Genie WONVR14P5 User manual

Quick Start Guide
Please read these instructions carefully before operating the unit
and keep for further reference.
4 Channel H.265 Optimised
NVR with 1HDD Bay
WONVR14P5

ii
Intro Section
Please read this instruction carefully before operating the product and keep it for further
reference. All examples and pictures used here are for reference only.
The contents of this manual are subject to change without notice.
This device should be operated only from the type of power source indicated on the
marking label. The voltage of the power must be verified before use.
CAUTION:
• Please check the device and the accessories after getting the device. If there are any
damages, shortages or defects, please contact your dealer immediately.

Contents
iii
1.0 Introduction..........................................................................................................4
1.1 Product Features...........................................................................................4
1.2 Product Dimensions.....................................................................................4
1.3 Specification.................................................................................................5
2.0 HDD Installation...................................................................................................6
3.0 Rear Panel Instruction..........................................................................................7
4.0 Start Up and Shut Down......................................................................................8
5.0 Login and Disk Settings.......................................................................................9
5.1 Login .............................................................................................................9
5.2 Disk Settings ................................................................................................9
6.0 Configurations and Connections ........................................................................10
6.1 Network Configuration & Adding IP Camera...............................................10
7.0 Record Settings....................................................................................................11
8.0 NAT.......................................................................................................................12
9.0 Manual Recording and Playback .........................................................................13
9.1 Manual Recording.........................................................................................13
9.2 Playback.......................................................................................................13

4
The Genie ‘Optimised’ WONVR14P5 PoE Network video recorder offers 4 channel recording
of up to 5 Mega Pixels on every channel. The WONVR14P5 NVR supports 4 channel
simultaneous playback and has 4 PoE ports.
1.1 Product Features
• Supports 4 channel 5MP, 4MP, 3MP, 1080p, 960p and 720p IP input
• Adopt standard H.265 and H.264 high profile compression format to get high quality
video at much lower bit rate
• Intuitive and user friendly Graphic User Interface (GUI), Windows style operation by
mouse
• Multi-mode recording: Manual / Timer / Motion / Sensor
• Search : Time slice, time, event (Manual, sensor, motion), Tag search
• Express and flexible backup via USB, network etc.
• 4 channel simultaneous playback
• Pentaplex : Preview, Record, Playback, Backup and Remote Access
• DHCP, DDNS, PPPoE network protocol and CMS supported
• Remote control via IE or CMS : Preview, playback, backup, PTZ and configuration
• Dual stream technology for local storage with high definition, remote network
transmission and remote surveillance with mobile device
• Multi-user online simultaneously
• Authorisation management, log view and device status view
• 1080p HD output, true high resolution display
• Support PTZ preset and auto cruise, up to 255 presets and 8 cruises
• Support NAT function and QR code scanning by mobile phone and iPad
• Powerful smart phone & iPad surveillance with iOS and Android OS
1.2 Product Dimensions
1.0 Introduction
255mm
234mm
42mm

Quick Start Guide 4 Channel H.265 Optimised NVR with 1HDD Bay
5
1.3 Specification
Model WONVR14P5
System OS Embedded Linux
Video
Network Input 4 CH IPC input
Network Access Format 5MP / 4MP / 3MP / 1080p / 960p / 720p @ 25 / 30fps
Output HDMI x 1 : 1920×1080 / 1280×1024 / 1024×768
VGA x 1 : 1920×1080 / 1280×1024 / 1024×768
Compression Standard H.265, H.264
Audio Network Input 4 CH IPC audio input
Audio Local Output No (HDMI supports the audio output)
Record
Record Stream Dual stream recording
Resolution 5MP / 4MP / 3MP / 1080p / 960p / 720p @ 25 / 30fps
Mode Manual, Timer, Motion, Sensor
Mobile Device OS iOS, Android
Storage HDD SATA x 1, up to 6TB per HDD
Playback
Simultaneous Playback 4 CH max.
Search Time slice / Time / Event / Tag search
Smart Search Highlighted colour to display the camera record in a certain period of time, different
colours refer to different record events
Function Play, Pause, FF, FB, Digital zoom, etc
Network
Interface RJ45 100 Mbps x 1
Protocol TCP / IP, PPPoE, DHCP, DNS, DDNS, UPnP, NTP, SMTP
IP Input Access / Transfer
Bandwidth 32Mbps / 32Mbps
Alarm
Mode Manual, Sensor, Motion, Exception
Input No
Output No
Triggering Record, Snap, Preset, E-mail, etc.
Remote
Monitoring
Immix Compatible with Immix via RTSP only (2-way audio not supported)
Sentinel Yes, Firmware 1.1.0 or later
Backup Local Backup USB Stick, USB mobile HDD
Network Backup Yes
Port USB USB 2.0 × 2
Remote Controller Optional
Others
Power Supply DC12V, 1.5A
Consumption <6W (Without HDD)
Working Environment Temperature: -10°C – 50°C,
Humidity: 10% – 90%
Dimensions 255 × 234 × 42 mm

6
This series of the product supports 1 SATA hard drive. Please make sure that the device is
powered off before the installation. The pictures of the installation are for reference only.
1. Loosen the screws to open the cover.
2. Place the HDD onto the bottom of the machine.
3. Turn over the machine and secure the HDD with the screws.
4. Connect the power and data cables.
5. Install back the cover and secure it with the screws.
Note: Please check the inside structure of the device and make sure that the cables are
connected well before installing the cover back. Please format the HDD before using.
2.0 HDD Installation

7
The interfaces of the rear panel are for reference only.
Rear panel for WONVR14P5
Rear Panel for WONVR18P5
3.0 Rear Panel Instruction
Name Description
VGA Connector for VGA output
HDMI Connector for HDMI output
USB Connectors for USB devices
LAN RJ 45 Ethernet port
PoE Ports 4/8 PoE network ports; connect to PoE IP
cameras
DC48V Connector for power input
Power
Switch
Power
Connector

8
Startup
1. Connect the monitor and the power.
2. The device will boot and the power indicator will display blue.
3. A wizard window will pop up.
Shutdown
Click “Start” and then select “Shutdown” icon. This will bring up a shutdown window. The
device will shut down by clicking “OK” button. Then disconnect the power.
4.0 Start Up and Shut Down

9
5.1 Login
You must configure the wizard window if you start the NVR for the first time. Choose the
language and read the privacy statement. Then set the data, time and zone as needed.
After that, set the login password.
The default username is admin and the default password of admin is 123456. Set your own
password or use the default one when you use the wizard for the first time. Enable pattern
lock and click “Edit” to set the pattern lock. Then set security questions and answers.
It is important for you to remember these answers, or you will not be able to reset your
password. Click “Next” to continue.
5.2 Disk Settings
You can view the disk number, disk capacity of the NVR and serial number, Read/Write
status of the disk. Click “Format” to format the disk. Click “Next” to continue.
5.0 Login and Disk Settings

10
6.1 Network Configuration & Adding IP Camera
1. Enter IP address, subnet mask, gateway, etc. If using DHCP, please enable DHCP in both
the NVR and the router.
2. Enter HTTP port (the default value is 80) and server port (the default port is 6036).
3. The internal ethernet port is the port which connects all the PoE ports with the NVR
system. The PoE ports are available if the internal ethernet port is online, if it is offline,
all the PoE ports will be unavailable.
4. Add Camera. Click “Next” to go to the following interface.
Click “Refresh” to refresh the list of online
IP cameras which are in the same local
network with the NVR. Click + to add the
searched camera. Click “Add All” to add all
the cameras in the list. Click to delete the
added camera. Click “Delete All” to delete all
the added cameras.
5. Click to edit an IP camera as shown on the above left. Enter the new IP address,
subnet mask, gateway, username and password of the camera. Click “OK” to save the
settings. Click to edit the added camera as shown on the above right. Enter the
new camera name, IP address, port, username and the password of the camera. You
can click “Test” to test the effectiveness of the input information. Click “OK” to save the
settings. You can change the IP camera name only when the added camera is online.
Click “Next” to continue.
6.0 Configurations and Connections

11
There are two record modes: auto and manual.
Auto Mode: Select one auto mode in the interface as shown below and then
click “Next” to save the settings. Click “Advanced” to self-define a record
mode.
Manual Mode: Set the “Sensor Record”, “Motion Record”, “Analytics Record” and “Schedule
Record” of each camera. Please enable the record as needed. Click “Next” to continue.
7.0 Record Settings

12
You can enable the NAT function in the interface or set it in the network configuration after
exiting the wizard. You can scan the QR code through the mobile surveillance APP available
for iOS or Android to easily view your cameras.
Web Browser Access Through NAT Function
G to Start → Settings → Network → NAT tab. Enable NAT and select the NAT Server Address.
Click “Apply” to save the parameters.
Enter www.autonat.com in the address bar of your browser and then press enter to go to
the following interface. If you are the first time to access the NAT, you shall download and
install the plug-in according to the popup tips. After that, re-open your web browser and
enter the above-mentioned address. Then the login box will appear. Enter the device serial
number, username and password.
Device Serial Number:
Click on the menu bar at the bottom of the live interface to check the serial number or
go to Start → Settings → Network → Network Status to check the serial number of the NVR).
Username:
The username of the NVR. The default username is admin.
Password:
The password of the NVR. The password is set by yourself when you configure the wizard
for the first time.
8.0 NAT

13
9.1 Manual Recording
Before recording, please install and format a HDD. In the live interface you can see the
menu toolbar. Click button to start recording. Click it again to stop recording. You can
also click to check the status of the recording.
9.2 Playback
Instant Playback
Click “Instant Playback” in the right-click menu of the camera’s preview window to
select or drag the playback progress bar to change the playback time to play back
the record.
General Playback
Click on the tool bar at the bottom of the live preview interface or click
Start → Playback to go to the playback interface as shown below. You can also
add the playback cameras manually. Click in the playback window to pop up the
“Add Camera” window. Check the cameras in the window and then click “Add” to
add playback camera. The record files of the added playback camera
will be played in the playback interface.
9.0 Manual Recording and Playback

Sales [phone]
Enquiries [email protected]o.uk
Website www.genieproducts.co.uk