Genway C-5 SYSTEM G9 Villa Door Station Series User manual

ß enway
C-5 SYSTEM
G9 Villa Door Station Series
USER MANUAL
Please read this user manual carefully before using the products. Please keep
it for future reference.
(VER:V1 .10)

-
r:;- ----------------------- --- ~-:!
\ 11
..
INSTALLATION TIPS-
• The signal wires should be as far away as possible
from the interfering sourees.
• The signal wires should run on the low electronic
route and cannot go with the high electronic (e.g .
220V house power) route or transmission signal
route (e.g . CATV) in parallel.
• 00 not install the products in following situations.
• Humidity or rain
• Sun shine
• Shake or strike
• Dust
• High temperature
• Noise
This symbol warns people there is dangerous voltage
dose to the products. Be careful of shock .
This symbol warns people the note is very important. They
have to follow strictly in order for the system performs perfectly.
i. ~ ::J

Preface
Thankyouvery much for using Genway products that weredevelopedwith
the latesttechnology. Tomeet thedemands
ofu sers, Customer Satisfaction
is ourgoal.
Pleaseread thismanualcarefullybeforeusingthe products in order for the
productscanp
erform perfectly. In an effortto serveyoubetter, we we 1co me
any comments or suggestionsyou have.
Contents
1. Product lntroduction-: 1
2. Product Features···················································1
3. Specifications-: ···1
4. Appearance & Ports-»
···2
5. Diaqrarns-: ···3
Diagram for 1 door station & 1 indoor phone-r ••••••••••••••.••• "'3
Diagram for 1 door station & up to 4 indoor phones-: ••••••.•• "'4
Diagram for 2 door station & up to 3 indoor phones-: ••••••. ,••••5
Diagram for e-Iocks-:
•..•••••••••...•••..••••••.•••••••••••••••.•• "'6
6. lnstallatlon-: ···7
Door station-: 7
Power supply(4055)'" 8
Power supply(4001)&Distributor(41108/4230)'" 8
Changing name taq-» 9
7. Camera Adjustment·············································10
8. Operation- ···11
9. Appendix: Prepare
CAT.5 cable-: ···13
Product list··· ···15

1.Product Introduction
o
This door station is apart of C-5 one cable system. It is for villa/single family house
use. Simple one CAT.5common wiring, making communication
c1ear and trouble free.
One door station can be connected up to 4 indoor phones for a villa. Expandable to 2
door stations up to 3 indoor phones.And also available to connect with guard unit and
perimeter gate station. When there are many villas, they can be wired together in
network.
2.Product Features
• Vandal resistant panel, stainless steel construction, waterproof, flush mounting.
• Compatible with all audio and video indoor phones in C-5 system.
• Ooors can be released by various methods such as indoor phone, 10card,
SERVICE button, and EXIT button.
• Use1/3' CMOS color camera which isadjustable.The IR illumination ofters clear
image even in the dark.
• A sound system is programmed for friendly intercommunication.
• The enclosed remote control provides easy programme.
3.Specifications
Model Operating
voltage
Quiescent
current
(OC 35V)
Operating
current
(OC 35V) Temperature Camera
5403 OC35V
<:; 50mA
<:; 110mA -40° C-+70 °C
--------
54030 OC 35V
<:; 50mA <:; 130mA -40°C -+70 °C
--------
5809
5809-C
OC35V
<:; 50mA <:; 160mA -40°
C-+70 °C CCO&CMOS
PAL
View angle:90°
Adjustable angle: ±10°
58090
58090-C
OC 35V
<:; 50mA <:; 180mA -40°C -+70 °C
> <

-
4.Appearance & Ports
• Face Brand
[CALL) button
[OOOR OPEN) LEO
[SPEAK NOW) LEO
MIC
®
@onway
0000 00000 0000
00 0 00 0 0 0000 0 0
000 00000 00 0 0
00 00 0000 0 00 00
000000 00 0 00 0 0
...
®
®
S eaker
Infrared LEO
&Camera
IR Oetector
Card reader
&Name tag
[SERVICE) button
SPEAK OOOR
NOW OPEN
®
• Back
P
.,
IIL
"
cl
e
SL
'"
~
"
e
cl
I
e
c
Ir-
0
-8
..........
-8
cm
-
e
e
e
e
"
CALL SERVICE
o Port to indoor phone/distributor
1 2 3 4 15 6 78
01 1 01 VF· VF+IAF- AF+ GNO OC+
DD DD ID DD D
8 JP1 connector & software update port
J P1 rr== = = = = = = = = =r:::;-
~ f 0 '0 0 0 ' 0 '0 0 ~ 0 ' 11
8 Port to electronic lock (options)
[INOOOR)&[GNO): to EXIT button
GS INDOOR GNO
+12"
NO NC COM out
DDD DD DD

5.Diagrams
5.1 Diagram for 1 door station & 1 indoor phone
1. When there are only one door station and
one indoor phone, the connector of JP1
has to create a short circuit across the two
pins.
2.Max. Distance: <100m [In case longer,
please use an extra power supply on the
indoor phone.]
CAT.5
Port in door station
+
CX) 0 Brown
0
0
I"'- Z Brown/white
<.9
+ Blue
co
u,
«
I 0
L()
U.
Blue/white
«
+ o I Green
.q-
u,
>
I I
(")
u,
Rt-- Geee" lwh ite
>
l-
N 0
~I Oea",e
T""
I-
T""
0 0 1
Orange/white
Power supply
Indoor phone
Portin Ooor station
00 0 00 0 000

5.Diagrams
5.2 Diagram for 1 door station & up to 4 indoor phones
1.PORT1 ~ P O R T 4 in the distributor are for 4
indoor phones (audio or video).
2.Terminals in the distributor are useless here.
\, 3.Max. Distance: <100m [In case longer,
please use an extra power supply on each
indoor phone.]
0
DCt CAT.5
0
GND
0
AFt
0
AF-
0
VFt
0
0
0
VF-
LB
LA
I ndoor phone 4
Oistributor (411 OS)
Indoor phone 1
CAT.5
Ooor station
Orange/white -- ti
Orange
Green/white
-- +-I
Green
Blue/white
Blue
Brown/white
Brown
Power
supply
> ~

5.Diagrams
5.3 Diagram for 2 door station & up to 3 indoor phones
1.Connect 3 indoor phones and 2 door stations
as the diagram below.
2.Up, Down and PS terminals are useless here.
3.Max. Distance: <100m [In case longer,
please use an extra power supply on each
indoor phone.)
Oistributor (4230)
Orange/white 0 ~ ~
Orange
Green/white
Green
Blue/white
Blue
Brown/white
Brown
CAT.5
CAT.5
CAT.5
,..- --- - I ~r p ~ne 3
I ~
CI) °
e il.
o
s: N
Q. ~
'- °
o 11.
.g ~
E ~
L O
11.
N
§
~
Vi
o
o
o
~: :: J a.
LB
LA
PS~
GND 3:
DC+J
Power supply
Ooor station1 Door station2
5<

5.Diagrams
5.4 Diagram for e-locks
There are 2 wiring options for e-Iocks accordingly.
1. Release by POWER
2. Release by SIGNAL
I I +1Z\) I I +1Z\)
GS INO oo R GNO NO NC COM out
GS INOOOR GNO NO NC COM ou t
NO (Normal Op en )st yle
NC (NormalC lose ) style
[Note] Apower supply is required for the e-Iock in NO or Ne style.
If use an e-Iock that is without motor, a reverse diode (the producer
/
recommends IN4007) is required. It is usually enclosed when delivering.
3.EXIT button
+1ZV
EXIT button
-NO NC COM
out
[Note] No polarity requ ired .
> <

-6.Installation
•
Door station
Dimensions
150
N
I'-
N
@ @
Mounting
o
o
106
o
!
o
130
Product size:272x 150 x 68.5 mm
Installation size:254 x 132x 64 mm
*Notes:
1. Mind the installation size while producing a groove for the back cover.
2. Control the depth of the groove carefully so that it is as same as the one
of the
back cover.
3. We suggest the height between 1100mm and 1400mm. But please also consider
other situations such as view angle of the camera and disabled persons.
> <

6.Installation
• Power supply(4055)
Dimensions Mounting
}
)
• Power supply(4001 )&Distributor(411 OS /4230 )
Dimensions
4001
4110S
4230
38 . 5 ~
82
152
e '<IT e
"1
\1 '
e
ro-
0 e
Mounting
)
J

I 6.Installation
• Changing name tag
o
0 0
twJ
"!d:: ~ ~
o0
1.Push the right edge 2.Take off the
and move to right. plastic.
rJ
0 0
immmm
0 0
Plastic
q
[J
r10l
''*:'.:: ~ 2.
00
Name tag
3.Takeout the name tag.
o o o o
4.Put the name tag 5.lnsert the right
in the plastic. edge into sideling.
6.Push the left edge 7.Finish.
and move to left.

7.Camera adjustment
"" • "" . =
A:for up and down
,I
I , B:for left and right
,
Left Right

8.0peration
Please connect all necessary units according to the diagrams . When the door
station sounds "ON", it means the system is ready and you can use or program it.
• Call
1.Press CALL button on the door station, the indoor phone chime tone sounds and the screen
turns on and displays the visitor image.
2.lf there is no answer, the door station will say "Sorry. There is no answer" and the system
will automatically reset to standby after 30s . If the line is busy, the door station will speak
"Sorry. It's busy now."
[Note:if want to cancel the call,press CALL button again.]
• Answer
1 .press© button on the indoor phone (hands-free) or pick up the handset to answer when
it rings. [SPEAK NOWj LED will flash at the same time.
2
.PressS button on the indoor phone to release the door.
3 .Press© button on the indoor phone (hands-free) or hang up the handset to end the talk.
[Note: The talk is allowed in 120s.]
OR o
> <

8.0peration
• Ooor release
There are tour methods to release the door.
1./ndoorphone: Press8 button on the indoor phone to release the door.
2./0 Card: Put the registered eard on the eard reader (if there is) to release the door..
3.SERV/CE button: In the authorized time, press SERVICE button on the door station 10release
the door. [This button is special for postmen or other service people. The function has
to be programmed by the remote control, The remote control manual has details.]
4.EX/Tbutton: Press the EXIT button (if there is) to release the door.
[Note:when the
electronic lock ls released, the door station will say "the door opened"
and the [ODOR OPEN] LEO will flash at the same time.]
@
• Scan mon i tor
1.Press @ button on the (video) indoor phone while the system stands by, the sereen will
display the image in front of the door station. .
2.Press @ button again to end monitoring. But when there is another door station, if you
press the button at the 3rd time, it will display the image in front of that door station.
[Note:the image automatically turns off in approx . 15s. Ouring displaying, if somebody
presses the CALL button on the door station, the monitoring will end automatically.]
><

Appendix 1
Prepare for CAT.5cables with Rj45 connector
T568B standard is the most popular in network projects.
Materials and tools:
1II 11l 1l
RJ45 connector (8P) CAT.5 or CAT.5E 8P wire Crimpers Tester
'" TheC-5system always uses CAT.5 or water-proof CAT.5Ecables asthe following
ill pictures. 80th kinds of cables are required to be complied with the Internat-
ional Standard «TIAlEIA-568-B.2-2001 Commercial
Building Telecommunications
Cabling Standard Part 2: Balanced Twisted-Pair Cabling Components )) .
t
CAT.5 Water-proof CAT.5E
Sequence
of wires in T568B standard:
12 34 5 6 78 1.0range/white
2
.0 range
3.Green/white
4.Blue
5.Blue/white
6.Green
12 3 4 5 6 7 8
7.Brown/white
8.Brown

Process charts
Step1: Cut a wire which need to use
Step 3: Collocate and range the wires
according to the sequence mentioned
above.
Step 5: Take a connector and keep the hook
adown and facing to your body. Insert the
wires into the connector
until all wires touch
Step2:Cut the coat and take it off
Step 4: Cut the wires to be orderly.Please
mind the wires length to be about 15mm.
Step 6:lnsert the connector into the tool
and
press the tool to fix the wires in the
connector.
Step 7: repeat Step 1 - Step 6 for another end of the cable.
Step 8: use the tester to test if the wires at two ends are conjoint weil and corresponding each
other at right sequence..
<

Appendix 2
Product list
MODEL
5403
54030
5809/5809-C
58090/58090 -C
FEATURE
Audio
Speech system, proximity
Port for EXIT button
Striking name tag
Easy pragram with remote contra1
Audio
Speech system, praximity
ID card reader, SERVICE button
Port for EXIT button
Striking name tag
Easy pragram with remote contral
Video
Speech system, praximity
Port for EXIT button
Striking name tag
Easy pragram with remote contral
Video
Speech system, proximity
ID card reader, SERVICE button
Port for EXIT button
Striking name tag
Easy pragram with remote control
>