Genexis FiberTwist Series User manual

P3414B
FiberTwist Series
Installation Guide

Button overview Port overview
Power port
Telephone
portLAN ports
Unlock button
Remove FiberTwist or Blind Cover – press and
hold while twisting counterclockwise
Reset button (recessed)
Reset – press and release
LED dim button
Dim LEDs – press and release repeatedly to
dim LEDs

System
Green – system ok
Green (blinking) – booting
Red – system error
Red (blinking) – insuicient optical signal
O– power o
Uplink
Green – link ok
Green (blinking) – link ok, no remote management
O– no link
Phone
Green – voice service registered and ok
Green (blinking) – voice service unregistered
O– voice service disabled
LED overview

Box contents
• Genexis FiberTwist (active device)
• Power adapter
• Labels (self-adhesive)
Label position
The product label is positioned on the
back of the active device.
Preparation
Ensure there is a power socket
within reach of where the device
is being installed.
Important: Instructions need
to be followed precisely and
uninterrupted. This minimizes
the risk of damage (a severe
degradation of signal quality)
to the fiber optic connectors.
Various translations of this document (if available) and additional product
information can be foundon https://genexis.eu/product/fibertwist/downloads
Installation guide
Remove Blind Cover (if present)
1.Press and hold the unlock button (see button overview).
2. Rotate the Blind Cover counterclockwise till it blocks.
3. Remove the Blind Cover from the baseplate (FTU) by pulling
it towards yourself.
4. Store the Blind Cover in a safe place.

Remove dust cap
1.Take the FiberTwist out of the box.
2. The dust cap is connected to the red string located on the rear of the FiberTwist.
3. Remove the dust cap by pulling the red string.
4. Store the dust cap in a safe place.
Twist!
1.Place the FiberTwist on the FTU as shown in the picture below.
2. Rotate clockwise until it clicks into place.
3. Make sure the FiberTwist is aligned squarely on the FTU,
each edge must line up directly with the FTU below.
Your FiberTwist is now installed!

Company Name
Genexis Netherlands B.V.
Company Address
Lodewijkstraat 1a
5652 AC Eindhoven
The Netherlands
Name and title of authorized person
Maarten Egmond, CTO
Signature of authorized person
Place of issue Date of issue
Eindhoven 2021-11-29
The Netherlands
Hereby, Genexis Netherlands B.V. declares that the product FiberTwist P3414B is
in compliance with Directives 2014/30/EU, 2014/35/EU, 2011/65/EU, Delegated
Directive 2015/863 and Ecodesign Directive 2009/125/EC.
The full text of the EU declaration of conformity is available at the following
internet address: https://genexis.eu/product/fibertwist/red/fibertwist-p3414b
EU Declaration of Conformity
Connecting the FiberTwist
1.If required, connect your telephone to the phone port via an RJ11 network cable.
2. If required, connect your personal devices to the LAN ports via an RJ45
network cable.
3. Connect the supplied power adapter to the FiberTwist and plug the adapter
into a power socket.
Laser safety
This product contains a laser that emits invisible light. It is a Class 1Laser
product, which means it is safe under all conditions of normal use. However, it
is still advised to not look directly into the fiber connector when the product is
powered on.
If at some point in the future it becomes necessary to uninstall the FiberTwist,
please place the Blind Cover back on the FTU immediately and put the dust cap
back on the FiberTwist.

Revision 1.0- November 2021- Copyright © 2021 Genexis Netherlands B.V. All rights reserved.
Genexis assumes no responsibility for any inaccuracies in this document. Genexis reserves
the right to change, modify, transfer, or otherwise revise this publication without notice.