Genie HDUBARTK-R User manual
Quick Start Guide
Please read these instructions carefully before operating the unit
and keep for further reference. All the examples and pictures used
here are for reference only. The contents of this manual are subject
to change without notice.
AHD, CVI, TVI and CVBS Active
Video Balun - Receiver
HDUBARTK-R
Quick Start Guide AHD, CVI, TVI and CVBS Active Video Balun - Receiver
2
The Genie HDUBARTK-R is a 1CH HD analogue video UTP receiver that transfers
real-time analogue video signal up to 1,200m (CVBS) through Cat5/5e/6 cable.
Features
• Up to 1,200m transmission distance (with active transmitter) (CVBS)
• Compatible with HDCVI, HDTVI, AHD, CVBS signals
• ESD protection
Specifications
Dimensions
Function Transfer Signal Number 1CH Video
Transmission Distance Up to 1,200m (CVBS)
Video
Transmission
and Connector
Video Connector 1 x BNC (Male)
Cable Port 1 × 3 Pin Terminal
Compatible Video Type AHD, CVBS, HDCVI, HDTVI Signal
Transfer Bandwidth 0–75MHz
Signal Indicator Yellow solid ON : Power input normal
Green solid ON : Signal input normal
Anti-Interference >60dB
Protection
Surge Protection of
Coaxial Port
2 KV Differential-mode
2KV Common-mode
Per :IEC61000–4–5
Surge Protection of Line
Connector
Signal Line-pair :
2 KV Differential-mode
2KV Common-mode
Per :IEC61000–4–5
ESD Protection
1a Contact Discharge 6 KV
1b Air Discharge 8KV
Per :IEC61000–4–2
Others
Voltage Input DC12–20V or A C9–24V
Working Temperature -10°C ~ 55°C
Storage Temperature -45°C ~ 75°C
Humidity 0 ~ 95%
Dimensions 113 × 45.5 × 29 mm
Weight 65g
113mm
45.5mm
Quick Start Guide AHD, CVI, TVI and CVBS Active Video Balun - Receiver
3
Panel Diagram
Installation Steps
Please check the following items before installation.
If anything is missing, please contact dealer.
• 1x HDUBARTK-R
• 1x User Manual
Please follow the steps as below:
1. Turn off the power of all the related devices before the installation; otherwise
the device would be damaged.
2. Check if the any cable has been occupied by other device.
3. Connect corresponding ports of cameras and other related devices with Video
BNC port of TX unit.
4. Connect the grounding terminal of TX unit by bare grounding wire and a pair
Ethernet cable.
5. Connect the grounding terminal of RX unit by bare grounding wire and a pair
Ethernet cable.
6. Connect display device and BNC port of RX unit by coaxial cable.
7. Connect power ports of RX and TX units by power cable.
8. Check the installation and connection of equipments are correct and the
equipments are working properly, then power on system.
9. Make sure image displays and other devices are working.
Troubleshoot
Please find the following solution when the device doesn’t work:
• Reboot
• Adjust the switch when DVR works smoothly.
• There are 2 marks of 10X on unit. Right mark features high definition and
saturation.
Quick Start Guide AHD, CVI, TVI and CVBS Active Video Balun - Receiver
4
Application
Note:
Standard Cat5e/6 cable and 75 4 or above coax are strongly suggested for
reaching the maximum transmission distance!
Please use standard UTP cable and coax to ensure the stable transmission.
Recommended Distance
1
0
A
2
5
0
V
L
N
CCC
Monitor
DVR
AC In
HDUBARTK-R
UTP Transmitter
HD Camera
UTP Cat5e/6
Signal T
ype HDCVI
720P
HDCV I
1080P
AHD
720P/960P
AHD
1080P
HDTVI
720P
HDTVI
1080P
Transmission
Distance 600m 500m 700m 300m 400m 400m
Table of contents
Other Genie Receiver manuals
