Gentech Four E's Scientific MI0101002 User manual

Safety Instructions
For your protection
• Read the operating instructions in full before starting up
and follow the safety instructions.
• Keep the operating instructions in a place where they can be
accessed by everyone.
• Ensure that only trained sta ffwork with the appliance.
• Follow the safety instructions, guidelines, occupational health
and safety and accident prevention regulations.
• Socket must be earthed (protective ground contact).
• Wear your personal protective equipment in accordance with
the hazard category of the media to be processed.
Otherwise there is a risk from:
- Splashing liquids
- Projectile parts
- Body parts ,hair ,clothing and jewellery getting caught.
• Keep hand/arm vibration to a minimum (Directive 2002/44/EC)
When operated manually:
- Keep the sample container as vertical as possible.
- Only exert the minimum pressure necessary for the mixing process.
- Use attachments for multiple samples when there is a large
number of samples.
• Set up the appliance in a spacious area on an even, stable,
clean, non-slip, dry and fireproof surface.
• The feet of the appliance must be clean and undamaged.
• Position the knob at the left stop before starting up.
Gradually Increase the speed.
• If the shaking movement of the appliance increases
(resonance), reduce the speed or pass through the critical
phase as quickly as possible.
MI vortex mixer
con pantalla digital LED

• Reduce the speed if
- The medium splashes out of the vessel because the speed
is too high
- The appliance is not running smoothly
- The container moves on the base plate
• Firmly secure the accessories and vessels in place, otherwise
shaking vessels could be damaged or projected out.
• Check the appliance and accessories beforehand for damage
each time you use them. Do not use damaged components.
• Position one single shaking vessel in the centre and several
shaking vessels so that they are evenly spread out.
• The appliance is not suitable for manual operation.
• Sharp edged vessels cause wear debris on the attachments.
• Beware of hazards due to:
- flammable materials
- glass breakage as a result of mechanical shaking power.
• Only process media that will not react dangerously to the
extra energy produced through processing. This also applies
to any extra energy produced in other ways, e.g. through light
irradiation.
• Do not operate the appliance in explosive atmospheres, with
hazardous substances or under water.
• Safe operation is only guaranteed with the accessories
described in the “Accessories” chapter.
• Always disconnect the plug before fitting accessories.
• The appliance starts up again automatically following a cut in
the power supply.
• The appliance may heat up when in use.
To the protection of the equipment
• The voltage stated on the nameplate must correspond to the
mains voltage.
• Protect the appliance and accessories from bumps and impacts.
• The appliance may only be opened by experts.
MI vortex mixer
con pantalla digital LED

Operator’s Control
Item Description
Speed Display
Time Display
Mode Indicator
Light
Mode Switch
Adapter
Function
Display the set speed
Display the set time in the continuous working
model. The continuous mode includes timed
running and untimed running. When timed
running, it shows the balance time “xx: xx”, when
the time is 0, the machine stops running. When
untimed running, it shows “Cont” and the
machine keeps running.
The left one is for continuous working mode and
the right one is for touch working mode.
It’s the continuous mode when the switch is on
the left side and the left mode LED is light. It’s
the touch mode when the switch is on the right
side and the right mode LED is light.
Different adapters are used for various mixing
applications
1
2
3
4
5
①
③
④
⑥
⑤
②
⑦
MI vortex mixer
con pantalla digital LED

Changing attachment Cross recessed
countersunk
head screw M4x8
Using insert
Item Description
Time/Speed
Setting
Function
Press the knob, the speed display will flash and
then set the speed in the range of 400-300rpm
by horizontal rotation of the knob. Press the knob
twice, the time display will flash, and then set the
time in the range of 0-99H59Min by horizontal
rotation of the knob. Press the knob again, the
time display will show “Cont” for continuous
untimed running. The mixer can keep the set
temperature and time in records. It shows the
values last time when powered on.
6
MI vortex mixer
con pantalla digital LED

Unpacking
• Unpacking
- Please unpack the device carefully
- In the case of any damage a fact report must be set
immediately (post, rail or forwarder)
• Delivery scope
- Vortex Mixer
- Plug-in power supply
- Operating instructions
Correct Use
• Use
- For mixing liquids
- Touch mode for single test tubes
- Continuous mode for single or several vessels
• Range of use
Laboratories / Schools / Pharmacies
• This device is suitable for use in all areas except:
- Residential areas
- Areas that are connected directly to low-voltage supply
network that also supplies residential areas.
The safety of the user cannot be guaranteed if the appliance is
operated with accessories that are not supplied or
recommended by the manufacturer or if the appliance is
operated improperly contrary to the manufacturer’s specifications.
Installation
• Assemble the adapters per the Figure 2 and 3.
• Choose the working mode by the mode switch
• Set the speed and time by the knob. There’s no need for time
setting in the touch mode.
MI vortex mixer
con pantalla digital LED

Use to remove
Dyes
Constructions materials
Cosmetics
Foodstuffs
Fuels
isopropyl alcohol
water containing tenside /
isopropyl alcohol
water containing tenside /
isopropyl alcohol
water containing tenside
water containing tenside
Do not allow moisture to get into the appliance when cleaning.
• Wear protective gloves during cleaning the devices
• Before using another than recommended method for cleaning
or decontamination, the user must ascertain with us that this
method does not destroy the instrument.
• The rubber of the attachments’ pads is a natural product, so
talcum can discharge .Clean the rubber pad with glycerin.
Spare parts order
When ordering spare parts, please give:
- Machine type - Manufacturing number, see type plate
Repair
In case that the device has to be cleaned, please be free from
any material which may constitute a health hazard.
If you require services, please return the appliance in its original
packing.
- Run the mixer by “Run/Stop” in the continuous mode.
- Turn o ffthe mixer by putting the mode switch on middle gear.
Maintenance
The appliance is maintenance-free.
Cleaning
Only use cleansing agents which have been recommended by us.
MI vortex mixer
con pantalla digital LED

Item
1
2
3
4
5
6
Part No.
MI0101002-31
7
MI0101002-32
MI0101002-33
MI0101002-34
MI0101002-35
MI0101002-36
Product Photo Description
MI0101002-14
Test Tube Attachment,
54 x Φ6mm, used with
MI0101002-14
Test Tube Attachment,
18 x Φ10mm,
used with MI0101002-14
Test Tube Attachment,
12 x Φ12mm,used with
MI0101002-14
Test Tube Attachment,
8 x Φ16mm,used with
MI0101002-14
Test Tube Attachment,
8 x Φ20mm, used with
MI0101002-14
Microtiter plate
attachment, used with
MI0101002-14
Universal top plate
Accessories
MI vortex mixer
con pantalla digital LED

Application of Accessories
MI0101002-13
MI0101002-31+
MI0101002-14
MI0101002-32+
MI0101002-14
MI0101002-33+
MI0101002-14
MI0101002-34+
MI0101002-14
MI0101002-35+
MI0101002-14
MI0101002-36+
MI0101002-14+
YY
Y
Y
Y
Y
Y
High Speed
Y
Adjustable Speed Model 400-3000rpm
Touch Mode Continuous Mode
Low Speed
YY
Y
Y
Y
Y
Y
High Speed Low Speed
Y
Accessory
The high speed is 3000rpm; the low speed is below 500rpm.
Item
8
Part No.
MI0101002-13
9
Product Photo Description
Standard top
MI0101002-37
＜Φ30mm tubes and
small vessels
Erlenmeyer flask
attachment 100-250ml,
used with MI0101002-14
MI vortex mixer
con pantalla digital LED

Technical Data
Warranty
In accordance with our warranty conditions, the warranty period
is 24 months. For claims under the warranty please contact your
local dealer. You may also send the machine directly to our
factory, enclosing the delivery invoice and giving reasons for the
claim. You will be liable for freight costs.
The warranty does not cover worn out parts, nor does it apply to
faults resulting from improper use, insufficient care or
maintenance not carried out in accordance with the instructions
in this operating manual.
Model
Operation mode
Type of movement
Orbital diameter
Speed range
Permissible ambient temperature
Permissible relative humidity
Protection class
according to DIN EN 60529
Voltage
Frequency
Power
Motor rating input
Motor rating output
Dimensions (W x H x D)
Weight
MI0101002
Continuous/touch operation
Orbital
6mm
0-3000rpm
5 - 40 °C
<80%
IP 21
200 - 240 / 115 / 100V
compatible
50/60 Hz
36W
30W
15W
107x146x166mm
2.62kg
MI vortex mixer
con pantalla digital LED