manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. Genesis
  6. •
  7. Cables And Connectors
  8. •
  9. Genesis Cables Servo/Bass User manual

Genesis Cables Servo/Bass User manual

Genesis Servo Bass Cable
Owner’s Manual
Rev.1.0
The Genesis Servo/Bass Cable
The concept of our servo-bass s stem is an eas one to understand. It emplo s an
accelerometer in the woofer to constantl monitor the movement of the cone and
instantaneousl compare it to the input signal. This comparison circuit identifies an
deviation from the input signal and applies a corrective signal to compensate; resulting in
the virtual elimination of the inherent distortion of the woofer.
In the Genesis products with an external amplifier, this means that the servo/bass cable
that connects the woofer and accelerometer to the servo amplifier is a critical part of the
servo s stem feedback circuit. The Genesis Servo/Bass cable is designed to work as a
s stem with the servo circuit and the amplifier. It is a speaker cable, and a feedback
circuit cable engineered together.
Grounded shielding is emplo ed to ensure minimal crosstalk interference between the
accelerometer return and the high-voltage speaker signal. Spaced and tightl constrained
conductors are used for the speaker signal to ensure that the inductance, capacitance, and
resistance of the cable are optimal for the servo s stem.
Instructions For Grounding the Shield
On Genesis Servo Cables
Step 1.- Remove the grounding screw from the amplifier chassis. This screw is located on
the rear left hand corner of the chassis bottom.
Figure 1
Step 2. – Using a small piece of 240 grit sandpaper sand the paint around the screw
hole until the chassis metal is exposed.
Figure 2 Figure 3
Step 3. – Using the screw removed in step 1, attach the ring terminal connector on the
Y-cable to the chassis.
Figure 4
Step 4. – Connect the male 1/8” mini jack connector on the ground lead of the left
channel cable pair to one of the female 1/8” mini jack connectors on the Y-
cable.
Figure 5
Step 5. – Connect the male 1/8” mini jack connector on the ground lead of the right
channel servo cable pair to the second female 1/8” mini jack connector on the
Y-cable.
Figure 6

Popular Cables And Connectors manuals by other brands

CYP CLUX-1H8CAT Operation manual

CYP

CYP CLUX-1H8CAT Operation manual

Rosslare MD-14U installation manual

Rosslare

Rosslare MD-14U installation manual

Philips CityTouch Connector Node LV LLC7260 installation instructions

Philips

Philips CityTouch Connector Node LV LLC7260 installation instructions

Miller XPS 450 CE user guide

Miller

Miller XPS 450 CE user guide

Philips SWV3212S/10 user manual

Philips

Philips SWV3212S/10 user manual

VOLTCRAFT 2181308 operating instructions

VOLTCRAFT

VOLTCRAFT 2181308 operating instructions

Philips SWV4434W/10 user manual

Philips

Philips SWV4434W/10 user manual

Sony CLIE PEGA-HS10 operating instructions

Sony

Sony CLIE PEGA-HS10 operating instructions

Prodigy SW-OV User instruction manual

Prodigy

Prodigy SW-OV User instruction manual

B+B SmartWorx 232MDS quick start guide

B+B SmartWorx

B+B SmartWorx 232MDS quick start guide

Festo CTEU-PB Electronics description

Festo

Festo CTEU-PB Electronics description

Audioplex IRB-4 installation manual

Audioplex

Audioplex IRB-4 installation manual

YOKOGAWA WU10 instruction manual

YOKOGAWA

YOKOGAWA WU10 instruction manual

THine THSER101 quick start guide

THine

THine THSER101 quick start guide

InCarTec 29-UC050-SAAB quick start guide

InCarTec

InCarTec 29-UC050-SAAB quick start guide

TRENDnet TWP-100R1K user guide

TRENDnet

TRENDnet TWP-100R1K user guide

JST XLR-02V manual

JST

JST XLR-02V manual

Actisense NMEA 0183 Information sheet

Actisense

Actisense NMEA 0183 Information sheet

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.