gen2 UP Guide

National Office 216-898-0080 Page | 1
www.gen2office.com
UP
tables & worksurfaces
(2-leg)
Installation and User Instructions

National Office 216-898-0080 Page | 2
www.gen2office.com
Step 1: INSTALL FEET AND MOUNTING BRACKETS TO LIFTING COLUMNS
• Use the provided machine screws.
• Fasten the machine screws b hand and tighten using an allen wrench.
NOTE Both sides of the mounting brackets do not have the same size
holes. The side with larger holes mounts to the lifting columns using the
machine screws. The side with smaller holes mounts to the UP- table using
wood screws. The machine screws do not fit through the smaller holes.

National Office 216-898-0080 Page | 3
www.gen2office.com
Step 2: INSTALL LIFTING COLUMN BASE ASSEMBLY TO THE UP-TABLE
• Use the provided wood screws.
• For UP-tables 60” and smaller – lifting column bases can be mounted at the
table’s edge or with slight overhang.
• For UP-tables larger than 60” – position lifting column bases 60” apart and
mount with the same overhang on both sides (centered).
Step 3: MOUNT CONTROL BOX AND HANDSET TO THE UP-TABLE
• Use the provided wood screws.
• The Control Box can be mounted an where on the underside of the UP-
table. Mounting the control box tucked behind the left or right lifting
column is most ideal.
• The handset can be mounted an where on the underside of the UP-table’s
front edge.
Step 4: CONNECT CABLES
• Connect lifting column bases and handset to the control box using the
provided cables as per the following diagrams. Adhesive backed cable clips
can be used to secure the cables and prevent sagging. Once clips are
positioned, then secure with wood screws.

National Office 216-898-0080 Page | 4
www.gen2office.com

National Office 216-898-0080 Page | 5
www.gen2office.com

National Office 216-898-0080 Page | 6
www.gen2office.com
Step 5: TURN THE ASSEMBLED UP-TABLE RIGHT-SIDE UP
• Use two people and proper lifting techniques to prevent injur .
• Adjust the leveling glides on the feet as needed to ensure the UP-table is
level.
• Plug the power cord into a 110V outlet.
• Make sure obstacles are not in the UP-table’s path.
• Make sure cords have enough slack to accommodate the change of height.
Step 6: INITIALIZE UP-TABLE – RESET PRIOR TO USE
• Push and hold the DOWN button on the handset until the UP-table reaches
it’s lowest height. Release the DOWN button.
• Push and hold the DOWN button for approximatel 5 seconds. Release the
DOWN button. Continue doing this until the UP-table slightl rises and
stops. When the UP-table slightl rises and stops the RESET procedure is
complete.
• To program the presets – use the UP/DOWN buttons to reach our desired
height, then press M followed b the preset ou want to save (1 – 4).
TRO BLESHOOTING
• If the UP-table is not functioning properl it ma need to be RESET. Follow
the RESET procedure outlined in Step 6.
• If the handset displa s an error code check that all connections are secure
and perform the above RESET procedure.
• If the handset displa s HOT, let the UP-table cool down for 20 minutes.
• If the UP-table is not level adjust the leveling glides on the feet.
NOTE The UP- table might need RESET if ever un lugged or if any connections
are disconnected.
TECHNICAL SPECIFICATIONS
• Height Range 24.4 – 49.6”
• Speed 1.5”/second
• Weight Limit 350 lbs.
• Duty Cycle 10% maximum; 2-minutes ON/18-minutes OFF

National Office 216-898-0080 Page | 7
www.gen2office.com
**SAFETY AND WARNINGS**
• Inappropriate use of this product ma cause propert or bodil injur .
• Not intended for use b children or persons who require supervision.
• Make sure obstacles are not in the UP-table’s path and all cords are of
appropriate length.
• Do not open an of the UP-table’s components – Risk of electric shock.
• Risk of Pinch Point – the UP-table should have a minimum of a 1” gap
around all sides.
• Do not sit, stand, or crawl on or under the UP-table.
• Keep all electrical components awa from liquids.
LIABILITY: The manufacturer does not accept warrant /liabilit claims for
damages caused b improper use.

National Office 216-898-0080 Page | 8
www.gen2office.com
15655 Brookpark Road
Cleveland, Ohio 44142