General Titanium Series User manual

TRL-60RS
RED ROTARY LASER
INSTRUCTION MANUAL

2
SAFETY
Read the following safety instructions before
attempting to operate this product.
Keep these instructions in a safe place or store in the
carry case for future reference.
SAVE ALL WARNINGS AND INSTRUCTIONS FOR
FUTURE REFERENCE.
WARNING: Read and understand all
instructions.
• Use the laser only with the specifically designated
batteries.
• Store the laser out of reach of children and other
untrained persons. Lasers are dangerous in the
hands of untrained users.
• Use only accessories that are recommended for
your model.
• Tool service must be performed only by qualified
repair personnel. Repairs, service or maintenance
performed by unqualified personnel will void the
warranty. Only approved and authorised service
technicians can carry out warranty repairs.
• Do not use optical tools such as a telescope or
transit to view the laser beam. Serious eye injury
could result.
• Do not place the laser in a position which may
cause anyone to intentionally or unintentionally
stare into the laser beam. Serious eye injury could
result.
• Do not position the laser near a reflective surface
which may reflect the laser beam toward anyone’s
eyes. Serious eye injury could result.
• Do not use optical tools to view the laser beam.
• Do not set up the tool at a position where the laser
beam can cross any person at head height.
!

3
• Do not let children come in contact with the laser.
• Turn the laser off when it is not in use. Leaving
the laser on increases the risk of staring into the
laser beam.
• Do not operate the laser around children or allow
children to operate the laser. Serious eye injury
may result.
• Do not remove or deface warning labels.
• Position the laser securely on a level surface.
Damage to the laser or serious injury could result
if the laser falls.
WARNING: Do Not Disassemble
The Laser.
There are no user serviceable parts inside.
Disassembling the laser will void all warranties on
the product. Do not modify the product in any way.
Modifying the tool may result in hazardous laser
radiation exposure.
!
!
CAUTION: Class 2 Laser Product
• Never look into the laser beam directly and
intentionally.
• Do not use optical tools to view the laser beam.
• Do not set up the tool at a position where the
laser beam can cross any person at head height.
• Do not let children come in contact with the laser.
SAFETY (continued)

4
ITEM CHECKLIST
Please ensure the following items are included with your laser level.
If anything is missing please contact your retailer.
Laser glasses
Carry case Indoor charger
Rechargeable
battery pack
Alkaline
battery pack
Laser targetDetector & clampRemote controlGeneral Titanium
Series TRL-60RS
INCHES CM
1
1
2
3
4
5
6
7
2
3
SCAN
TILT
ALARM
AUTO
GRADE
SCAN
TILT
ALARM
AUTO
GRADE
MANUAL
GRADE
AUTO
GRADE
TILT
ALARM
MANUAL
GRADE
AUTO
GRADE
TILT
ALARM

5
LASER OVERVIEW: FRONT
Rotating laser port
Protective lighthouse
LCD display screen
Control panel
Rechargeable battery
charging port
Battery compartment
with rechargeable battery
SCAN
TILT
ALARM
AUTO
GRADE
SCAN
TILT
ALARM
AUTO
GRADE
MANUAL
GRADE
AUTO
GRADE
TILT
ALARM
MANUAL
GRADE
AUTO
GRADE
TILT
ALARM

6
LASER OVERVIEW: BASE
Carry handle
Battery compartment
with rechargeable battery
5/8” x 11 thread for
horizontal operation
on a tripod
Padded feet for vertical
operation on a flat surface

7
LASER OVERVIEW: BACK
Rotating laser port
Carry handle
5/8” x 11 thread for vertical
operation on a tripod
Padded feet for vertical
operation on a flat surface

8
MANUAL
GRADE
AUTO
GRADE
TIL T
ALARM
LASER OVERVIEW: CONTROL PANEL
Power
Dial-in grade mode
Tilt alarm
Manual / automatic mode
Scanning mode
Speed control
LCD display screen
Clockwise rotation
Counter clockwise rotation
Grade adjustment
Grade adjustment

9
Battery level
Automatic grade mode
Scan mode
Manual grade mode
Tilt alarm
Scan mode setting
(when scan mode is active)
RPM rotation speed
X-axis Grade percentage
Grade percentageY-axis
Self-levelling (flash)
LASER OVERVIEW: LCD SCREEN

10
REMOTE CONTROL OVERVIEW: FRONT
Tilt alarm
Counter clockwise rotation
Clockwise rotation
LCD display screen
Grade adjustment
Manual grade mode
Grade adjustment
Automatic grade mode
Speed controlScan mode

11
Battery compartment
REMOTE CONTROL OVERVIEW: BACK

12
REMOTE CONTROL OVERVIEW: LCD SCREEN
Battery level
Automatic grade mode
Scan mode Manual grade mode
Tilt alarm
Rotation speed (RPM)
X-axis
Y-axis
Self-levelling

13
DETECTOR OVERVIEW: FRONT
Speaker on / off Detection mode
LCD display screen
LED indicators
Laser sensor
Metric or imperial selection (press)
Screen backlight (hold)
Power on / off (detector)

14
DETECTOR OVERVIEW: LCD SCREEN
Brightness indicator
Arrow indicator
Arrow indicator
Battery indicator
Centre alignment
Detection mode
Speaker indicator
Measurement
Unit
Plus and minus indicator

15
Battery compartment
Speaker
Staff clamp mounting point
LCD display screen
DETECTOR OVERVIEW: BACK

16
POWER SUPPLY
Indoor charger / mains power adaptor
• The indoor charger is for indoor use only.
• Do not store in locations where moisture can be
present or where the chargers could be exposed
to extreme temperatures.
• If a charger becomes damaged, stop using
immediately and seek a replacement.
WARNING: Only use the supplied charger.
Using an incorrect charger will void the
warranty. Do not charge alkaline batteries.
USING YOUR LASER
!
Rechargeable battery pack
• The instrument is supplied with a rechargeable
Ni-MH battery pack that is located on the front
of the instrument below the control panel.
• The rechargeable battery pack is supplied only
partially charged. Charge the rechargeable
battery pack before use. Keep the rechargeable
battery pack in the carry case when not in the
laser level.
• The power indicator light will flash when the
battery is low. The instrument should be re-
charged as soon as possible.
• Battery pack capacity decreases at low
temperatures; a depleted pack may not function
when cold.

17
Removing and inserting the rechargeable battery
pack or alkaline battery pack
• Loosen the battery pack screw on the front of the
instrument below the control panel and slide the
battery pack out. If the screw is tight, loosen with
a screwdriver.
• Insert the battery pack and retighten the battery
pack screw. For better weather sealing, use a
screwdriver to tighten.
WARNING: Do not attempt to disassemble the
battery pack.
USING YOUR LASER (continued)
!
Charging the rechargeable battery pack
• Insert the charger into the charging port on the
rechargeable battery pack. Progress will be
shown by the power indicator display on the
charger as below:
Red (flashing) = Charger and battery
are not connected.
Red (constant) = Battery is charging
Green (constant) = Battery is charged
• Charging time is approximately 5 hours for a
depleted battery.
The battery pack does not need to be inserted
in the laser whilst charging via the port on the
battery pack.
i

18
USING YOUR LASER (continued)
HORIZONTAL MEASUREMENT SET UP
Level surface set up
• Select a place as close and practical to the work
site as possible, and ensure that the location is
clear of traffic.
• Place the laser level onto a reasonably level
surface with the lighthouse facing upwards.
Tripod set up
• Select a place as close and practical to the work
site as possible, and ensure that the location is
clear of traffic.
• Extend the tripod legs to the required height and
then spread the legs wide enough so that the
tripod platform is stable.
• Place the laser level onto the tripod with the
lighthouse facing upwards and thread the yoke
into the base until firm. Do not over tighten as this
may cause damage to the laser level or tripod.

19
USING YOUR LASER (continued)
VERTICAL MEASUREMENT SET UP
Level surface set up
• Select a place as close and practical to the work
site as possible, and ensure that the location is
clear of traffic.
• Place the laser level onto a reasonably level
surface with the control panel facing upwards.
Tripod set up
• Select a place as close and practical to the work
site as possible, and ensure that the location is
clear of traffic.
• Select a place as close and practical to the work
site as possible, and ensure that the location is
clear of traffic.
• Extend the tripod legs to the required height and
then spread the legs wide enough so that the
tripod platform is stable.
• Place the instrument onto the tripod with the
control panel facing upwards and thread the yoke
into the back until firm. Do not over tighten as this
may cause damage to the instrument or tripod.

20
OPERATION
Powering on
• Press the power button once and the instrument
will power on and begin automatically self-
levelling. When this levelling process is complete,
the penta prism inside the lighthouse will start
rotating.
• If the instrument is outside the self levelling range
the instrument will not level causing the laser beam
to flash continuously. If this occurs, reposition the
instrument onto a level surface until the instrument
can level off.
Powering off
• Press the power button once and the instrument
will power off.
USING YOUR LASER (continued)
Speed control
• Press the speed control button on the laser or
remote control to cycle through various rotational
speeds.
• The current rotation speed selected will be
displayed on the LCD screen and on the remote
control.