Genaray LED-6800 User manual

USER MANUAL
LED-6800
256 LED ON-CAMERA LIGHT

LED-6800
INTRODUCTION
Thank you for choosing the Genaray LED-6800
On-Camera Light. This product will provide you with
powerful, portable and dependable illumination that
can be used in a variety of settings. Featuring a super-
bright 256 LED lamp count, 5800K color temperature,
flicker-free, dimmable features and two removable
filters with advanced light dispersion capabilities,
the Genaray LED-6800 On-Camera Light is the
perfect choice for professional photographers and
videographers alike.
LED-6800 - USER MANUAL
2

· Lightweight Design With
Powerful 256 Lamp Count
· Long Profile Provides Wider
Angle Of Coverage
· Removable Diffuser & 3200K
Warming Filter
· Low Battery Power Warning Light
· Vertically Stackable
· 256 LED Light
· Slide-In Diffuser
· Slide-In Warming Filter
· NP-F750 Battery
· AC/DC Battery Charger
· AC Adapter
· Ball Head Mount
· Manual
KEY
FEATURES
PRODUCT
CONTENTS
LED-6800 - USER MANUAL
3
Features

SAFETY
WARNINGS
· Do not attempt to disassemble,
repair or perform any unauthorized
modifications on device
· Do not handle with wet hands,
immerse in liquids or expose to water
and rain; electric shock or fire may
result
· Device contains small parts which
may pose a choking hazard; keep out
reach of children
· Do not operate device in presence of
flammable gas or vapors
· Do not use product if it emits smoke
or a strange odor; disconnect power
source immediately to avoid personal
injury and contact place of purchase
· Observe caution when handling
batteries; only use batteries approved
by the manufacturer of this product
· Batteries are prone to leakage when
fully discharged; to avoid damaging
product be sure to remove batteries
when leaving product unattended
· Do not intentionally stare or gaze at
LED-6800 - USER MANUAL
4
saFety Warnings

LED light panel for prolonged periods
while device is on
· Do not cover the ventilation grille
found at the rear of device when in
operation and ensure light is cool
before storing
· Do not use or leave device in
conditions of extreme heat, severe
cold or high humidity
· Unit will display a decrease in
brightness when the battery runs
low; be sure to replace battery when
necessary to avoid affecting recording
quality
· When cleaning the device, use only a
mild detergent solution and quickly
wipe dry with a soft cloth
· Please dispose of used batteries,
packaging and old devices in
accordance with appropriate
environmental regulations
LED-6800 - USER MANUAL
5
saFety Warnings

Filter
Clasps
LED
Array Included
Ball Head
Mount
Cold Shoe Mount
1/4 20
Threading Mount
LED-6800 - USER MANUAL
6
PRODUCT
OVERVIEW

Battery
Mounting
Area
Battery
Release
Button Dimming
Knob
Power
Knob Interlocking
Expansion Slot
LED-6800 - USER MANUAL
7
PrODuCt OvervieW
Low
Battery
Level
Warning
Light
DC Input
Expansion
Slot Release
Tab

MOUNTING LIGHT
UNIT DIRECTLY ON
CAMERA OR TRIPOD
LED-6800 - USER MANUAL
8
· Begin by positioning light directly atop
camera or video camera
· Slide cold shoe mounting into shoe of
camera
· For tripod installation, simply insert 1/4 20
screw found on tripod head into the 1/4 20
threading mount found on bottom of unit;
then tighten securely
Light can also be fastened
to included ball head mount,
which can then be installed on
cold shoe found on cameras
or similar devices; see ball
head mounting instructions
Note
MOUNTING LIGHT
UNIT ON BALL HEAD
MOUNT
· Included ball head mount is designed to
provide user with a 180° tilt/360° rotating
angle feature that can be used on both
cameras and other devices featuring a cold
shoe
· Begin by inserting 1/4 20 screw found atop ball
head mount into the 1/4 20 threading found on
bottom of LED light unit and fasten securely
· Tighten adjustment locking knob so light
unit does not wobble during remainder of
mounting process
· Ensure cold shoe foot is firmly secured to ball
head mount device and loosen locking collar
found on base of ball head device
· Slide entire male cold shoe into female cold
shoe of camera or other mounting device; then
fasten locking collar securely
instruCtiOns

INTERLOCKING
WITH OTHER
LED DEVICES
LED-6800 - USER MANUAL
9
· Slide cold shoe mounting into interlocking
expansion slot of another compatible
Genaray LED light device
· To separate stacked units, press down on
the release tab found at the bottom of the
expansion slot to allow the cold shoe of the
other unit to slide out
· Compatible Genaray LED light devices can
be mounted atop one another in a stacked
vertical format for increased illumination
· Loosen adjustment locking knob by
twisting counterclockwise and rotate ball
head mount to position light at desired
angle; twist locking knob clockwise to hold
light unit firmly in position
Cold shoe mount can also
be removed to reveal an
integrated1/4 20 threading
mount
· To reveal ball head mount's integrated 1/4
20 threading mount for fastening to tripod,
twist locking ring resting above cold shoe
counterclockwise until entire shoe comes
out; insert 1/4 20 screw found on tripod
head into the 1/4 20 threading mount; then
tighten securely
Note
instruCtiOns

LED-6800 - USER MANUAL
10
POWERING
DEVICE
ADJUSTING
FEATURES
· Begin by holding fully-charged battery in
position over mounting area, leaving only
a small gap between conductor contacts
found on battery and metal prongs found
on unit
· Push battery down and lock into place by
sliding it inwards along grooves until an
audible click is heard
· The power port found on rear of monitor
connects directly to the AC/DC power
adapter and can provide continuous power
in the event that the battery is low
· Turn the power dial to the right until it
clicks into the on position
· Rechargeable battery can be removed
by firmly pushing down on the battery
release button and sliding the battery to
the side until it disengages
· To adjust the flicker-free dimmable
features, simply rotate the dimming
wheel until desired effect is achieved
· To install the 3200K warming or the soft
diffusion filter, align filter with clasps
found on edge of LED panel; ensure that
filter tab is facing downwards and slide
filter alongside clasps; gently snap filter
in place
instruCtiOns