Gemas Pool Control Mono Quick guide

POOL CONTROL MONO INSTALLATION AND INSTRUCTION
MANUAL

Prior Knowledge
We thankfull for your trust in us with your purchase of a GEMAS products.
Gemas is continuing to offer products that make pools healthier and more reliable by offering
new products to users with the policy of continuous development and improvement.
Pool Control Mono allows the pump, lamp and additional group of equipment used in the pool to set the
starting and closing times for the operation, allowing the equipment to automatically shut down in the case of
high or low current.
Settings
1- Pump, lights and additional equipment groups timing control settings
a. Start Time (operating):
The setting button is turned clockwise or counterclockwise until the opening led is turned to the
side to make the setting in the desired group. When the led turns on, the last set time is displayed on
the screen. Once the setting button is pressed, the minutes digit of the start time starts flashing.
While the minute is flashing, turn the setting dial clockwise or counterclockwise to set the desired
time. Each move of the button gives 5 minutes of change. Press the button once after setting the
desired time allows the setting to be completed and saved.
1. Pump On
1. Pump Off
2. Pump On
2. Pump Off
Light Group On
Light Group Off
Aux. Group On
Aux. Group Off
Manual On/Off
Button
Pump Operating
Status
Settings Button
Malfunction
Signal

b. Closing Time:
The setting button is turned clockwise or
counterclockwise until the closing led is turned to
the side to make the setting in the desired group.
When the led turns on, the last set time is
displayed on the screen. Once the setting button is
pressed, the minutes digit of the closing time starts
flashing. While the minute is flashing, turn the
setting dial clockwise or counterclockwise to set
the desired time. Each move of the button gives 5
minutes of change. Press the button once after
setting the desired time allows the setting to be
completed and saved.
2- Manual On/Off Button
When the equipment connected to the product is
operating, turning on the button until the led lights
on and then pressing the button, all equipment
connected to the product is turned off then pres
again and all euipments starts work. For operation
again automatically, the product needs to be
switched from manual control to automatic control
mode as described in chapter 4.
3- Pump Current
The current drawn by the pump can also be
monitored via the digital screen. A standart value is set
for this current, and if the current goes out of tolerance,
the product automatically closes the pump to protect the
pump. To set the current value, turn the button "CAL" on
the display until it comes out, then press the button.
After 1-1.5 minutes of product measurement, calibration
was completed and normal value was obtained. If the
current is out of tolerance, the product stops running the
pump.

4- Automatic - Manual operation
When the button is turned to “P.AUTO”, the pump is
switched to automatic mode. If the '' P.ON '' status is
present, the manual mode is switched and the automatic
mode is disabled. If the button is pressed when the ''
P.OFF '' status is present, the pump is manually turned
off and the automatic mode is disabled.
When the button is turned to “L.AUTO”, the light
group is switched to automatic mode. If the '' L.ON ''
status is present, the manual mode is switched and the
automatic mode is disabled. If the button is pressed
when the '' L.OFF '' status is present, the light group is
manually turned off and the automatic mode is disabled.
When the button is turned to “A.AUTO”, the
additional equpment group is switched to automatic
mode. '' A.ON '' status is present, the manual mode is
switched and the automatic mode is disabled. If the
button is pressed when the '' A.OFF '' status is present,
the pump is manually turned off and the automatic
mode is disabled.
5- Time Settings
Turn the button until "SETT" appears on the display. When "SETT" appears, the button is pressed
and the hour and minute appear on the screen; Minute digit is flashing. By turning the button, the
minutes are changed and the time is set, then the setting is saved by pressing the button again.