of
valuable information that MUST be passed on to the
Customer at the time the unit
is delivered. Checkoffeach
item as you explain it to the Customer.
Review with the Customer the contents
of this manual;
especially:
D The INDEX at the back, for quickly locating topics;
D The SAFETY, CONTROLS & SAFETY EQUIPMENT
and OPERATION Chapters, for information regarding
safe use
of the machine;
D The ADJUSTMENTS, LUBRICATION, SERVICE and
TROUBLESHOOTINGChapters, for informationregard-
ing proper maintenance
of the machine. Explain that regu-
lar lubrication and maintenance are required for continued
safe operation and long life.
D Give this Operator's Manual to the Customer and instruct
the Customerto be sure to read and completely understand
its contents BEFORE operating the unit.
D Explain that the Customer MUST consult the Engine
Manual (provided) for related specifications, operating
adjustments and maintenance instructions.
D Completely fill out the Owner's Registration, including
Customer's signature and, return it to the company.
Customer's Signature
Date Delivered
(Dealer's File Copy)
7

INTENTIONALLY BLANK
(To be removed as Dealer's file copy)
8

CHAPTER 3
CHECKLISTS
PRE-DELIVERY
The following Checklist is an important reminder of
valuable information and inspections which MUST be
made before delivering the Loader
to the Customer.
Check offeach item after prescribed action
is taken.
Check that:
D Unit has NOT been damaged in shipment. Check for such
things as dents and loose or missing parts;
COlTect or
replace components
as required.
D Battery is securely mounted and NOTcracked, cable con-
nections are tight, and Battery Disconnect Switch (if
equipped) is
in the "ON" position.
D Lift and Tilt Cylinders, Hoses and Fittings are NOT dam-
aged, leaking or loosely connected.
D Radiator Hoses and Fittings are NOT damaged, leaking or
loosely connected.
D Filters are NOT damaged, leaking or loosely secured.
D Wheels are properly and securely attached and Tires are
properly inflated.
D Loader is properly lubricated and NO Grease Fittings are
missing or damaged.
D Hydraulic System Reservoir, Engine Crankcase and Drive
Chaincases are filled to their proper levels.
D All adjustment are made to comply with settings given in
the Adjustments chapter of this manual.
D All Guards, Shields and Decals are in place and securely
attached.
D Model and Serial Numbers, for this unit, are recorded in
space provided on this page and page 1.
Start Loader Engine and test-run the unit while
checking that proper operation is exhibited by all
controls.
Check that:
D Propulsion Control and Lift/Tilt Control T-bars or
HandlFoot Controls operate properly and are NOT dam-
aged or binding.
D Propulsion Control T-bar or Hand/Foot Controls are prop-
erly adjusted for a correct "neutral" position so that Loader
does NOT creep.
D Lift Cylinder and Starter Interlock system functions prop-
erly. By design, the Engine will NOT start unless the
Operator is sitting on the Seat and the Restraint Bar
is
"lowered". FUlthermore, the Lift and Tilt Circuits will not
operate unless the Operator
is sitting on the Seat, the
Restraint Bar is "lowered", and the Starter Key Switch is
in the "Run" position.
I acknowledge that pre-delivery procedures were per-
formed on this unit at outlined above.
Dealership Name
Dealer Representative's Name
Date Checklist Filled-out
Loader Model#
Loader Serial#
Engine Serial#
Delivery
Check that:
The following Checklist is an important reminder of
valuable information that MUST be passed on to the
Customer at the time the unit
is delivered. Checkoffeach
item as you explain it
to the Customer.
Review with the Customer the contents
of this manual;
especially:
D The INDEX at the back, for quickly locating topics;
D The SAFETY, CONTROLS & SAFETY EQUIPMENT
and OPERATION Chapters, for information regarding
safe use
of the machine;
D The ADJUSTMENTS, LUBRICATION, SERVICE and
TROUBLESHOOTINGChapters,forinfonnation regard-
ing proper maintenance
of the machine. Explain that regu-
lar lubrication and maintenance are required for continued
safe operation and long life.
D Give this Operator's Manual to the Customer and instruct
the Customerto be sure to read and completely understand
its contents BEFORE operating the unit.
D Explain that the Customer MUST consult the Engine
Manual (provided) for related specifications, operating
adjustments and maintenance instructions.
D Completely fill out the Owner's Registration, including
Customer's signature and, return
it to the company.
Customer's Signature
Date Delivered
(Pages 7 & 8 have been removed atPerforation)
9

CHAPTER 4
The above Safety Alert Symbol means ATTENTION!
BECOME ALERT! YOUR SAFETY IS IN-
VOLVED! It stresses an attitude of "Heads Up for
Safety" and can be found throughout this Operator's
Manual and on the machine itself.
BEFORE YOU ATTEMPT TO OPERATE THIS
EQUIPMENT, READ AND STUDY THE FOL-
LOWING SAFETY INFORMATION. IN ADDI-
TION, MAKE SURE THAT EVERY
INDIVIDUAL WHO OPERATES OR WORKS
WITH THIS EQUIPMENT, WHETHER FAMILY
MEMBER OR EMPLOYEE, IS FAMILIAR
WITH THESE SAFETY PRECAUTIONS.
Our Company ALWAYS takes the operator's safety
into consideration when designing its machinery, and
guards exposed moving parts for the operator's pro-
tection. However, some areas can NOT be guarded or
shielded in order to assure proper operation. In addi-
tion, this Operator's Manual, and Decals on the ma-
chine, warn
of further danger and should be read and
observed closely.
DAN ER
"DANGER" indicates an imminently hazardous
situation which,
if not avoided, will result in
death or serious injury.
WARNING
"WARNING" indicates a potentially hazardous situ-
ation which,
if not avoided, could result in death or
serious injury.
CAUTI
N
"CAUTION" indicates a potentially hazard-
ous situation which, if not avoided, may result
in minor or moderate injury. May also alert
against unsafe practices.
10
MANDATORY SAFETY SHUTDOWN
PROCEDURE
BEFORE unclogging,cleaning, adjusting,lubricat-
ing or servicing the unit:
1. Move the Propulsion Control T-bar(s) to the "neutral"
position.
2. Lower the Lift Arm and Attachment completely.
Also, see Step 5, below.
3. Move the Throttle to the low idle position, shut the
Engine offand remove the
Key.
4. Apply the Parking Brake.
S. If the Lift Arm MUSTbe left in the "raised" position,
BE SURE to properly engage the Lift Cylinder Me-
chanical Lock instead
of performing step 2.
ONLY when you have taken these precautions can
you be sure it is safe to proceed. Failure to follow
the above procedure, could lead to death orserious
injury.
ADDITIONAL SAFETY REMINDERS
e Some photographs in this manual may show
Doors, Guards and Shields open or removed for
illustrative purposes
ONLY. BE SURE that all
Doors, Guards and Shields are in their proper
operating positions BEFORE starting the engine
to operate the unit.
e To ensure safe operation, replace damaged
or
worn-out parts with genuine Gehl service parts,
BEFORE attempting to operate this equipment.
e GEHL Skid Loaders are designed and intended to
be used ONLY with GEHLCompany Attachments
or approved Referral Attachments. The GEHL
Company can NOT be responsible for operator
safety
if the Loader is used with a non-approved
Attachment.

SA
ETV
(CONTINUED)
• The stability of a Skid Loader is determined by its
short wheel base. The following elements: the
terrain,
Engine speed, load being carried or
dumped, and/or abrupt Control movements, can
affect stability. IF MISUSED, ANY OF THE
ABOVE FACTORS CAN CAUSE THE
LOADER TO TIP, THROWING YOU FOR-
WARD OR OUT OF THE UNIT, CAUSING
DEATH
OR SERIOUS INJURY. Therefore,
ALWAYS have the Operator Restraint Bar
"low-
ered" and wear the Seat Belt. Operate the Controls
smoothly and gradually at an appropriate Engine
speed which matches the operating conditions.
• For additional stability when operating on inclines
or ramps, ALWAYS travel with the heavier end
of
the Loader to the top of the incline.
• NEVER attempt to by-pass the Keyswitch to start
the Loader Engine. Only use the jump-starting
procedure detailed in the service chapter
of this
manual.
• Do NOT attempt to remove the Radiator Cap after
the Engine has reached operating temperature or
has overheated because the Engine Coolant will be
extremely
HOT and under pressure. ALWAYS
wait for the Engine to cool down BEFORE at-
tempting to relieve pressure and remove the Ra-
diator Cap. Failure to heed could result in severe
burns.
• NEVER use your hands to search for hydraulic
fluid leaks, use a piece
of paper or cardboard.
Escaping fluid under pressure can be invisible and
can penetrate the skin and cause a serious injury.
If any fluid is injected into your skin, see a doctor
at once. Injected fluid MUST be surgically re-
moved by a doctor or gangrene may result.
•
ALWAYS wear safety glasses with side shields
when striking metal against metal. In addition, it
is also recommended that a softer (non-chipable
material) be used to cushion the blow. Failure
to
heed could lead to serious injury to the eyes or
other parts
of the body.
• DO NOT raise or drop a loaded Bucket or Fork
suddenly. Abrupt movements under load can cause
serious instability.
•
DO NOTpush the Lift Control all the way forward
(into the
"float" position) with the Attachment
loaded and the Lift Arm raised as this will cause
the Lift Arm to drop, very rapidly.
• DO NOT drive too close to an excavation or ditch;
BE SURE that the surrounding ground has ade-
quate strength to support the weight
of the Loader
and the load.
• DO NOT smoke or have any spark producing
equipment in the area while filling the Fuel Tank
or while working on the fuel or hydraulic systems.
11

ALWAYS USE
MECHANICAL LOCK
WHEN LEAVING LIFT
ARM IN THE RAISED
POSITION FOR
SERVICING LOAOER.
BEFORE SERVICING
LOADER, PROCEED AS
SPECIFIED IN THE
OPERATOR'S MANUAl.
FAILURE TO HEED
COULD RESULT IN
DEATH OR SERIOUS
INJURY.
OPERATING
CONDITIONS COULD
PRODUCE JERKY
MOVEMENT.
BEFORE STARTING
ENGINE FASTEN SEAT
BELT.
FAILURE TO HEED
COULD RESULT IN
DEATH OR SERIOUS
INJURY.
123912
12
KEEP FEET INSIDE
COMPARTMENT AND
OFF LEDGE.
FAILURE TO HEED
COULO RESULT IN
DEATH OR SERIOUS
INJURY.
DO NOT USE BRAKE
TO TEST
HYDROSTATIC DRIVE
TORQUE.
OVERHEATING AND
ACCELERATED WEAR
OF THE DISC AND
PADS CAN OCCUR.
FAILURE TO HEED
COULD RESULT IN
DEATH OR SERIOUS
INJURY.
123912
123912
(CONTINUED)
OR MAXIMUM STABILITY CARRY LOAD AS LOW AS POSSIBLE.
AlLURE TO HEED COULD RESULT IN DEATH OR SERIOUS INJURY.
BEFORE OPERATING
WITH ATTACHMENT,
CHECK LOCKING PIN
ENGAGEMENT OF THE
QUICK-TACH TO THE
ATTACHMENT.
FAILURE TO HEED
COULD RESULT IN
DEATH OR SERIOUS
INJURY.
122718
093475
FOR MAXIMUM STABILITY CARRY
LOAD AS LOW AS POSSIBLE.
FAILURE TO HEED COULD RESULT
IN DEATH OR SERIOUS INJURY.
093479

DO NOT BYPASS ENGINE KEYSWITCH BY CONNECTING AT THE
STARTER TERMINALS TO JUMP START. FOLLOW RECOMMENDED
PROCEDURE IN THE OPERATOR'S MANUAL FOR JUMP STARTING
USING THE ENGINE KEYSWITCH.
STARTING IN GEAR COULD OCCUR IF THE STARTING CONTROL
CIRCUIT IS BYPASSED.
FAILURE TO HEED COULD RESULT IN DEATH OR SERIOUS INJURY.
091033
IMPROPERLY GROUNDED HEATING UNIT CAN CAUSE
ELECTRIC SHOCK OR ElECTROCUTION.
MAKE SURE LOADER IS GROUNDED WHEN USING
ELECTRIC HEATER.
FAILURE TO HEED WILL RESULT IN DEATH OR
SERIOUS INJURY.
093484
(CONTINUED)
ROTATING COMPONENTS CAN CUT HANDS.
FAILURE TO HEED WILL RESULT IN DEATH
OR SERIOUS INJURY.
091050
091050
PRESSURE CAP
072798
13

14
SAFETY
MAINTAIN SAFE CLEARANCE FROM
ELECTRIC POWER LINES AND AVOID
CONTACT WITH ANY ELECTRICALLY
CHARGED CONDUCTOR.
CONTACT WITH ELECTRICAL POWER
SOURCE CAN RESULT IN ELECTRICAL
SHOCK OR ELECTROCUTION.
FAILURE TO HEED WILL RESULT IN
DEATH OR SERIOUS INJURY.
093202
KEEP ALL GUARDS AND SHIELDS IN PLACE.
KEEP HANDS, FEET, AND ARMS INSIDE ENCLOSURE WHilE ENGINE AND
MACHINE ARE OPERATING AND AWAY FROM POWER DRIVEN COMPONENTS.
KEEP CHILDREN AND BYSTANDERS OFF AND AWAY FROM MACHINE.
DO NOT WEAR LOOSE OR BAGGY CLOTHING WHILE OPERATING DR
SERVICING MACHINE.
WEAR PROPER PERSONAL SAFETY GEAR CALLED FOR BY JOB OR
CONDITIONS.
DO NOT START ENGINE OR OPERATE LOADER OR ATTACHMENT
CONTROLS FROM ANY POSITION OTHER THAN PROVIDED.
DO NOT OPERATE MACHINE IN ENCLOSED AREA WITHOUT PROPER
VENTILATION.
TRAVEL SLOWLY OVER ROUGH TERRAIN WHEN RAISING LIFT ARM AND
APPROACHING DUMP AREA. NEVER MAKE SHARP MANUEVERS WITH
LIFT ARMS RAISED.
BEFORE LEAVING OPERATOR'S SEAT, LOWER LIFT ARMS AGAINST
FRAME, STOP ENGINE AND ENGAGE PARKING BRAKE.
IF LIFT ARMS MUST BE LEFT IN RAISED POSTlON, ALWAYS
INSTALL LIFT ARM LOCK.
DO NOT CHANGE BUCKET WITH LIFT ARMS RAISED.
ESCAPING flUID UNDER PRESSURE CAN BE INVISIBLE AND CAN
PENETRATE SKIN. DO NOT USE HANDS TO SEARCH FOR LEAKS.
RELIEVE PRESSURE PRIOR TO DISCONNECTING. HYDRAULIC LINES
AND COMPONENTS CAN BE HOT. DO NOT TOUCH.
NEVER SMOKE WHILE FIlliNG FUEL OR WORKING ON FUEl OR
HYDRAULIC SYSTEM.
FAILURE TO HEED COULD RESULT IN DEATH OR SERIOUS INJURY.
093474
(CONTINUED)

THE OWNER IS RESPONSIBLE FOR MAKING IN·
FORMATION AVAILABLE TO THE OPERATOR ON
THE SAFE USE AND PROPER MAINTENANCE OF
THIS MACHINE.
DO NOT START, OPERATE, OR WORK ON THIS
MACHINE UNTIL YOU READ AND UNDERSTAND
THE CONTENTS OF THE OPERATOR'S MANUAl.
IF YOU HAVE QUESTIONS ON OPERATION
ADJUSTMENT OR MAINTENANCE OF THIS
MACHINE OR NEED AN OPERATOR'S MANUAL,
OR IF ANY DECALS ARE NOT READABLE,
CONTACT YOUR GEHL DEALER OR
GEHL COMPANY, WEST BEND, WISCONSIN 53095
MODEL AND SERIAL NUMBERS WILL BE
REQUIRED.
FAILURE TO HEED COULD RESULT IN DEATH OR
SERIOUS INJURY.
DO NOT WORK UNDER LIFT ARMS WHEN
RAISED UNLESS SUPPORTED BY LIFT ARM
STOP WITH ENGINE STOPPED.
REMOVING HOSES OR COMPONENT FAILURE
CAN CAUSE LIFT ARMS TO DROP.
FAILURE TO HEED WILL RESULT IN DEATH OR
SERIOUS INJURY.
(CONTINUED)
093367
091035
15

16
BE SURE SAFETY LOCK IS SECURELY ENGAGED
BEFORE WORKING UNDER OVERHEAD GUARD.
FAILURE TO HEED COULD RESULT IN DEATH OR
SERIOUS INJURY.
093477
F
(CONTINUED)
129133

ROTATING OR HOT COMPONENTS CAN CAUSE
INJURY
KEEP ENGINE COVER CLOSED WHilE ENGINE
IS RUNNING
fAILURE TO HEED COULD RESULT IN DEATH
OR SERIOUS iNJURY
(CONTINUED)
129130
129130
GAS-CHARGED SPRING
CYLINDERS ARE USED
ON THIS MACHINE.
SEE OPERATOR'S
MANUAL FOR
LOCATIONS.
CYLINDERS HAVE
HIGH INTERNAL
PRESSURE. DO NOT
DISASSEMBLE.
DISASSEMBLY COULD
RElEASE PARTS WITH
GREAT FORCE.
FAILURE TO HEED
COULD RESULT IN
DEATH OR SERIOUS
INJURY.
122745
REMOVING HOSES OR COMPONENT FAILURE CAN CAUSE LIFT ARMS TO OROP
USE MECHANICAL LOCK WHEN LEAVING LIFT ARM IN RAISEO POSITION FOR SERVICE
FAILURE TO HEED WILL RESULT IN DEATH OR SERIOUS INJURY
129132
17

CHAPTER 5
CONTROLS & SAFETY EQUIPMENT
CAUTION
Become familiar with and know how to use
ALL safety devices and controls on the
Skid Loader BEFORE attempting to
operate it. Know how to stop Loader
operation BEFORE starting it. This GEHL
Skid Loader is designed and intended to
be used ONLY with a GEHL Company
Attachment or a GEHL Company approved
accessory or referral attachment. The
GEHL Company can NOT be responsible
for operator safety if the Loader is used
with a non-approved attachment.
GUARDS & SHIELDS
Whenever possible and without affecting Loader
operation, Guards and Shields are used to protect
potentially hazardous areas. In many places, Decals
are also provided to warn
of potential dangers and/or
to display special operating procedures.
WARNING
Read and thoroughly understand ALL
Safety Decals on the Loader BEFORE
attempting to operate it. Do NOT attempt to
operate the Loader unless ALL factory
installed Guards and Shields are properly
secured in place.
18
CONTROLS
Your Loader could be equipped with either "Hand
& Foot" or "T-Bar" Controls.
Follow
instructions appropriate for your Loader
type.
Fig. 1
1. Accelerator Pedal
2. Hand Throttle
THROTTLE LEVER & ACCELERATOR
PEDAL (Fig. 1)
A right-hand controlled Throttle Lever is provided on
all models for adjusting the Engine RPM.
A
right-foot operated Accelerator Pedal is also
provided to control the Engine RPM to match
increased power requirements. The Pedal linkage is
spring-loaded to return to the adjusted hand-operated
Throttle setting.