Genuwine Cellars ELITE KIT RACK User manual

750ml 3 COLUMN RACK 750ml 6 COLUMN RACK 750ml 9 COLUMN RACK
1 - Left
Ladder 2130
(QTY: 1)
2 - Middle
Ladders 2130
(QTY: 2)
3 - Right
Ladder 2130
(QTY: 1)
4b - Back Spacer Bars 353
(QTY: 5)
4a - Front Spacer Bars 353
(QTY: 5)
6 - Crown Mould
(QTY: 1) 7 - Base Mould
(QTY: 1)
5 - Tilt Stop
(QTY: 1)
#6 Robertson Screws
(Square Head)
(QTY: 3)
#8 Robertson Screws
(Square Head)
(QTY: 3)
Angled Brackets
(QTY: 3)
We Recommend A
21 Gauge Nail Gun
(Use 21 gauge brand nails,
with appropiate air compressor
or electric nailer set to 80psi,
to prevent spliting)
Robertson
Screwdrivers #6 & #8
(Square Head)
Drywall Anchors
(QTY: 3)
375ml SINGLE COLUMN RACK 1.5L SINGLE COLUMN RACK 750ml SINGLE COLUMN RACK
ELITE KIT RACK ASSEMBLY INSTRUCTION
COMPONENTS HARDWARE TOOLS REQUIRED
Thank you for purchasing Elite Kit Rack by Genuwine Cellars. The following
instructions will help you assemble the 750ml COLUMN RACK. The same
procedure can be applied to the following kits shown.
Please study the i structio s carefully prior to starti g the assembly.
The following tools are required (NOT INCLUDED):
The following hardware is included in all kits:
(QUANTITY WILL VARY, DEPENDING ON KIT.)
The following components are included in the 750ml COLUMN RACK.
(COMPONENTS WILL VARY IN QUANTITY AND SIZE, DEPENDING ON KIT.) IMPORTANT!
Always follow the manufacturer's
instructions on how to use the nail
gun, to prevent injury. Genuwine
Cellars is not liable for any injury
incurred while assembling the kit.
Front
Back

A
B
A
B
STEP
1
STEP
2
STEP
3
STEP
4
Starting from the back of the racks. Place the ladders on flat, soft surface, so not to damage
front of racks. Space the ladders accordingly. (Note: E sure proper placeme t of ladders,
a d bottoms are all i same directio . Left a d right ladders, are placed o the e ds.
Bottle tilt should be i same directio .)
Front of Ladders
Back of Ladders
(Note: Bigger otch is
bottom of ladders)
From the bottom and working your way up, place the back spacer bars (4b) according to the
ladder notches. Make sure to carefully interlock the spacer bars to the ladders.
Once spacer bars are properly placed. Start
from the bottom of the rack, firmly apply
pressure to lock in the joint. Then apply two
nails with a nail-gun, to each joint. Remember
to firmly lock in each joint.
Firm Pressure
Firm Pressure
Apply Nails
While backs are still facing up, screw the angled brackets
to the back spacer bars as shown. Top, middle, and bottom.
Bracket
Bracket
Bracket
(Note: Bottom brackets
should be mou ted o
top of the spacer bar,
i stead of u der eath)
1
2
4b

C
D
C
D
STEP
5
STEP
6
STEP
7
With the help of another person, turn the rack so the back is on the floor, and the front is facing
up. Starting from bottom up, place the front spacer bars (4a) according to the ladder notches.
Make sure to carefully interlock the spacer bars to the ladders.
Front of Ladders
Back of Ladders
(Note: Bigger otch is
bottom of ladders)
Apply Nails
From the front and bottom of the rack, firmly apply
pressure to lock in the joint. Then apply two
nails with a nail-gun, to each joint. Remember
to firmly lock in each joint.
Flush
Applying the tilt stop, flush the tilt stop (5) to the bottom of the front,
middle spacer bar. Also, make sure to flush the tilt stop to the edge
of the right or left ladder. Hold firm and nail twice on each ladder.
Firm Pressure
Firm Pressure
STEP
8Optional, finish the 750ml column by applying the
base and crown mould.
4a
5
6
7
Tilt Stop
Spacer Bar
Flush