manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. GenTent
  6. •
  7. Tent
  8. •
  9. GenTent StormBracer 20k User manual

GenTent StormBracer 20k User manual

Copyright 2016, GenTent® Safety Canopies, LLC. All rights reserved. Nottingham, NH, USA. www.gentent.com V4
Email: [email protected]
Telephone: 781-33G-TENT (781-334-8368)
WHAT YOU WILL NEED
- 1/2” socket or open end wrenches
- 5/16” socket or open end wrenches
- (optional) 5/32” drill bit and 5/16” nut driver
or screwdriver)
- This guide
Optional:
Either: 5/16” x 2” Clevis Pins with Retainer or
Quick Detach Pins
Or: GenTent folding handle kit
www.gentent.com/products/mpaccflhdl
IMPORTANT PRODUCT SAFETY
WARNING
Always shut generator off before any fueling or maintenance procedures.
WARNING
Never position the refueling door on the same side of the generator as the exhaust muffler.
Spilled gasoline can result in fire.
WARNING
Never block or cover the generator exhaust muffler in any way. GenTent canopy must be
installed above generator exhaust muffler. Install GenTent electrical skirts such that they
cannot block exhaust in any way.
CAUTION
Do not over tighten clamps when installing on the frame as failure can occur. Always use the
included washers. This will assure a firm, stable connection that will stay level when the
fiberglass frame is in place.
CAUTION
Always grasp fiberglass rods firmly during installation to avoid the whipping motion that can
occur when a bent fiberglass rod is mistakenly released.
CAUTION
Avoid using GenTent in hurricane force winds (above 60mph).
NOTE
Should generator handles cause significant stretching of the elastic straps when extended, it is
advisable to release the elastics straps on the handle side of the generator before extending
generator handles.
NOTE
Should GenTent cover block pull starter, it is advisable to release the elastic straps on the pull starter
side and temporarily move GenTent canopy out of the way.
NOTE
When using GenTent during snow storms, it is recommended to periodically brush away any
accumulation that blocks the top vent.
THANK YOU
Your new GenTent® 20k makes a very nice fit
on your Generac GP 12000, GP 15000 or
GP17500 generator. The recommended
installation is to install two GTU adapters at
the electrical panel and then either replace
the handle bolts with quick detach pins or
reposition the handles. This is a step-by-step
guide for this process.
GenTent®20K Generac 15k/17.5k Addendum
INSTALLATION OVERVIEW
The process should take about 15 minutes:
Install GTUs: Remove electrical panel top bolts
only and reinstall with GTU flush to the panel
Choose a handles strategy:
- Make the handles quick detach, OR
- Install folding handles
Copyright 2016, GenTent® Safety Canopies, LLC. All rights reserved. Nottingham, NH, USA. www.gentent.com V4
INSTALL GTUs
- Remove one of the top bolts which secures the electrical panel to the frame using the 5/16” socket and/or
open end wrenches (Fig D.)
- Position one GTU flush over the electrical panel, align the hole and re-install the bolt through the GTU, the
electrical panel and the frame (Fig E.)
- Note that the two GTU’s included will have holes that are opposite each other (a Left and a Right), or will
have all four holes open
- Optionally, drill a 5/32” hole through the frame where the bottom hole aligns with the frame and install the
included #12x3/4” sheet screw
- Fig. F shows a GenTent clamp subsequently installed onto the GTU.
Fig. D Fig. E
Fig. F
Copyright 2016, GenTent® Safety Canopies, LLC. All rights reserved. Nottingham, NH, USA. www.gentent.com V4
OPTION 1: CONVERT HANDLES TO QUICK DETACH
This option allows the handles to be quickly detached/attached. If you choose this option, the GenTent can stay
installed, simply release the elastic straps on either side of the electrical panel to temporarily lift the canopy when using
the handles.
The pics below show two different types of quick detach pins, a Clevis pin on the left with a hitch pin clip, and a quick
detach ring pin on the right. Most hardware stores carry at least one type of quick detach pin. You will need four (4) of
these in the 5/16” x 2” size.
The handle is permanently connected to the frame with 4 carriage bolts. Replace these bolts with either of the quick
detach pin types above by unscrewing the existing bolt and simply sliding the quick detach pin into place (then locking it
with the clip pin as appropriate).
The GenTent should be initially installed with the handles off the generator. To move the generator, remove the elastic
from the left and right of the electrical panel and lift the canopy up. Install the handle with the quick detach pins, and
move the generator. When it becomes time to use the generator, move it into place outdoors, remove the handles and
put the elastics back in place under the GenTent clamps to the left and right of the electrical panel.
Copyright 2016, GenTent® Safety Canopies, LLC. All rights reserved. Nottingham, NH, USA. www.gentent.com V4
OPTION 2: REPLACE HANDLES WITH FOLDING HANDLES
We have an optional folding handle kit that is a bolt in replacement to the fixed handles provided with your generator.
These handles can be ordered with the GenTent 20k or ordered separately at www.gentent.com/products/mpaccflhdl.
This kit includes longer folding handles and installation hardware.
To install these handles, remove the fixed handles from the generator. There are four bolts that hold the handle in
place. Install the folding handles in the handle frame holes at the top and tighten. The universal handles accommodate
frame diameters from 1” to 1.5”. The Generac frame is 1” diameter in this area. Be sure to tighten the handles until the
handle flanges press against the frame.

Other GenTent Tent manuals

GenTent XKi User guide

GenTent

GenTent XKi User guide

GenTent Ridgid RD User guide

GenTent

GenTent Ridgid RD User guide

GenTent WeatherProof Setup guide

GenTent

GenTent WeatherProof Setup guide

GenTent StormBracer User guide

GenTent

GenTent StormBracer User guide

GenTent StormBracer 10k User guide

GenTent

GenTent StormBracer 10k User guide

Popular Tent manuals by other brands

Palram Arcadia 5000 Assembly instructions

Palram

Palram Arcadia 5000 Assembly instructions

Coleman TOUGH DOME /3025+ Handling and Assembly Instruction Manual

Coleman

Coleman TOUGH DOME /3025+ Handling and Assembly Instruction Manual

Backyard Discovery TRENTON 2105126 owner's manual

Backyard Discovery

Backyard Discovery TRENTON 2105126 owner's manual

Costco 781893 instruction manual

Costco

Costco 781893 instruction manual

Chinook Whirlwind Guide 5 Assembly instructions

Chinook

Chinook Whirlwind Guide 5 Assembly instructions

Storage Canopy EWC2020R Assembly instructions

Storage Canopy

Storage Canopy EWC2020R Assembly instructions

Jack Wolfskin BASE CAMP DOME manual

Jack Wolfskin

Jack Wolfskin BASE CAMP DOME manual

Magellan Miracle VK-1065 quick start guide

Magellan

Magellan Miracle VK-1065 quick start guide

Montgomery Ward 98350 Assembly instructions

Montgomery Ward

Montgomery Ward 98350 Assembly instructions

Kodiak 1680 owner's manual

Kodiak

Kodiak 1680 owner's manual

earth worth 1852 Assembly instructions

earth worth

earth worth 1852 Assembly instructions

Sierra Designs CONVERT 2 Pitching instructions

Sierra Designs

Sierra Designs CONVERT 2 Pitching instructions

TMG TMG-GH1220 product manual

TMG

TMG TMG-GH1220 product manual

Coleman STITCHLINE 2000007831 Setup instructions

Coleman

Coleman STITCHLINE 2000007831 Setup instructions

Big Agnes COPPER SPUR HV UL mtnGLO Setup instructions

Big Agnes

Big Agnes COPPER SPUR HV UL mtnGLO Setup instructions

Ironman4x4 IRTI0023 owner's manual

Ironman4x4

Ironman4x4 IRTI0023 owner's manual

Palram Vitoria 5000 instructions

Palram

Palram Vitoria 5000 instructions

Coleman X-CURSION TEPEE/210 Handling and Assembly Guide

Coleman

Coleman X-CURSION TEPEE/210 Handling and Assembly Guide

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.