Genelec 8020A User manual

Monitoring Line Specifications
6010A and 8000 Series
6010A 8020A 8030A 8040A 8050A
Drivers
Bass
Treble
Both drivers are magnetically shielded
76 mm (3”)
19 mm (3/4") metal dome
105 mm (4”)
19 mm (3/4") metal dome
130 mm (5")
19 mm (3/4") metal dome
165 mm (6.5")
19 mm (3/4") metal dome
205 mm (8")
25 mm (1") metal dome
Lower cut-off frequency, –3 dB
Upper cut-off frequency, –3 dB
Free field frequency response of system
≤73 Hz
≥21 kHz
74 Hz – 18 kHz (± 2.5 dB)
≤65 Hz
≥21 kHz
66 Hz – 20 kHz (± 2.5 dB)
≤55 Hz
≥21 kHz
58 Hz – 20 kHz (± 2 dB)
≤45 Hz
≥21 kHz
48 Hz – 20 kHz (± 2 dB)
≤35 Hz
≥21 kHz
38 Hz – 20 kHz (± 2 dB)
Maximum short term sine wave acoustic output @
1 m on axis in half space, averaged from
100 Hz to 3 kHz
≥93 dB SPL ≥95 dB SPL ≥100 dB SPL ≥105 dB SPL ≥110 dB SPL
Self generated noise level in free field @ 1 m on
axis (A-weighted)
≤5 dB ≤10 dB ≤10 dB ≤10 dB ≤10 dB
Harmonic distortion (at given SPL@ 1 m on axis)
Frequency:
@ 80 dB
70...400 Hz < 3 %
> 400 Hz < 0.5 %
@ 85 dB
50...100 Hz < 3 %
> 100 Hz < 0.5 %
@ 85 dB
50...100 Hz < 2 %
> 100 Hz < 0.5 %
@ 90 dB
50...100 Hz < 2 %
> 100 Hz < 0.5 %
@ 90 dB
50...100 Hz < 2 %
> 100 Hz < 0.5 %
Crossover
Crossover frequency
Treble Tilt control (2 dB steps)
Desktop Low Frequency control
Bass Roll-Off control
(2 dB steps, 8020A & 8030A – 6 dB step)
Bass Tilt control (2 dB steps)
3 kHz
n/a
–4 dB @ 200 Hz
n/a
0 to –6 dB @ 100 Hz
3 kHz
0 to –2 dB @ 15 kHz
n/a
–6 dB @ 85 Hz
0 to –6 dB @ 100 Hz
3 kHz
0 to –2 dB @ 15 kHz
n/a
–6 dB @ 85 Hz
0 to –6 dB @ 100 Hz
3 kHz
+2 to –4 dB @ 15 kHz & Mute
–4 dB @ 160 Hz
0 to –6 dB @ 45 Hz
0 to –6 dB @ 100 Hz & Mute
1.8 kHz
+2 to –4 dB @ 15 kHz & Mute
–4 dB @ 160 Hz
0 to –6 dB @ 35 Hz
0 to –6 dB @ 100 Hz & Mute
Bass amplifier output power
Treble amplifier output power
(Long term output power is limited by driver
protection circuitry)
12 W (8 Ohm load)
12 W (8 Ohm load)
20 W (8 Ohm load)
20 W (8 Ohm load)
40 W (8 Ohm load)
40 W (8 Ohm load)
90 W (8 Ohm load)
90 W (8 Ohm load)
150 W (6 Ohm load)
120 W (8 Ohm load)
Signal to Noise ratio, referred to full output
Bass
Treble
≥95 dB
≥95 dB
≥95 dB
≥95 dB
≥100 dB
≥100 dB
≥100 dB
≥100 dB
≥100 dB
≥100 dB
Power consumption
Idle
Full output
5 VA
35 VA
5 VA
50 VA
10 VA
80 VA
10 VA
110 VA
10 VA
170 VA
Dimensions
Height
Width
Depth
Height with Iso-Pod™
181 mm (71/8”)
121 mm (43/4")
114 mm (41/2”)
195 mm (711/16”)
226 mm (87/8”)
151 mm (6")
142 mm (55/8”)
242 mm (91/2”)
285 mm (111/4")
189 mm (77/16")
178 mm ( 71/16")
299 mm (1113/16")
350 mm (1313/16")
237 mm (93/8")
223 mm (813/16")
365 mm (143/8")
433 mm (171/16")
286 mm (111/4")
278 mm (1015/16")
452 mm (1713/16")
Weight 1.4 kg (3.1 lb) 3.7 kg (8.1 lb) 5.6 kg (12.3 lb) 8.6 kg (18.9 lb) 12.7 kg (28 lb)
Detailed Data Sheets of all Genelec models,
Quick Setup Guides and lots of other useful
information can be downloaded at
www.genelec.com

1032A 1037C 1038B 1038BC
Drivers
Bass
Midrange
Treble
All drivers are magnetically shielded
254 mm (10")
n/a
25 mm (1") metal dome
305 mm (12”)
130 mm (5”)
25 mm (1") metal dome
385 mm (15”)
130 mm (5")
25 mm (1") metal dome
2 x 254 mm (10")
130 mm (5")
25 mm (1") metal dome
Lower cut-off frequency, –3 dB
Upper cut-off frequency, –3 dB
Free field frequency response of system
≤40 Hz
≥22 kHz
42 Hz – 21 kHz (± 2.5 dB)
≤35 Hz
≥22 kHz
37 Hz – 21 kHz (± 2.5 dB)
≤33 Hz
≥20 kHz
35 Hz – 20 kHz (± 2.5 dB)
≤33 Hz
≥20 kHz
35 Hz – 20 kHz (± 2.5 dB)
Maximum peak acoustic output per pair
at given distance with music material
≥124 dB SPL @ 1 m ≥ 123 dB SPL @ 2 m ≥124 dB SPL @ 2 m ≥124 dB SPL @ 2 m
Maximum short term sine wave acoustic
output on axis in half space, averaged from
100 Hz to 3 kHz
≥113 dB SPL @ 1 m ≥116 dB SPL @ 1 m ≥120 dB SPL @ 1 m ≥120 dB SPL @ 1 m
Self generated noise level in free field
on axis (A-weighted)
≤10 dB @ 1 m ≤15 dB @ 2 m ≤15 dB @ 2 m ≤15 dB @ 2 m
Harmonic distortion @ 1 m on axis at
given frequency range and SPL
@ 90 dB SPL
50…100 Hz < 1 %
> 100 Hz < 0.5 %
@ 95 dB SPL
≤100 Hz < 1 %
> 100 Hz < 0.5 %
@ 95 dB SPL
50…100 Hz < 1 %
> 100 Hz < 0.5 %
@ 95 dB SPL
50…100 Hz < 1 %
> 100 Hz < 0.5 %
Crossover
Crossover frequencies
Treble Tilt control in 2 dB steps
Level control in 1 dB steps
Bass
Midrange
Treble
Bass Roll-Off control in 2 dB steps
Bass Tilt control in 2 dB steps
1.8 kHz
+2 to –4 dB @ 15 kHz & Mute
n/a
n/a
n/a
0 to –8 dB @ 40 Hz
0 to –6 dB @ 100 Hz & Mute
420 Hz, 3.2 kHz
n/a
0 to -6 dB & Mute
0 to -6 dB & Mute
0 to -6 dB & Mute
0 to -8 dB @ 35 Hz
0 to -8 dB @ 80 Hz
410 Hz, 3 kHz
n/a
0 to -6 dB & Mute
0 to -6 dB & Mute
0 to -6 dB & Mute
0 to -8 dB @ 33 Hz
0 to -8 dB @ 80 Hz
410 Hz, 3 kHz
n/a
0 to -6 dB & Mute
0 to -6 dB & Mute
0 to -6 dB & Mute
0 to -8 dB @ 33 Hz
0 to -8 dB @ 80 Hz
Bass amplifier short term output power
Midrange amplifier short term output power
Treble amplifier short term output power
(Long term output power is limited by
driver protection circuitry)
180 W (4 Ohm load)
n/a
120 W (8 Ohm load)
180 W (4 Ohm load)
120 W (8 Ohm load)
120 W (8 Ohm load)
400 W (8 Ohm load)
120 W (8 Ohm load)
120 W (8 Ohm load)
2 x 200 W (8 Ohm load)
120 W (8 Ohm load)
120 W (8 Ohm load)
Signal to Noise ratio, referred to full output
Bass
Midrange
Treble
≥100 dB
n/a
≥100 dB
≥100 dB
≥100 dB
≥100 dB
≥100 dB
≥100 dB
≥100 dB
≥100 dB
≥100 dB
≥100 dB
Power consumption
Idle
Full output
50 VA
200 VA
50 VA
300 VA
60 VA
500 VA
60 VA
500 VA
Loudspeaker dimensions
Height
Width
Depth
Amplifier dimensions
Height
Width
Depth
495 mm (191/2")
320 mm (125/8")
290 mm (117/16")
Integrated in the
loudspeaker cabinet
680 mm (263/4”)
400 mm (153/4)
380 mm (1415/16)
Integrated in the
loudspeaker cabinet
810 mm (317/8")
480 mm (187/8")
420 mm (169/16")
Integrated in the
loudspeaker cabinet
350 mm (133/4")
950 mm (373/8")
453 mm (177/8")
530 mm (207/8")
480 mm (187/8")
113 mm (47/16")
Weight
Loudspeaker
Amplifier
21.7 kg (48 lb) 37 kg (82 lb) 60 kg (130 lb) 60 kg (130 lb)
14 kg (31 lb)
1032A and Tri-amplified Monitors

Main Monitors
1034B 1034BC 1039A 1035B 1036A
Drivers
Bass
Midrange
Treble
All drivers are magnetically shielded
2 x 305 mm (12”)
130 mm (5”)
25 mm (1") metal dome
2 x 305 mm (12”)
130 mm (5”)
25 mm (1") metal dome
2 x 385 mm (15”)
130 mm (5”)
25 mm (1") metal dome
2 x 385 mm (15”)
2 x 130 mm (5”)
25 mm (1")
compression driver
2 x 460 mm (18”)
2 x 130 mm (5”)
25 mm (1")
compression driver
Lower cut-off frequency, –3 dB
Upper cut-off frequency, –3 dB
Free field frequency response of system
≤32 Hz
≥20 kHz
33 Hz – 20 kHz (± 2.5 dB)
≤32 Hz
≥20 kHz
33 Hz – 20 kHz (± 2.5 dB)
≤29 Hz
≥20 kHz
31 Hz – 20 kHz (± 2.5 dB)
≤29 Hz
≥22 kHz
30 Hz – 20 kHz (± 2.5 dB)
≤19 Hz
≥22 kHz
21 Hz – 20 kHz (± 2.5 dB)
Maximum peak acoustic output per pair @ 2 m
distance with music material
≥125 dB SPL ≥125 dB SPL ≥126 dB SPL ≥136 dB SPL ≥136 dB SPL
Maximum short term sine wave acoustic output
@ 1 m on axis in half space, averaged from
100 Hz to 3 kHz
≥123 dB SPL ≥123 dB SPL ≥126 dB SPL ≥131 dB SPL ≥131 dB SPL
Self generated noise level in free field @ 2 m on
axis (A-weighted)
≤15 dB ≤15 dB ≤15 dB ≤20 dB ≤20 dB
Harmonic distortion (@ 95 dB SPL@ 1 m on
axis) at given frequency range
50...200 Hz < 1 %
200 Hz...10 kHz < 0.5 %
50...200 Hz < 1 %
200 Hz...10 kHz < 0.5 %
50...200 Hz < 1 %
200 Hz...10 kHz < 0.5 %
50...200 Hz < 1 %
200 Hz...4 kHz < 0.5 %
> 4 kHz < 3 %
50...200 Hz < 1 %
200 Hz...4 kHz < 0.5 %
> 4 kHz < 3 %
Crossover
Crossover frequencies
Level control in 1 dB steps
Bass
Midrange
Treble
Bass Roll-Off control in 2 dB steps
Bass Tilt control in 2 dB steps
Treble Roll-Off control in 1 dB steps
400 Hz, 3.2 kHz
from 0 to -6 dB & Mute
from 0 to -6 dB & Mute
from 0 to -6 dB & Mute
from 0 to -8 dB @ 32 Hz
from 0 to -8 dB @ 50 Hz
n/a
400 Hz, 3.2 kHz
0 to -6 dB & Mute
0 to -6 dB & Mute
0 to -6 dB & Mute
0 to -8 dB @ 32 Hz
0 to -8 dB @ 50 Hz
n/a
400 Hz, 3.2 kHz
0 to -6 dB & Mute
0 to -6 dB & Mute
0 to -6 dB & Mute
0 to -8 dB @ 29 Hz
0 to -8 dB @ 50 Hz
n/a
400 Hz, 3.5 kHz
0 to -6 dB & Mute
0 to -6 dB & Mute
0 to -6 dB & Mute
0 to -8 dB @ 30 Hz
0 to -8 dB @ 50 Hz
+1 to -3 dB @ 15 kHz
400 Hz, 3.5 kHz
0 to -6 dB & Mute
0 to -6 dB & Mute
0 to -6 dB & Mute
0 to -8 dB @ 30 Hz
0 to -8 dB @ 50 Hz
+1 to -3 dB @ 15 kHz
Bass amplifier short term output power
Midrange amplifier short term output power
Treble amplifier short term output power
(Long term output power is limited by driver
protection circuitry)
2 x 400 W (8 Ohm load)
350 W (8 Ohm load)
120 W (8 Ohm load)
2 x 400 W (8 Ohm load)
350 W (8 Ohm load)
120 W (8 Ohm load)
2 x 400 W (8 Ohm load)
350 W (8 Ohm load)
120 W (8 Ohm load)
2 x 1100 W (8 Ohm load)
600 W (4 Ohm load)
300 W (8 Ohm load)
2 x 1100 W (8 Ohm load)
600 W (4 Ohm load)
300 W (8 Ohm load)
Signal to Noise ratio, referred to full output
Bass
Midrange
Treble
≥100 dB
≥100 dB
≥100 dB
≥100 dB
≥100 dB
≥100 dB
≥100 dB
≥100 dB
≥100 dB
≥101 dB
≥105 dB
≥106 dB
≥101 dB
≥105 dB
≥106 dB
Power consumption
Idle
Full output
70 VA
1000 VA
70 VA
1000 VA
70 VA
1000 VA
150 VA
3500 VA
150 VA
3500 VA
Loudspeaker dimensions
Height
Width
Depth
Amplifier dimensions
Height
Width
Depth
700 mm (279/16")
890 mm (35")
383 mm (151/16")
310 mm (123/16")
483 mm (19")
250 mm (913/16")
489 mm (191/4")
1210 mm (475/8")
412 mm (161/4")
310 mm (123/16")
483 mm (19")
250 mm (913/16")
820 mm (325/16")
1050 mm (415/16")
550 mm (215/8")
310 mm (123/16")
483 mm (19")
250 mm (913/16")
820 mm (325/16")
1105 mm (43½")
775 mm (30½")
755 mm (293/4")
483 mm (19")
370 mm (149/16")
960 mm (373/4")
1180 mm (461/2")
650 mm (255/8")
755 mm (293/4")
483 mm (19")
370 mm (149/16")
Weight
Loudspeaker
Amplifier
73 kg (161 lb)
30 kg (66 lb)
84 kg (185 lb)
30 kg (66 lb)
115 kg (253 lb)
30 kg (66 lb)
142 kg (313 lb)
71 kg (156 lb)
182 kg (401 lb)
71 kg (156 lb)

DSP Loudspeaker Systems
8240A 8250A 7260A 7270A 7271A
Drivers
Bass
Treble
All drivers are magnetically shielded
165 mm (6.5")
19 mm (3/4") metal
dome
205 mm (8")
25 mm (1") metal dome
254 mm (10”)
n/a
305 mm (12”)
n/a
2 x 305 mm (12”)
n/a
Free field frequency response of system 48 Hz - 20 kHz (± 1 dB) 38 Hz - 20 kHz (± 1 dB) 19 Hz - 100 Hz (± 3 dB) 19 Hz - 100 Hz (± 3 dB) 19 Hz - 100 Hz (± 3 dB)
Maximum peak SPL output per pair
on top of console @ 1 m with music material
≥ 115 dB SPL ≥ 120 dB SPL n/a n/a n/a
Maximum short term sine wave SPL output @ 1 m
on axis in half space, averaged as specified
(from 100 Hz to 3 kHz)
≥ 105 dB SPL
(from 100 Hz to 3 kHz)
≥ 110 dB SPL
(from 30 Hz to 85 Hz)
≥108 dB SPL
(from 30 Hz to 85 Hz)
≥112 dB SPL
(from 30 Hz to 85 Hz)
≥118 dB SPL
Crossover frequency 3 kHz 1.8 kHz n/a n/a n/a
Self generated noise level in free
field @ 1 m on axis (A-weighted)
≤10 dB ≤10 dB ≤15 dB ≤15 dB ≤15 dB
Harmonic distortion at 90 dB SPL @ 1 m on axis
Freq: 50…100 Hz
> 100 Hz
< 2 %
< 0.5 %
< 2 %
< 0.5 %
n/a
n/a
n/a
n/a
n/a
n/a
Harmonic distortion at given dB SPL @ 1 m in
half space
2nd
3rd
n/a
n/a
n/a
n/a
@ 90 dB SPL
from 30 to 85 Hz
≤3 %
≤3 %
@ 95 dB SPL
from 30 to 85 Hz
≤3 %
≤3 %
@ 100 dB SPL
from 30 to 85 Hz
≤3 %
≤3 %
Input signal
Analog
AES/EBU (single wire and dual wire)
1 XLR female
1 XLR female
1 XLR female
1 XLR female
n/a
4 XLR female
n/a
4 XLR female
n/a
4 XLR female
Output / Thru signal
AES/EBU (single wire and dual wire) 1 XLR male 1 XLR male 4 XLR male 4 XLR male 4 XLR male
Digital audio
Word length
Sample rate
16 - 24 bits
32 - 192 kHz
16 - 24 bits
32 - 192 kHz
16 - 24 bits
32 - 192 kHz
16 - 24 bits
32 - 192 kHz
16 - 24 bits
32 - 192 kHz
Control network
Type
Connection
proprietary GLMTM
network
2 RJ45, CAT5 cables
proprietary GLMTM
network
2 RJ45, CAT5 cables
proprietary GLMTM
network
2 RJ45, CAT5 cables
proprietary GLMTM
network
2 RJ45, CAT5 cables
proprietary GLMTM
network
2 RJ45, CAT5 cables
GLMTM software frequency response adjustment *
Notch filters
Shelving filters
2 LF and 2 HF
2 LF and 2 HF
2 LF and 2 HF
2 LF and 2 HF
4 LF
n/a
4 LF
n/a
4 LF
n/a
System calibration * AutoCalTM, GLMTM
manual, Stand-alone
AutoCalTM, GLMTM
manual, Stand-alone
AutoCalTM, GLMTM
manual, Stand-alone
AutoCalTM, GLMTM
manual, Stand-alone
AutoCalTM, GLMTM
manual, Stand-alone
Bass amplifier output power
Treble amplifier output power
(Long term output power is limited by driver
protection circuitry)
90 W
90 W
150 W
120 W
120 W
n/a
250 W
n/a
500 W
n/a
Power consumption
Idle
Full output
14 VA
110 VA
17 VA
170 VA
15 VA
150 VA
21 VA
250 VA
36 VA
500 VA
Dimensions
Height
Width
Depth
Height with Iso-Pod™
350 mm (1313/16“)
237 mm (93/8“)
223 mm (813/16“)
365 mm (143/8“)
433 mm (171/16“)
286 mm (111/4“)
278 mm (1015/16“)
452 mm (1713/16“)
527 mm (203/4“)
462 mm (183/16“)
363 mm (145/16“)
n/a
625 mm (245/8“)
555 mm (217/8“)
490 mm (195/16“)
n/a
755 mm (293/4“)
803 mm (315/8“)
490 mm (195/16“)
n/a
Weight 9.4 kg (20.8 lb) 14.6 kg (32 lb) 27 kg (59 lb) 51 kg (112 lb) 82 kg (180 lb)
• GLMTM features connectivity for up to twenty-five 8200
series loudspeakers and up to five 7200 series
subwoofers
• EnablesmultiplecustomUserSetupswithallsettings
and functions able to be stored in GLMTM setup or
directly to each loudspeaker
• Step-by-stepWizardguidesuserthroughcomplete
cabling connections and speaker labeling
• RapidCablingsetupsformostcommonsystem
configurations
• ManualCablingsetupsforcustomizedsystem
configurations
• GroupsforbothChannelsandLoudspeakersmaybe
customized by User
• Solo/MutefunctionforallLoudspeakersandGroups
• Volumecontrolledviacomputer,3rdpartyUSBdeviceor
customer console
• VideoDisplayCompensationforinherentvideodelaysin
digital video devices
• GLMTM provides interface to AutoCal™ automated
acoustical self-calibration algorithm
• GLMTM supports Windows XP and Mac OS X operating
systems
• Supportforupto24 (AES/EBU single-wire) or 12
(analog, AES/EBU dual-wire) audio channels
• GLMTM supports Windows XP and Mac OS X operating
systems
Major components included:
• GLMTM interface device
• 8200A Calibration microphone and holder
•USB cable
•Measurement signal cable
• Software CD
•System Operating Manual
Genelec Loudspeaker Manager™
(GLM™) Software Kit
GLMTM Multiroom Expansion Kit
Major components included:
• GLMTM interface device
• GLM network cable
•USB cable
* The notch and shelving filters adjustments, AutoCalTM and GLMTM manual system calibration features are part of the Genelec Loudspeaker Manager (GLMTM) software

GLM.SE DSP System SE7261A Subwoofer and 8130A Digital Input Monitor
8130A SE7261A
Drivers
Bass
Treble
All drivers are magnetically shielded
130 mm (5”)
19 mm (3/4") metal dome
254 mm (10”)
n/a
Free field frequency response of system 58 Hz - 20 kHz (± 2 dB) 19 Hz - 100 Hz (± 3 dB)
Maximum peak SPL output per pair
on top of console @ 1 m with music material
≥ 108 dB SPL n/a
Maximum short term sine wave SPL output @ 1 m
on axis in half space, averaged as specified
(from 100 Hz to 3 kHz)
≥ 100 dB SPL
(from 30 Hz to 85 Hz)
≥108 dB SPL
Crossover frequency 3 kHz n/a
Self generated noise level in free
field @ 1 m on axis (A-weighted)
≤10 dB ≤15 dB
Harmonic distortion at 85 dB SPL @ 1 m on axis
Freq: 50…100 Hz
> 100 Hz
< 2 %
< 0.5 %
n/a
n/a
Harmonic distortion at given dB SPL @ 1 m in
half space
2nd
3rd
n/a
n/a
@ 90 dB SPL
from 30 to 85 Hz
≤3 %
≤3 %
Input signal
Analog
AES/EBU (single wire)
1 XLR female
1 XLR female
Single dual acting
connector
n/a
4 XLR female
Output / Thru signal
AES/EBU (single wire) 1 XLR male 4 XLR male
Digital audio
Word length
Sample rate
16 - 24 bits
32 - 192 kHz
16 - 24 bits
32 - 192 kHz
Control network
Type
Connection
n/a proprietary GLMTM
network
2 RJ45, CAT5 cables
GLMTM software frequency response adjustment *
Notch filters 2 (at the high pass filters of
the SE7261A)
4 LF
System calibration * AutoCalTM, GLM.SETM
manual, DIP switches
AutoCalTM, GLM.SETM
manual, Stand-alone
Bass amplifier output power
Treble amplifier output power
(Long term output power is limited by driver
protection circuitry)
40 W
40 W
120 W
n/a
Power consumption
Idle
Full output
15 VA
80 VA
15 VA
150 VA
Dimensions
Height
Width
Depth
Height with Iso-Pod™
285 mm (111/4”)
189 mm (77/16”)
178 mm ( 71/16”)
299 mm (1113/16”)
527 mm (203/4“)
462 mm (183/16“)
363 mm (145/16“)
n/a
Weight 5.6 kg (12.3 lb) 27 kg (59 lb)
(GLM.SE™) Small Environment DSP
System Software
• GLM.SE™providesconnectivityforoneSE7261ADSP
subwoofer combined with up to eight 8130A digital input
loudspeakers
• EnablesmultiplecustomUserSetupswithallsettings
and functions able to be stored in GLM.SE™ setup or
directly to the SE7261A subwoofer
• Step-by-stepWizardguidesuserthroughcomplete
cabling connections and loudspeaker labeling
• RapidCablingsetupsformostcommonsystem
configurations
• ManualCablingsetupsforcustomizedsystem
configurations
• GroupsforbothChannelsandLoudspeakersmaybe
customized by User
• Solo/MutefunctionforallLoudspeakersandGroups
• Volumecontrolledviacomputer,3rdpartyUSBdevice
or customer console
• VideoDisplayCompensationforinherentvideodelays
in digital video devices
• GLM.SETM supports Windows XP and Mac OS X
operating systems
• GLM.SE™providesinterfacetoAutoCal™automated
acoustic self-calibration algorithm
Major components included:
• GLMTM interface device
• 8200A Calibration microphone and holder
•USB cable
•Measurement signal cable
• Software CD
•System Operating Manual

Active Subwoofers
5040A 7050B 7060B 7070A 7071A 7073A
Driver 165 mm (61/2”) 205 mm (8”) 254 mm (10”) 305 mm (12”) 2 x 305 mm (12”) 4 x 305 mm (12”)
Free field frequency response 35 - 85 Hz (±3 dB) 25 - 85 Hz (±3 dB) 19 - 85 Hz (±3 dB) 19 - 85 Hz (±3 dB) 19 - 85 Hz (±3 dB) 19 - 85 Hz (±3 dB)
Maximum short term sine wave SPL output @ 1 m
in half space
≥98 dB
averaged from 40 to 85 Hz
≥100 dB
averaged from 30 to 85 Hz
≥108 dB
averaged from 30 to 85 Hz
≥ 112 dB
averaged from 30 to 85 Hz
≥118 dB
averaged from 30 to 85 Hz
≥124 dB
averaged from 30 to 85 Hz
Self generated noise level in free field @ 1 m on
axis (A-weighted)
≤15 dB ≤15 dB ≤15 dB ≤15 dB ≤15 dB ≤15 dB
Harmonic distortion @ 1 m on axis in half space
Frequency
2nd
3rd
@ 85 dB SPL
30 to 85 Hz
≤4 %
≤ 1 %
@ 90 dB SPL
30 to 85 Hz
≤4 %
≤ 1 %
@ 95 dB SPL
30 to 85 Hz
≤2 %
≤3 %
@ 95 dB SPL
30 to 85 Hz
≤3 %
≤3 %
@ 100 dB SPL
30 to 85 Hz
≤3 %
≤3 %
@ 105 dB SPL
30 to 85 Hz
≤ 2 %
≤2 %
Input channels
Output channels
Sum Out channel
5 + LFE (RCA)
3.5 mm stereo jack
5 (RCA, high pass filtered at
85 Hz)
n/a
5 + LFE (XLR)
5 (XLR, unfiltered)
n/a
6 + LFE (XLR)
6 (XLR, high pass filtered at
85 Hz)
1
6 + LFE (XLR)
6 (XLR, high pass filtered at
85 Hz)
1
6 + LFE (XLR)
6 (XLR, high pass filtered at
85 Hz)
1
6 + LFE (XLR)
6 (XLR, high pass filtered at
85 Hz)
1
Controls
Bass Roll-Off
Phase adjustment
Selectable LFE lowpass filtering 85/120 Hz
LFE sensitivity 0 / +10 dB
Bypass
Redirect function for LFE frequencies >85 Hz
Test tone for phase adjustment
Sum in mode
0 / -2 / -4 / -6 dB @ 35 Hz
0 / -90° / -180° / -270°
n/a
n/a
n/a
n/a
n/a
n/a
0 / -2 / -4 / -6 dB @ 26 Hz
0 / -90° / -180° / -270°
Yes
Yes
n/a
n/a
n/a
n/a
0 / -2 / -4 / -6 dB @ 20 Hz
0 / -90° / -180° / -270°
Yes
Yes
Yes
Yes
Yes
Yes
0 / -2 / -4 / -6 dB @ 20 Hz
0 / -90° / -180° / -270°
Yes
Yes
Yes
Yes
Yes
Yes
0 / -2 / -4 / -6 dB @ 20 Hz
0 / -90° / -180° / -270°
Yes
Yes
Yes
Yes
Yes
Yes
0 / -2 / -4 / -6 dB @ 20 Hz
0 / -90° / -180° / -270°
Yes
Yes
Yes
Yes
Yes
Yes
Amplifier short term output power 40 W 70 W 120 W 250 W 500 W 1000 W
Power consumption
Idle
Full output
7 VA
70 VA
11 VA
120 VA
15 VA
150 VA
15 VA
250 VA
30 VA
500 VA
60 VA
1000 VA
Dimensions
Height
Width
Depth
251 mm (97/8”)
Diameter 305 mm (12”)
410 mm (161/8”)
350 mm (133/4”)
319 mm (129/16”)
527 mm (203/4”)
462 mm (183/16”)
363 mm (145/16")
625 mm (245/8”)
555 mm (217/8”)
490 mm (195/16")
755 mm (293/4”)
803 mm (315/8”)
490 mm (195/16")
524 mm (205/8”)
1440 mm (5611/16”)
558 mm (22")
Weight 6.3 kg (13.9 lb) 18 kg (39.6 lb) 26 kg (57 lb) 50 kg (110 lb) 81 kg (178 lb) 120 kg (265 lb)
Detailed Data Sheets of all Genelec models,
Quick Setup Guides and lots of other useful
information can be downloaded at
www.genelec.com
Genelec document BBAGE031b. Copyright Genelec Oy 12.2008. All data subject to change without prior notice
International enquiries:
Genelec, Olvitie 5
FIN-74100, Iisalmi, Finland
Phone [phone]
Fax [phone]
Email [email protected]
In the U.S. please contact:
Genelec, Inc., 7 Tech Circle
Natick, MA 01760
USA
Phone [phone]
Fax [phone]
Email [email protected]
In Sweden please contact:
Genelec Sverige
Ellipsvägen 10B
P.O. Box 5521, S-141 05
Huddinge, Sweden
Phone [phone]
Fax [phone]
Email [email protected]
In China please contact:
Beijing Genelec Audio Co. Ltd.
Jianwai SOHO, Tower 12, Room 3304
39 East 3rd Ring Road
Chaoyang District
Beijing 100022, China
Phone [phone], Fax [phone]