General Mfg THE LITE 9032-7037 User manual

By: General Mfg., Inc.
1100 S. Morgan St.
Bluffton, IN 46714
Phone: [phone]
Fax: [phone]
MADE IN
USA !
Patent #5,975,719
®

Care and Operation of Your New
Fluorescent Utility Light
Read this manual before attempting to operate or service this unit.
CAUTION
1. Inspect cord regularly for damage and replace if necessary for user safety.
2. Do not submerge.
3. When hanging reel on ceiling (see bottom of opposite page):
• By hoo : Close hoo with pliers to prevent reel from falling down.
• By Brac et Pin: With reel in place, bend end of “L” shaped pin to prevent pin from
falling out.
• Read mounting instructions carefully before installing.
4. Use in covered areas out of rain and weather.
5. CAUTION, IMPORTANT SAFETY INSTRUCTIONS - This portable lamp has a polarized
plug (one blade is wider than the other) as a feature to reduce the ris of electric shoc .
This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the
outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Never use an
extension cord unless plug can be fully inserted. Do not alter the plug.
"ATTENTION,INSTRUCTIONS IMPORTANTES DE SECURITE
-CETTE LAMPE PORTATIVE A UNE FICHE POLARISANTE (UNE LAME EST PLUS
GRANDE QUE L'AUTRE) COMME CARACTERISTIQUE POUR REDUIRE LE RISQUE
DE CHOC ELECTRIQUE. CETTE FICHE N'ENGAGE Q'UNE PRISE POLARISANTE. SI
LA FICHE N'ENGAGE PAS COMPLETEMENT LA PRISE, ALORS RENVERSER LA, SI
ELLE N'ENGAGE TOUJOURS PAS, METTER VOUS EN RAPPORT AVEC UN
ELECTRICIEN QUALIFIE. NE JAMAIS UTILISER AVEC UN PROLONGATEUR SI LA
FICHE N'ENGAGE PAS COMPLETEMENT. NE CHANGER PAS LA FICHE."
OPE ATION AND MAINTENANCE
1. Plug the unit into a 120V AC outlet. The Lite® power supply cord is UL listed and meets
OSHA standards.
2. To start, depress and release switch in handle of wor light. The lamp will flic er as the
automatic starter lights the lamp. To turn off depress, and release again.
3. Disconnect the power suppl before servicing.
4. Keep the unit free from grease and dirt by using a damp cloth with mild detergent, or
waterless hand cleaner. This removes dirt from scratches in the outer tube and will
provide the best light output at all times. If the tube is damaged or badly scratched, it is
easily replaced and is available as a replacement part. (see the bac page for contact
information)
5. Do not use solvents such as gasoline to clean unit or cord as it ma es the parts brittle. Do
not allow bra e fluid to contact the outer tube as it will cause permanent damage.
6. Regular cleaning of cord will prolong cord life.
ELAMPING
UNPLUG LIGHT BEFORE RELAMPING! Unscrew outer tube from handle of light and
remove. Pull lamp from soc et and replace. Before screwing outer tube back into
handle, make sure lamp fits securel inside the outer tube lamp indentations.
Note: Continue to screw the outer tube into the handle until it “clic s” into place.

MOUNTING INST UCTIONS FO MODELS WITH EEL
Description Part No. Description Part No.
1. Lampholder 5000-045 9. Insulated Connector 5000-0400
. Lamp - 13 watt 5000- 041 10. Reflector 5000-0457
3. Outer Tube (includes 4 and 10) 5000-0114 11. Cordset - 0’ 5000-6065
4. Bail Hook 5000-0453 Cordset - 1 ’ 5000-6069
5. Handle Assembly 5000-0454 Cordset - 18” 5000-6066
6. Strain Relief 5000-0455 1 . * Reel Cordset - 0’ 5000-6067
7. Switch Assembly 5000-0030 * Reel Cordset - 50’ 5000-6068
8. Ballast - 13 watt 5166-3543
* cord and terminals only, not the reel
®

90 Day Warranty
General Manufacturing Inc. warrants to the purchaser of this new light that it was
thoroughly tested and inspected and found to be in perfect wor ing order before
leaving our factory. If within 90 days from the date of purchase, any part of this
wor light proves to be defective in material or wor manship, such defective part
will be repaired or replaced (company option) free of charge, at our factory. The
company's liability in all events is limited to the purchase price paid.
The warranty does not apply to the fluorescent lamp nor does it apply to damage,
alteration, misuse or abuse not attributed to General Manufacturing, Inc., its
representatives, dealers or their employees. This warranty does not apply if the
product is mishandled or operated at a voltage exceeding, that shown on the
reflector.
General Manufacturing, Inc. has made a diligent effort to illustrate and describe
the products in its literature accurately, however such illustrations and
descriptions are for the sole purpose of identification and do not express or imply
a warranty that the products will necessarily conform to the illustrations or
descriptions.
When returning product for warranty repair, please provide: a brief description of
your problem and your return address.
If this Worklight malfunctions or is in need of repair, send to:
General Manufacturing, Inc.
Customer Service Department
1100 South Morgan Street
Bluffton, IN 4 714
Phone: [phone]
Fax: [phone]
WEBSITE: www.saftlite.com
E-MAIL: [email protected]
Form No. 9032-7037 - Rev050803
B Y G E N E R A L M F G . IN C .
MADE IN USA!
®