Genway WL-03NL User manual

WL/CM-03NL(E crust) Network video doorphone system
(Edition:V1.00)
Please don't abandon the products as wastes at will.
It should be recycled and disposed separately. Thanks!

52
Instructions for relay equipment wiring
¡
VM-03N video amplifier
Connect VCC,GND terminal with DC12V power's positive and negative polarity
respectively
(2)VFO,GND is one video output, connect with network equipment's TV+, TV-
respectively
(3)VF1~VF3, GNDare three video outputs, connect VF1~VF3 terminal with network
equipment's TV+, and connect GND terminal with network equipment's TV-
(4)VCOM,AUDIO+are three audio ports, it is convenient for user only, you can
connect audio wire with VM-03N, also you can select not connect audio wire
with VM-03N.
)?(
INDICATION
VM-03N
VIDEO AMPLIFIER
VF1 GND VF2 GND VF3 GND
GND VCC VCOMAUDIO+ VCOMAUDIO+ VCOMAUDIO+GNDVF0
3 audio prepared port,
can or not connect with
network equipment
audio terminal
12V power
VCOM
AUDIO+
VCOM
AUDIO+
VCOM
AUDIO+
VF0
GND
1 video output port,
connect with network
equipment's video
input terminal
3 video input port, connect with network
equipment video output terminal
¡
¡ ¡
¡ ¡
¡ ¡ ¡ ¡
¡ ¡
¡ ¡
¡ ¡
¡ ¡
VM-01T video sender & VM-01R video receiver
(1)VM-01T video sender: +12V,GND terminal connect respectively with DC12V
power's positive, negative polarity. VIDEO,GND connect with camera;
VIDEO+,VIDEO- connect with VM-01R's VIDEO+,VIDEO-
(2)VM-01R video receiver: +12V,GND terminal connect respectively with
DC12V power's positive, negative polarity. VIDEO,GND connect with CRT
or monitor's video input and video GND; VIDEO+,VIDEO- connect with
VM-01T's VIDEO+,VIDEO-
12V GND GNDVIDEO
VIDEO-VIDEO+
12V GND GNDVIDEO
VIDEO-VIDEO+
12V
GND
GND
VIDEO
Camera
12V
power
12V
GND
GND
VIDEO
CRT or
monitor
VIDEO+
VIDEO-
VIDEO+
VIDEO-
VM-01T video sender VM-01R video receiver
2-coaxial wire
Note: there is an electrograph(RV1), switch(SW1) in VM-01R video receiver's
electronics board, RV1 is whiteness adjuster, SW1 is color adjuster. Dial SW1
downward to switch it ON, normally, when distance is 500 m, 1 is ON, others are
OFF; When the distance is 800 m, 1 , 2 are ON, others are OFF; when the
distance is 1200 m, 1 , 2 , 3 are ON, others are OFF; when the distance is
1500 m, the above are ON( 1 , 2 , 3 are dialing times). Please select
accordingly when in actual use, and match RV1 to achieve the best video quality.
¡ ¡
¡ ¡ ¡ ¡
¡ ¡ ¡ ¡ ¡ ¡
¡ ¡ ¡ ¡ ¡ ¡
12V
power

1¡ ¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡1
¡ ¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡ ?
3¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡1
4¡Product structure and functions¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡
5¡System components and parameters¡¡¡¡¡¡¡¡¡¡¡¡¡¡
6¡ ¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡
1. ¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡
(1)Non-Network video system diagram¡¡¡¡¡¡¡¡¡¡¡¡
(2)Non-Network audio system diagram¡¡¡¡¡¡¡¡¡¡¡¡
2. ¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡
(1)Network video system diagram¡¡¡¡¡¡¡¡¡¡¡¡¡¡
(2)Network audio system diagram¡¡¡¡¡¡¡¡¡¡¡¡¡¡
3.Diagram for main indoor phone CM-02NLRaM¡¡¡¡¡¡¡¡
7¡System Wiring¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡
1.Non-network wiring for video system¡¡¡¡¡¡¡¡¡¡¡¡¡
2.Non-network wiring for audio system¡¡¡¡¡¡¡¡¡¡¡¡¡
3. ¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡
(1) ¡¡¡¡¡¡¡¡¡¡¡¡¡
¢ ¡¡¡¡¡¡¡¡
¢ ¡¡¡¡¡¡¡
¢ ¡¡¡¡¡¡¡¡¡
(2) ¡¡¡¡¡¡¡¡¡¡¡¡¡
¢ ¡¡¡¡¡¡¡¡
¢ ¡¡¡¡¡¡
¢ ¡¡¡¡¡¡¡¡¡
¡ ¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡
9¡Wiring Material¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡
10¡ ¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡
11¡ ¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡
12¡Installation¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡
1.Installation size¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡
2. ¡¡¡¡¡¡¡¡¡¡¡¡¡
¡ ¡¡¡¡¡¡¡¡¡¡¡¡¡¡
14¡ ¡
System introduction
2 System Characteristics
System constitution
System diagram
Non-Network system diagram
Network system diagram
Network system wiring
Network wiring for video system
Wiring between conformity unit and switch
Wiring among switch, door station and module
Wiring between module and indoor phone
Network wiring for audio system
Wiring between conformity unit and switch
Wiring among switch , module and door station
Wiring between module to indoor phone
8 Wiring Instruction
System setting
System operations
Door station's installation and notes
13 Instructions for easy malfunction
Supplemental manual for network relay equipment(attachments)
Contents
2
5
11-15
11-12
11
12
13-14
13
14
16-35
16
19
20-35
20
20
22
26
31-35
31
33
35
36
40
41
42
46-49
49
50
15
51
46
14¡Supplemental manual for network relay equipment(attachments)
Attached supplemental manual for network video door phone's relay equipments
Relay equipment features
¡
¡
VM-03N video amplifier: amplifies the video signal for long distances
VM-01T video sender & VM-01R video receiver: VM-01T is sending and VM-01R
is receiving, they must exist at the same time, it mainly solves the long-distance
-transferring-signal problem.
Relay equipment selection
¡
¡
¡
¡
Selection video relay equipment for network system
When transmitting video signal, if you are using branches, please select the VM-03N video
amplifier between the network equipments
When video transmission distance is equal or over 500 M, please select one VM-01T video
sender and one VM-01R video receiver between network equipments
When transmitting video signal, if you are using branches and the transmission distance is
more than500 M, please select VM-03N video amplifier, one VM-01T video sender and one
VM-01R video receiver between network equipments
¡VM-03N video amplifier:
¡T0?-VM video sender:
Indicator
VM-03N
VIDEO AMPLIFIER
VCOM
VF1 GND VF2 GND VF3 GND
GND VCC AUDIO+ VCOMAUDIO+ VCOMAUDIO+ VCOMAUDIO+GNDVF0
a) ?2VC¡?0?
b) ¡15mA
c) ¡120mA
Working voltage: D
Standby current:
Working current:
a) ?2VDC¡?0?
b) ¡200mA
c) ¡300mA
Working voltage:
Standby current:
Working current:
¡R0?-VM video receiver
a) ?2VDC¡?0?
b) ¡200mA
c) ¡300mA
Working voltage:
Standby current:
Working current:
Relay equipment technical parameters
VM- 01T
VIDEO SENDER
VM- 01R
VIDEO RECEIVER
51

1
1¡System Introduction
¡
¡
¡1/3 CCD
¡The door station has different password for users to unlock the door, three digits or four
digits Room No. optional..
¡
Encode construction, easily installation and debug.
The indoor phone is installed by hanging up, the door station or the management center
can call the indoor phone and can communicate with each other. This system has the
functions of alarm and remote control unlock.
' used in the door station, and LED enables users to identify visitors clearly
even at night.
One door station can connect 100 modules. One module can connect 4 indoor phones
which can be used in different floors.
2¡System Characteristic
¡
¡
¡Ding Dong or 3 different ring tones available.
¡
Durable materials have been used to encode a long life time.
Standby current consumes little electricity, economical electricity.
Different models indoor phone are optional.
3¡System Combination
¡
(1)Door station£CM-03NL¡CM-03NL-C¡CM-03NLA¡CM-03NLA-C
(2)Indoor phone£CM-02NLRG¡CM-02NLRG-C¡CM-02NLRH¡CM-02NLRH-C¡
CM-02NLRM¡CM-02NLRM-C¡CM-02NLRM1¡CM-02NLRM1-C¡
CM-02NLRaM¡CM-02NLRaM-C¡CM-02NLRbM¡CM-02NLRbM-C¡
CM-02NLRI¡CM-02NLRJ¡CM-02NLRV¡CM-02NLRV-C
(3)Module£CM-03NLCH-162 or CM-03NLCH
(4)Power£5-PSE¡PS-9
(5)Switch£CM-03NQH-1(1 )¡CM-03NQH-2( )¡
CM-03NQH-4(4 )¡CM-03NQH1-162(1 )¡
CM-03NQH2-162( )¡CM-03NQH4-216(4 )
(6)Conformity unit£CM-03NZH(1/2/4 )( )
(7)Management unit£CM-03NHMC( )
(8)Wall phone£CM-03NWD(A)(Optional)
System combination for video system:
route way 2 route way
route way route way
2 route way route way
route way used in network function
used in network function
¡
(1)Door station£WL-03NL¡WL-03NL-C¡WL-03NLA¡WL-03NLA-C
(2)Indoor phone£WL-02NLFD¡WL-02NLFH¡WL-02NLFC¡WL-02NLFH1¡WL-02NLFL
(3)Module£WL-03NLCH
(4)Power£2-PSE¡PS-5E¡PS-9
System combination for audio system:
Notice: For different purposes, we provide different switches and modules.
WL-03NQH-1/2/4 and CM-03NQH-1/2/4 are with iron shell. WL-03NQH1/2-162,
CM-03NQH1/2-162, WL-03NQH-216 and CM-03NQH-216 are with plastic shell.
They have 1, 2 and 4 route way for consumer's different purposes.
13 Instructions for easy malfunction¡
Door station
doesn't work
Check the system's power supply
indicator, see whether it light or not;
check the power wire's connection ways,
see whether it is right or wrong
All users of
whole building
can not unlock
Check whether the wire from door
station to power and power to electrical
lock is correct or not, whether the
electrical lock is compatible with the
system or not(this system is signal
-unlock), whether the door station's bus
wire is connected correct or not
Main wires are connected wrong. Short
circuit or broken wire.
Correct the connections according to the
connection map, and use another good m
achine to test.
The door station
cannot call all
indoor phones.
Power on the video amplifier,
connect the video amplifier's video
input and output port correctly with
indoor phone and test
Indoor phones
has raster but
no picture
If whole building's indoor phone hasn't
pictures, Please check whether the wiring
from door station video output VIDEO
to module video input is divided by
negative and positive accordingly or not.
If individual indoor phone hasn't
pictures, please check whether its
video-wiring is correct or not, or the
indoor phone is damaged or not. Also
please check the video amplifier is
power on or off, input and output port is
corrected right or not.
Malfunction reason Solving instructions
Malfunction
phenomenon
If indicator doesn't light, it represent power
off, according to correct diagram to connect
the power with door station.
Check if there is +12V output power at the
LOCK port of the door station when unlock.
If there is no power, change the door station.
If there is, check if the connection is correct
or if there is something wrong with the lock.
Connect the wires correctly according to
diagram, and change a good machine to
test
Can not
network with
management
unit
If all door stations can not network
with management unit, check
whether the management unit's bus
wire's connection is correct or not,
whether the management unit is
workable or not; if parts of door
stations can not network, please
check whether the network port ,
which is the nearest to the
management unit , is damaged or
not.
IC/ID card shall be less than 50 mm to
sensitive area. If all of cards can not
unlock, emphasize checking door station's
wiring; if individual card can not unlock,
it represent the card isn't registered or
canceled record or damaged.
IC/ID card
can not unlock
Whether they are registered or not;
whether they are damaged or not;
whether the reading ways is correct
or not; whether the door station is
damaged or not
50

2
Door Station
¨
4¡Product conformation and function
CM-03NL
ring)
S (only available at the system with ¡Melody¡et chord ring for door station:
¨
1
2
3
4
5
CM-03NLAWL-03NL
1
3
4
5
door station inside
Set: take off the back cover of the door station( as the figure shown)
there is a switch. The number(1~3) on the switch stands for
one melody ring. When you turn the switch to the one
you can choose one of the melody ring.
Logo
CCD
1
2
Speaker
Microphone
3
4
Keypad
Card reader
5
6
(5)Switch£WL-03NQH-1(1 )¡WL-03NQH-2(2 )¡
WL-03NQH-4(4 )¡WL-03NQH1-162(1 )¡
WL-03NQH2-162(2 )¡WL-03NQH4-216(4 )
(6)Conformity unit£WL-03NZH(1/2/4 )( )
(7)Management unit£WL-03NHMC( )
(8)Wall phone£WL-03NWD(A)(Optional)
route way route way
route way route way
route way route way
route way used in network function
used in network function
1
2
3
4
5
6
ON DIP
1 2 3 4 5 6 7 8
ON DIP
1 2 3 4 5 6 7 8
2.Door station's installation and notice:
(1)Drill a rectangular hole on proper position of the iron according to door station
installation size.
(2)Pull out the two small covers. Take off the screws with the attached inner
hexagon wrench, and then take off the door station back cover. Fix the back
cover on the iron door. Then lock the door station from the back cover with the
attached two M4 45 screws and fixed steel sheet.
(3)Push the small covers and firm it.
¡
Installation steps on iron door:
Installation steps on wall£
(1)
¦
¡
¡
Drill a rectangular hole on proper position of the wall according to door stati
on installation size.
(2)Drill four 6mm holes as the door station installation size on the groove. Fix
the back cover on the groove with the attached plastic tubes and screws
(¦4.2 40mm).
(3)Press the front cover on the back cover, then use 2 M4 25
inner hexagon screws to lock them.
Notes:
(?)
)Make sure that when you install the door station that is mounted closely to the2
door or wall there should be no gap
The holes should be drilled according to the size of door station and relative
.installation size on iron door or wall
. (3)install the door station on the side that usually closed
(4)Do not install the door station on where it is exposed to direct rain or sunlight
(5)CM?60~CM?40between : Installation height
¢Iron door
¢Door station's panel
¢Door station's back cover
¢4¡45 S
¢
crews
Small cover
¢
¢
¢
¢
¢
¢
¢
49
Infrared Status Power
Card

Indoor Phone
¨
CM-02NLRG
MONITOR
BUSY
POWER
1
2
3
4
6
5
9
8
MONITOR
CALL
UNLCOK
BUSY
POWER
1
5
7
2
3
4
6
9
8
CM-02NLRH
3
10
10
CALL
UNLOCK
Display screen
Monitor
Call
1
2
3
Unlock
Busy Indicator
Power Indicator
4
5
6
Volume
Contrast button
Brightness button
7
8
9
Call: call management unit by handing off the handset and pressing the call button; if
you only press the call button then it will be an emergency call.
3
Handset
10
£ £ £ £ £ £ £ £ £ £ £ £ £ £ £ £ £ £ £ £ £ £ £ £ £ £Note £
CM-02NLRM/CM-02NLRM1 CM-02NLRaM Main Indoor Phone
MONITOR
CALL
UNLOCK
BUSY
POWER
1
2
3
4
7
6
11
10
9
12
1
2
3
4
7
6
11
10
9
12
MONITOR
CALL
UNLOCK
BUSY
POWER
MANAGEMENT
TALK
5
8
Display screen
Monitor button
Call button
1
2
3
Unlock button
4
Call:(1)For normal indoor phone: take off handset for calling management unit;
otherwise for emergency call.
(2)For main indoor phone: internal call broadcase among extra indoor phones
in the same apartment.
3
Management
Power Indicator
Busy Indicator
5
6
7
Talk Indicator
8
Contrast button
Brightness button
Ringing Volume
9
10
11
Handset
12
£££££££££££££ Note £ £ £ £ £ £ £ £ £ £ £ £ £ £
Management:take off handset for calling management unit, For main indoor phone;
otherwise for emergency call
5
Indoor Phone
¨
Installation diagram£(2) Accessory£
Slip buckle
Spring
Self-buy accessory£
Step¢
Step¢
Step¢
Installation steps division£
Step1
Step3
U type
guide orbit
4¡40 screw
(E/AL NS 35)
(GB 99-86)
Press down to draw the slip buckle
Push inby
Step2
(6)Module and Network switch£
?¡ ¡ mm62 110 45
?62-NLCH03-CM
162 110 45¡ ¡ mm
2-?62NQH03-CM
2¡ ¡ mm16 110 45
4-2?6NQH03-CM
86¡86¡mm45
CM-03NLCH
WL-03NLCH
146¡86¡mm45
(5)Module£
Installation diagram£SizeModel
SizeModel Installation diagram£(1)
124 90 70.5¡ ¡ mm
124 90 70.5¡ ¡ mm
PS-2E
PS-5E
48

47 4
Indoor Phone
¨
CM-02NLRJ
1312
TALK
UNI-TALK
CALL
MONITOR
UNLOCK
MIC
BUSY
POWER
7
CM-02NLRI
1
2
4
3
TALK UNLOCKCALL UNI-
TALK
MONITOR
MIC
11
5
6
8
10
12
13
14
15
1
2 4 6 3 5
9
7
8
Í»
ÕÏ
µÔ
10
11
16
Display screen
Talk button
Mute button
1
2
3
Call button
4
Mute :mutes the indoor phone¡s loudspeaker.
3
Talk Indicator
Speaker
Microphone
9
10
11
Brightness button
Contrast button
Ringing Volume
Voice volume
13
14
15
Door panel
16
£££££££££££££ Note £ £ £ £ £ £ £ £ £ £ £ £ £ £
Monitor
Unlock button
Busy Indicator
5
6
7
Power Indicator
812
CM-02NLRV Indoor Phone¨
Display screen
Monitor button
Unlock button
1
2
3
Call button
4
Call: (1)To call management unit---first press talk button firstly, then press this button,
(2)For emergency call , press this button directly.
4
Silence button
Talk button
Speaker
5
6
7
Talk Indicator
8
Power Indicator
Brightness button
Contrast button
9
10
11
Ringing Volume
12
£££££££££££££ Note ££££££££££££££
Silence:Mutes the indoor phone' s loudspeaker.
5
Voice volume
Slide cover
13
14
17
9
8
14
5
6
12 1310 11
2
3
4
201 0 67¡8¡mm
WL-02NLFD
(4)Audio indoor phone£
144.5mm
Installation diagram£
216 94 59¡¡mm
WL-02NLFH
Size
Model
(3)Installation size and diagram of indoor phones£
205 220 65.5¡ ¡ mm
CM-02NLRG
224 218 59¡ ¡ mm
Installation diagram£SizeModel
CM-02NLRH
112mm
61mm
CM-02NLRH Holder CM-02NLRG Holder
210 220 68¡ ¡ mm
CM-02NLRM
235 200 8¡ ¡4 mm
Installation size£
CM-02NLRI
292 198 47¡ ¡ mm
CM-02NLRJ
CM-02NLRV
120mm
110mm
250 224 49¡ ¡ mm
Installation diagram:
(?)screws as the installation4 Fix the holder on a suitable position on wall with
.diagram
)2(Hang up the indoor phone on the holder¡
. (?)Do not install near moist place and burner
. (2)Do not install near the place where causes strong electrionic magnetic field
)Such as TV loudspeaker(¡
(3)Do not fall or punchy strike
. (4)Do not clean by wet cloth or volatile reagent
. (5)because of high voltage inside, Do not dismantle optionally
. (6)Keep the glass of the door station and indoor phone clean
Note:
Installation steps:
80
50
44
25
Size
Model
203 89 64¡¡mm
WL-02NLFC
220¡85.6¡49.5mm
WL-02NLFH1
WL-02NLFL 100¡210¡32.5mm

546
a)Working Voltage:V?8 DC¡10%
b)Standby Current:¡50mA
Viewing angle:92.8¡
Min Luminance:0.1Lux
Lens:F=3.6
Working Current)c:¡mA380
d( :?/3 CCDCamera '
5 System components and parameters:¡
CM-03NL Video Door Station
1.
a)Working Voltage:18V DC¡?0?
Module
b)Standby Current:¡8mA
c)Working Current:¡170mA
3.
e)Environment Temperature:-25¡+70¡
f)Humidity:45%¡95%
a)Working Voltage:?2VDC¡10%
b)Standby Current:¡75mA
c)Working Current:¡mA250
25:-Environment Temperature)d¡+70¡
WL-03NL Audio Door Station
2.
e)Humidity:45%¡95%
a)AC Input Voltage: 23V0 AC
PS-5E Power
b)DC Output Voltage:V?8 DC/800mA
+10%
-15%
4.
?62-NLCH03-CM NLCH03-CM
Indication
CM-03NLCH-162
Setup
A+18VAFOUT DATA AGNDMONI V+18V VGNDTVOUT T&R MONIAGND V+18V VGND TV A+18V GND T&RMONI AGNDV+18V VGND TV A+18V
A+18V AFIN DATA AGND MONIV+18V VGND TVIN T&R MONIAGNDV+18V VGND TV A+18V GND T&R MONIAGNDV+18V VGND TV A+18V
Setup
CM-03NLCH
Indication
¡
+DC-
¡AC¡
TRANSFORMER
Model£PS-5E
Input£230V¡50Hz
Output£18V 800mA
Notes:Used in indoor
12¡Installation
?.Installation size：)aluminum alloy cover length=L(
W2
W3
L2=(L+24)
L3
W1
90
L1=(L+26)
Model Cover length
L(mm)
Door station
size(mm)
NLA03-WL
348¡140¡52
312
348
340)?L(¡???)?W(¡? ?)?D(
376)?L(¡?08)?W(¡38)?D(
Installation size on
iron door (mm)
Installation size
on wall(mm)
338)?L(¡???)?W(¡? ?)?D(
374)2L(¡?26)2W(¡42)2D(
Installation size on iron door Installation size on wall
NL03-CM
(1)Installation size table for aluminum alloy door station series£
D2
D1
384¡140¡52
NLA03-CM 388 416)?L(¡???)?W(¡??)?D(
424¡130¡52 416)?L(¡???)? W(¡)?D(
NL03-WL 304¡?¡?? 268 296)?L(¡???)?W(¡? ?)?D( 2?4)2L(¡?26)2W(¡42)2D(
(2)Power and CM-03NQH network switch£
CM-03NQH 240 176 71¡ ¡ mm
Installation diagram£
Installation size:
PS-9 383¡?8?¡mm7?
SizeModel
CM-03NZH(1/2) 383¡?8?¡mm7?
PS-2
PS-5A-3
179 189 70¡ ¡ mm
283 189 71¡ ¡ mm
250mm
145mm
2-PS 3-A5-PS
161mm
NQH03-CM
310mm
?-PS or
?/2(NZH03-CM(

6
45
a)Working Voltage:18VDC¡10%
CM-02NLRG/CM-02NLRG-C Indoor Phone
b)Standby Current:¡15mA
c)Working Current:¡50mA0
d)Kinescope:4 £Resolution>450 lines£' flat tube(B/W)
MONITOR
CALL
UNLOCK
BUSY
POWER
5.
Resolution:480¡250 points£
e)Color Display:4 £' color LCD display
f)Environment Temperature:-10¡+55¡£
g)Humidity:45%¡95%£
a)Working Voltage:18V DC¡10%
C Indoor Phone-NLRH02-CM/NLRH02-CM
b)Standby Current:¡15mA
c)Working Current:¡500mA
d)Kinescope:4 £Resolution>450 lines£' flat tube(B/W)
6.
Resolution:480¡250 points£
e)Color Display:4 £' color LCD display
f)Environment Temperature:-10¡+55¡£
g)Humidity:45%¡95%£
MONITOR
CALL
UNLOCK
BUSY
POWER
a)Working Voltage:18V DC¡10%
C Indoor Phone-NLRM02-CM/NLRM02-CM
b)Standby Current:¡15mA
c)Working Current:¡500mA
d)Kinescope:4 £Resolution>450 lines£' flat tube(B/W)
7.
Resolution:480¡250 points£
e)Color Display:4 £' color LCD display
f)Environment Temperature:-10¡+55¡£
g)Humidity:45%¡95%£
MONITOR
CALL
UNLOCK
BUSY
POWER
(2)Surveillance on indoor phone
¢Press the Monitor button, you can monitor the door entry. After 15 seconds, it will
be automatically shut down. If you want to quit the surveillance, just press the
Monitor button again.
¢If the system connects with a front door station, you can monitor the two door entries
circular order. If you want to monitor the main door entry, please press the Monitor
button just one time. If you want to monitor the front door entry, please keep pressing
the button more than 2 seconds.
¢If there are two or more indoor phones, the system allows only one to surveil the door
entry at a time, and the other indoor phones Busy indicators will lights and cannot
call each other during surveillance.
¢During monitoring the door station, the main indoor phone can listen in the door
station. Press¡Call¡button can talk with the door station and unlock the door.
(3)Broadcasting between the indoor phones
¢Pick up the handset, the indoor phone's Talk indicator will light, press the Call
button for seconds and release, then broadcasting is begin, meanwhile other indoor
phone's busy indicators will flash, and the indoor phones give ring. The
broadcasting time is 30 seconds.
¢Other hosts can pick up the handsets to answer when they receive the broadcasting.
The conversation time is 120 seconds. During the period, the other indoor phones which
handsets are not pick up stop ringing automatically, but their Busy in dicators keep
lighting. When the broadcasting or conversation time is up, the system will be shut
down automatically.
¢During intercommucating, if somebody call the door station, the system will switch
directly to the talking between the door station and the indoor phone.
(4)Call the management unit from main indoor phone: pick up the main indoor phone's
handset, press the Management button, the management unit rings (you can hear the
echo). If nobody answers, the system will be automatically shut down after 30 seconds.
(Remarks: extra indoor phones do not have this function, but the main indoor phone
can connect the line to extra indoor phones).
(5)Main indoor phone alarm: Do not pick up the handset, just press the Management
button, the management unit can receive the alarm message. (Remarks: this function is
only available for the main indoor phone).
¡ ¡
¡ ¡
¡ ¡
¡ ¡
¡ ¡ ¡ ¡
¡ ¡
¡ ¡
¡ ¡
¡ ¡
¢Pick up the handset of the ringing phone, you can talk with the calling indoor phone about 120sec.
you can also talk with the door station (during this time, you can hear the¡busy line¡indication).
When the calling indoor phone hangs up, the called indoor phone can talk with the door station.
¢If the system connects with a front door station, the operation is the same with the door
station, the only difference is that you have to keep pressing the Unlock button for
more than 3 seconds, otherwise you cannot unlock for visitors.
¡ ¡

44
7
a)Working Voltage:18V DC¡10%
C Main Indoor Phone-NLRaM02-CM/NLRaM02-CM
B)Standby Current:¡90mA
c)Working Current:¡83mA0
d)Kinescope:4 £Resolution>450 lines£' flat tube(B/W)
8.
Resolution:480¡250 points£
e)Color Display:4 £' color LCD display
f)Environment Temperature:-10¡+55¡£
g)Humidity:45%¡95%£
a)Working Voltage:18V DC¡10%
Free Indoor Phone-NLRI Hands02-CM
b)StandbyCurrent:¡15mA
c)Working Current:¡50mA0
d)Color Display:4 £' or 5.6' color LCD display
10.
Resolution:480¡250 points
e)Environment Temperature:-10¡+55¡£
f)Humidity:45%¡95%£
TALK
UNI-TALK
CALL
MONITOR
UNLOCK
MIC
BUSY
TALK
a)Working Voltage:18V DC¡10%
C Extra Indoor Phone-NLRbM02-CM/NLRbM02-CM
b)Standby Current:¡90mA
c)Working Current:¡830mA
d)Kinescope:4 £Resolution>450 lines£' flat tube(B/W)
9.
Resolution:480¡250 points;
e)Color Display:4 £' color LCD display
f)Environment Temperature:-10¡+55¡£
g)Humidity:45%¡95%£
MONITOR
CALL
UNLOCK
BUSY
POWER
MANAGEMENT
TALK
MONITOR
CALL
UNLOCK
BUSY
POWER
TALK
3.CM-02NLRaM/02NLRbM Video indoor phone operation
(1)
¡ ¡
¡ ¡
¡ ¡
¡ ¡
¡ ¡
Call from door station:
¢Press the room number button on the door station, all of the indoor phones in the room
ring, meanwhile the screens display the visitor's image, and the Busy indicators
flash. If nobody answers, the system will be automatically shut down after 30 seconds.
¢Pick up the handset and talk with the visitor (at the moment, the Talk indicator
lights).The other indoor phones will be shut down and the Busy indicators will keep
lighting. During the conversation, press the Unlock button, you can unlock for the
visitor.
¢If you want to connect the line to another indoor phone when you are talking with the
visitor, just press the Call button, then the other indoor phones will ring, meanwhile
the door station gives voice.
(3) ¡ ¡
¡ ¡
¡ ¡
¡ ¡
¡ ¡
Door station call indoor phone in the same building: press * and input the room
No. that's all. For example: If you want to call NO. 102 family, when room number is
three digits: press Room No. 102 ; When room number is four digits, press Room
No. 0102 If the Room No. is right, the indoor phone will ring, the host can pick up
the handset(if for handfree indoor phone, press button TALK )to talk with the visitor.
And the conversation time limit is 120 seconds. When time is up, the door station will
switch off automatically, if you want to continue talking, please call again. If nobody
answer the indoor phone, the door station (with ring) begin to count down 30 seconds
and after 30 seconds', the door station will shut down automatically. If you input the
wrong room number, the door station will display Err and shut down automatically.
Note: The following functions only comes into effect when in the network system.
(4)Calling from door station to management unit: just press the Management Unit No.
on the door station, for example, if you want to call No.01 Management Unit, just
press * + 01+# ,( if the room number is just 2 digital, you just need dial *+#+01
to call management unit by door station),the Management Unit will ring, person in
charge of the Management Unit can answer the phone, the conversation time limit is 120
seconds. If nobody answers the phone or the line is busy, the management unit will quit in
30 seconds. The management unit can unlock the door for the Called door station.
(5)Indoor phone calls management unit: pick up the handsetof the indoor phone (if for
handfree indoor phone, press button TALK ) and press or CALL button,
the management unit will ring, person in charge of the management unit can answer the
phone. If nobody answers the phone or the line is busy, the management unit will quit in
30 seconds.
(6)Indoor phone call for help: press or CALL button, the management unit will
receive the help massage.
Note: when debugging, if there are more than one same room numbers in one system,
you can not call the indoor phone.
¡ ¡
¡ ¡ ¡ ¡
¡ ¡
¡ ¡ ¡ ¡ ¡ ¡
¡ ¡ ¡ ¡

43 8
a)Working Voltage:18V DC¡10%
Free Indoor Phone-C Hands-NLRV02-CM/NLRV02-CM
b)Standby Current:¡15mA
c)Working Current¡500mA
d)Kinescope:4 £' flat tube(black/white)
12.
Resolution:480¡250 points
f)Environment Temperature:-10¡+55¡£
g)Humidity:45%¡95%£
e)Color Display:4 £' color LCD display
a)Working Voltage:18V DC¡10%
Free Indoor Phone-NLRJ Hands02-CM
b)Standby Current:¡15mA
c)Working Current¡50mA0
d)Color Display:4 £' or 5.6'color LCD display
11.
Resolution:480¡250 points
e)Environment Temperature:-10¡+55¡£
f)Humidity:45%¡95%£
TALK UNLOCKCALL UNI-
TALK
MONITOR
MIC
TALK
BUSY
POWER
a)Working Voltage:18V DC¡10%
Network Switch For Video System
b)Standby Current:¡mA50
c)Working Current¡mA500
13.
a)AC Input Voltage:23V0 AC
PS-9 Power(UPS)
b)DC Output Voltage:
+10%
-15%
14.
A?.5/V?2
A0.5/V6
CM-03NQH2-162
NETWORK SWITCH
POWERGND AF DATA TV+ TV- MONI GND AF DATA TV+ TV- +18V
LA LBAI1+ AI1- VI1+ VI1- AI2+ AI2- VI2+
+18VPOWERGND AF DATA TV+ TV- MONI +18V
VI2- COMAO1+AO1- VO1+ VO1- AO2+ AO2- VO2+ VO2-
CM-03NQH
NETWORK SWITCH
CM-03NQHCM-03NQH2-162
+10%
-15%
PS-9 POWER SUPPLY
AC input:230V
A?.5 /V?2
6V/0.5A
DC output£
Protection Grade:IP30
¡
2.Audio system operation:
(1) ¡ ¡
¡ ¡ ¡ ¡
¡ ¡
¡ ¡
¡ ¡
(2) ¡ ¡ ¡ ¡
¡ ¡
¡ ¡
¡ ¡
¡ ¡
Password to unlock the door station: Press *+ F4 , the door station will display
Addr , enter the room No.(3-digit or 4-digit), If the door station displays Pd-p ,
Please enter password (the default password is 1234), Then the door station displays
Pass indicates successful unlock. If enter the wrong room number, the door station
will display 'Err and shut down automatically. If you enter the wrong unlock password,
the door station will display Pd-p . If you enter wrong unlock password more than five
times at the same time, the door station will shut down automatically.
(Note: when the system operate in a network if users key a wrong password more
than 5 times at one time. then the door station will give an alarm to the management
unit automatically
Change unlock password: Press *+ 3 + F3 , the door station displays Addr ,
enter the room No. ( 3-digit or 4-digit), door station displays Pd-p , enter old unlock
password, then door station displays Pd-n , please enter new password, If the door
station displays Pass , which indicates the unlock password successful change. If you
enter the wrong room NO and password, the door station will display Err and shut
down automatically.
(4) ¡ ¡
¡ ¡
¡ ¡
¡ ¡ ¡ ¡
¡ ¡
¡ ¡
¡ ¡
Monitor function: press the Monitor button in the indoor phone, you can see the
condition outside door for 15 seconds. If you want to cancel the monitor, just press the
Monitor button again. (Note: If somebody calls another indoor phone at this time,
the monitor function will be off.)
Note: The following functions only comes into effect when in the network system.
(5)Calling from door station to management unit: just press the Management Unit No.
on the door station, for example, if you want to call No.01 Management Unit, just
press * + 01+# ,( if the room number is just 2 digital, you just need dial *+#+01
to call management unit by door station),the Management Unit will ring, person in
charge of the Management Unit can answer the phone, the conversation time limit is 120
seconds. If nobody answers the phone or the line is busy, the management unit will quit
in 30 seconds. The management unit can unlock the door for the Called door station.
(6)Indoor phone calls management unit: pick up the handset, press Call button, the
management unit will ring, person in charge of the management unit can answer the
phone. If nobody answers the phone or the line is busy, the management unit will quit in
30 seconds.
(7)Indoor phone call for help: press Call button, the management unit will receive the
help massage.
Note: when debugging, if there are more than one same room numbers in one system,
you can not call the indoor phone.

942
CM-03NZH Conformity Unit(4 )route way
15.
b)Standby Current:¡85mA
c)Working Current:¡500mA
a)Working Voltage:V DC?2¡?0?
V DC6¡?0?
CM-03NHMC Management Unit
16.
b)Standby Current:¡120mA
c)Working Current:¡800mA
a)Working Voltage:18VDC¡10%
CM-03NWD(A) Wall Phone
17.
b)Standby Current:¡75mA
c)Working Current:¡350mA
a)Working Voltage:18V DC¡10%
1 2 3 A
4 5 6 B
7 8 9 C
* 0 # D
a)Working Voltage:12VDC¡10%
Network Switch For Audio system
b)Standby Current:¡55mA
c)Working Current:¡1mA00
18.
WL-03NQH
NETWORK SWITCH
WL-03NQHWL-03NQH2-162
WL-03NQH2-162
NETWORK SWITCH
GND AF DATA
LA LBAI1+ AI1-
POWERGND AF DATA
COMAO1+AO1- AI2+AI2-AO2+ AO2-
POWERGND AF DATA
11¡System operation
?.Video system operation：
3.How to adjust the tones£Uncover the door station.) (£
tone with the four holes.
The back cover of the door station
ON DIP
1 2 3 4 5 6 7 8
1
23 4
Position ?£adjuster for the d
position 2£adjuster for the i
position 3£adjuster for the i
position 4£adjuster for the d
oor station speech volume
ndoor phone ring volume
ndoor phone speech volume
oor station feed-back ring volume
(1) ¡ ¡
¡ ¡ ¡ ¡
¡ ¡
¡ ¡
¡ ¡
(2) ¡ ¡ ¡ ¡
¡ ¡ ¡ ¡
¡ ¡
¡ ¡ ¡ ¡
¡ ¡
¡ ¡ ¡ ¡
) ( ¡ ¡
¡ ¡
¡ ¡
¡ ¡
Password to unlock the door station: Press *+ F4 , the door station will display
Addr , input the room No.(3-digit or 4-digit), If the door station displays Pd-p ,
Please input password (the initialization passord is 1234), Then the door station displays
Pass indicates successful unlock. If input the wrong room number, the door station
will display 'Err and shut down automatically. If you input the wrong unlock password,
the door station will display Pd-p . If you input wrong unlock password more than five
times at the same time, the door station will shut down automatically.
(Note: when the system operate in a network if users key a wrong password more
than 5 times at one time. then the door station will give an alarm to the management
unit automatically
Change unlock password: Put the Jb1 in the module to the SET position press
*+ 3 + F3 , the door station displays Addr , input the room No. ( 3-digit or 4-digit),
door station displays Pd-p , input old unlock password, then door station displays
Pd-n , please input new password, If the door station displays Pass , which
indicates the unlock password successful change. If you input the wrong room NO and
password, the door station will display Err and shut down automatically. When
finished the setting, put the JB1 in the module to the COM position.
Door station call indoor phone in the same building: press * and input the room
No. that's all. For example: If you want to call NO. 102 family, when room number is
three digits: press Room No. 102 ; When room number is four digits, press Room
No. 0102 If the Room No. is right, the indoor phone will ring, the host can pick up
the handset to talk with the visitor. And the conversation time limit is 120 seconds.
When time is up, the door station will switch off automatically, if you want to continue
talking, please call again. If nobody answer the indoor phone, the door station (with
ring) begin to count down 30 seconds and after 30 seconds', the door station will shut
down automatically. If you input the wrong room number, the door station will display
Err and shut down automatically.

10
a)AC Input Voltage:2AC3V0
PS-2E Power
b)DC Output Voltage:?DC3.5V/800mA
+10%
-15%
WL-03NLCH Module
21.
22.
a)Working Voltage:DC12V¡10%
Audio Indoor Phone
b)Static Current:0
c)Working Current:¡2mA0
19.
WL-02NLFD WL-02NLFH
a)Working Voltage:DC12V¡10%
b)Static Current:¡8mA
c)Working Current:¡25mA
WL-03NZH Conformity Unit( )4 routeway
23.
a)Working Voltage:
b)Static Current:¡85mA
c)Working Current:¡400mA
V?2DC¡?0?
V6DC¡?0?
Setup In dicati on
WL- 03N LCH
¡
Note: above¡¡¡partial explanation and input voltage, the voltage can be
set according to different region countries.
¡AC¡
+DC-
TRANSFORMER
Model£PS-2E
Input£230V 50¡60Hz
Output£13.5V 800mA
Notes:Used in indoor
¡AC¡
WL-02NLFC WL-02NLFH1
a)Working Voltage:DC12V¡10%
WL-02NLFL Audio Indoor Phone
b)Static Current:¡20mA
c)Working Current:¡6mA0
20.
POWER TALK
1. ¡ ¡ ¡ ¡
¡
2. ¡ ¡
¡ ¡
¡ ¡
¡ ¡
¡ ¡
¡ ¡
¡ ¡
¡ ¡
¡ ¡
¡ ¡
¡ ¡ ¡ ¡
¡ ¡
¡ ¡ ¡ ¡ ¡ ¡
Set door station No.: Put the JB1 in the network switch to SET position. Press
* +1+ F3¡, the door station shows ¡Addr¡, input door station No., You can hear a
suggestive sound of ¡du¡, it means the setting is ok. When finish setting, put the ¡JB1¡
in the network switch to ¡COM¡position. Commonly the door station No. is 4- digit
number, If the number with letters , One letter is equal to two digits, such as 0008, 02B.
(Note: This only need to set when in network system, and its function only become
effective in the NETWORK system ).
Set Room No.: uncover the module, put the module's pin cap at SET position then
lightly poke the SETUP hole on the surface of module with a ball pen, the module's
indicator flickers quickly, the door station will display Addr ,type 3-digit or 4-digit
room No. on the door station , (the Room No. is decided by the door station) and the door
station will display Port , then enter one module terminal number(one digit number
from 1-4), if door station displays Addr again, that indicates the room No. has been
set, you can continue to type the next room No., If door station displays Err and then
Addr , that means you failed to set the room NO., re-enter again. When finished room
number setting, press SET button on the module, if the indicate light is flickering
slower, then you can quit the setting. Put the pin cap to the COM position to avoid the
losing of the room number. (Please note: one module can set 4 room numbers at most,
all initialization unlock passwords are 1234.)
For example: If set Room No. 101, operate as below, Press SET button on the surface
of the module which the indoor phone 101 connects to, the indicator will flicker quickly, the
door station will display Addr Input 0101; the door station will display Port Input
Port No. 1 which the indoor phone connects to accordingly, the door station will display
1 first then Addr , this means setting successfully. Press SET button, the
indicate light is flickering slower, which means you are quitting the setting.
Note: when set user number in the module, connect one module with door station, set
room numbers follows above, after finishing, take away the IC memory (U3, it is used to
memorize the set room info) and mark it (the port and its number). Then insert another
IC memory to this module and follow above instruction one by one until you finish all
room number. Then insert the set IC memory into modules of the corresponding floors.
It is the most efficient way to set room number.
+AI1- +VI1- +AI2- +VI2- +AI3- +VI3- +AI4- +VI4- COMLB LA
+AO1-+VO1- +AO2-+VO2- +AO3-+VO3- +AO4- +VO4-
POWERGND AF DATA TV+ TV- MONI+18V +18V GNDAFDATATV+TV-MONI POWER
MONI TV- TV++18V DATA AF GND
JB1
COMSET
JB1
COMSET
CM-03NQH inside view
CM-03NQH2-162
NETWORK SWITCH
POWERGND AF DATA TV+ TV- MONI GND AF DATA TV+ TV- +18V
LA LBAI1+AI1- VI1+ VI1- AI2+ AI2- VI2+
+18VPOWERGND AF DATA TV+ TV- MONI +18V
VI2- COMAO1+AO1-VO1+ VO1- AO2+ AO2- VO2+ VO2-
JB1
COMSET
1.T&R
2.MONI
3.AGND
4.+18V
5.VGND
6.TV CN1CN2 CN3 CN4
AFOUT
A+18VAFIN DATAAGNDMONIV+18VVGNDTVIN TVOUT
COMSET
JB
Setup
Button
COMSET
A+18VAFOUTDATA AGND MONI V+18V VGNDTVOUT T&R MONIAGND V+18V VGND TV A+18V GND MONIAGNDV+18V VGND TV A+18V
A+18V AFIN DATA AGND MONI V+18V VGND TVIN T&R MONIAGNDV+18V VGND TV A+18V GND T&RMONIAGNDV+18V VGND TV A+18V
T&R
Indication
CM-03NLCH-162
Setup
COMSET
Port1 Port2
Port3 Port4
10¡System setting(video/audio system are same)
CM-03NQH2-162 CM-03NLCH2-162 CM-03NLCH
41

11 40
Video Wire
CM-02NLRV or
CM-02NLRV-C
Electrical Lock
2
MONITOR
CALL
UNLOCK
BUSY
POWER
TALK
UNI-TALK
CALL
MONITOR
UNLOCK
MIC
BUSY
TALK
CM-02NLRI
CM-02NLRG or
CM-02NLRG-C
MONITOR
CALL
UNLOCK
BUSY
POWER
CM-02NLRM or
CM-02NLRM-C
2
4
4
2
Video Wire
66
6
6
PS-5E Power
2
PS-5E Power
Indication
CM-03NLCH-162
Setup
A+18VAFOUT DATA AGND MONI V+18V VGND TVOUT T&R MONIAGNDV+18V VGNDTV A+18V GND T&R MONIAGNDV+18V VGND TV A+18V
A+18V AFINDATA AGNDMONI V+18VVGND TVIN T&R MONIAGNDV+18V VGNDTV A+18V GND T&R MONIAGNDV+18V VGND TV A+18V
Indication
CM-03NLCH-162
Setup
A+18VAFOUT DATA AGND MONI V+18V VGND TVOUT T&R MONIAGNDV+18V VGNDTV A+18V GND T&R MONIAGNDV+18V VGND TV A+18V
A+18V AFINDATA AGNDMONI V+18VVGND TVIN T&R MONIAGNDV+18V VGNDTV A+18V GND T&R MONIAGNDV+18V VGND TV A+18V
6¡System diagram
1. £Non-Network system diagram
(1)Non-Network video system diagram£
Door Station
+DC-
¡AC¡
TRANSFORMER
Model£PS-5E
Input£230V¡50Hz
Output£18V 800mA
Notes:Used in indoor
+DC-
¡AC¡
TRANSFORMER
Model£PS-5E
Input£230V¡50Hz
Output£18V 800mA
Notes:Used in indoor
9¡Wiring Material
Mo-
del Wire material requirements(vertical square) Remarks
Video system
Diagram
Between door
station and
module
Between door
station and power
supply
¡30M
RVV6¡0.75mm
2
¡100M
RVV2¡1.0mm 2
¡10M
RVVP6¡0.75mm
RVVP5¡1.0mm
2
2
Between
module
and
indoor
phone
RVV4¡0.5mm +SYV75-5/96
2
¡30M ¡100M
Hand-set
indoor
phone
Hand-free
indoor
phone RVV6¡0.75mm +SYV75-5/96
2
RVV4¡1.5mm +SYV75-5/96
2
RVV6¡1.5mm +SYV75-5/96
2
¡10M
¡100M
¡800M
¡200M
Between
Conformity unit
and management
unit
Between door
station and module
¡30M
RVV4¡0.5mm
2
¡100M
RVV4¡1.0mm
2
¡30M
¡100M
¡100M
¡200M
RVV2¡0.3mm
RVVP4¡0.75mm
2
2
RVV2¡1.0mm
2
Among switch ,
door station and
module
Between Network
switch and
Conformity unit s
BUS board
'
When 4 rout ways
three wires are data wire and eight wires are audio
wire in the 11-core wire
When 3 rout ways
three wires are data wire and six wires are audio
wire in the 9-core wire
When 2 rout ways
three wires are data wire and four wires are audio
wire in the 7-core wire
When 1 rout ways
three wires are data wire and two wires are audio
wire in the 5-core wire
£RVVP11¡1.0mm
SYV75-7/128
(
£RVVP9¡1.0mm +3 video wires
SYV75-7/128)
(
£RVVP7¡1.0mm +2 video wires
SYV75-7/128(
(
£RVVP5¡1.0mm +1 video wires
SYV75-7/128)
(
+4 video wires
)
Between Network
switch and
Conformity unit s
BUS board
'
When 4 rout ways RVVP11¡1.0mm shield wire three wires are
data wire and eight wires are audio wire in the 11-core wire
When 3 rout ways RVVP9¡1.0mm shield wire three wires are
data wire and six wires are audio wire in the 9-core wire
When 2 rout ways RVVP7¡1.0mm shield wire three wires are
data wire and four wires are audio wire in the 7-core wire
When 1 rout ways RVVP5¡1.0mm shield wire three wires are
data wire and two wires are audio wire in the 5-core wire
£ (
)
£ )
(
£ )
(
£ )
(
¡800M
RVVP5¡1.0mm
2
RVVP4¡1.0mm
2
SYV75-5/96 PCS¡
RVVP6¡1.0mm
2
SYV75-5/96 PCS¡
SYV75-7/128 PCS¡
SYV75-5/96 PCS¡
RVV6¡1.5mm
2
SYV75-5/96 PCS¡
Note:(1)in this charts, RVVP represent the shield-wire
(2)Actual wire depended on capacity of the project! When exceed the ordered distance, please enlarge the square accordingly
(3)when network, if the total distance is exceed 200M, please add one video amplifier and repeaters. (4)the parameter in this chart is only for reference, our company reserve the right to change and explain.
Between door
station and
electrical lock RVV2¡1.0mm 2
Between
conformity and
management unit
Audio system
Among switch ,
door station and
module
RVV4¡0.3mm
2RVV4¡1.0mm 2
Between
module
and
indoor
phone
Hand-set
indoor
phone
Hand-free
indoor phone
12V
Power

39 12
Electrical Lock
Door Station
PS-2E Power
2
2
(2)Non-Network audio system diagram£
¡AC¡
+DC-
TRANSFORMER
Model£PS-2E
Input£230V 50¡60Hz
Output£13.5V 800mA
Notes:Used in indoor
¡AC¡
WL-03 NL CH
4
4
WL-03NLCH
WL-03 NL CH
WL-02NLFC
WL-02NLFH1
2
2
2
WL-02NLFD
WL-02NLFL
4
¢Wiring between switch and door station, module:
POWER
Audio
power
AF
Audio
DATA
Data
GND
Audio
GND
POWER AF DATA GND
Door
Station
Network
Switch
Module
VCC AF DATA GND
¢Wiring between switch and
extra door station:
AF
Audio
DATA
Data
GND
Audio GND
AF DATA GND
Extra
Door
Station
(2)Wiring between switches and among switch, door station, module, and conformity unit:
LA
Data A
LB
Data B
COM
Common
terminal
AI1+
Audio input
for No.1
route way
AI1- AI2+ AI2-
Network
Switch
LA LB COM AO1+ AO1- AO2+ AO2-
¢Wiring between switch and conformity unit (BUS board):
(3)Wiring between conformity unit's PORT board and management unit:
LA
Data A
LB
Data B
COM
Common
terminal
AF+ AF-
OR BK BL GR YL
Audio Audio GND
¢Wiring among switches:
Network
Switch
Audio GND
input for No.1
route way
Audio input
for No.2
route way
Audio GND
input for No.2
route way
Data A Data B Common
terminal
Audio output
for No.1
route way
Audio GND
output for No.1
route way
Audio output
for No.2
route way
Audio GND
output for No.2
route way
Network
Switch
Audio Data Audio GND
Audio
power Audio Data Audio
GND
Audio
power Audio Data Audio
GND
LA
Data A
LB
Data B
COM
Common
terminal
AI1+
Audio input
for No.1
route way
AI1- AI2+ AI2-
Network
Switch
LA LB COM AF1+ AF1- AF2+ AF2-
Conformity
unit s BUS
board
'
Audio GND
input for No.1
route way
Audio input
for No.2
route way
Audio GND
input for No.2
route way
Data A Data B Common
terminal
Audio for
No.1 route
way
Audio GND
for No.1
route way
Audio for
No.2 route
way
Audio GND
for No.2
route way
Conformity
unit s PORT
board
'
Management
unit
box
'switch Data A Data B Common
terminal Audio Audio GND
12V
Power

13 38
NONITOR
CALL
UNLOCK
BUSY
POWER
TALK
UNI-TALK
CALL
MONITOR
UNLOCK
MIC
BUSY
TALK
CM-02NLRI
CM-02NLRG or
CM-02NLRG-C
MONITOR
CALL
UNLOCK
BUSY
TALK
CM-02NLRJ
TALK UNLOCKCALL UNI-
TALK
MONITOR
¿·
TALK
BUSY
POWER
4+1
6+1
2
4+1 6+1
6+1 6+1
BUS1 BUS1
BUS1
2
WL-02NLFD
5+1
Electrical Lock
2
PS-5E Power
2
CM-03NWD(A) Wall phone
CM-03NHMC
Management Unit
CM-02NLRM or
CM-02NLRM-C
BUS8
CM-03NQH
NETWORK SWITCH
2
Module
Network
Switch
4
PS-9 5+1 5+1
6+1 6+1
2
2
Door Station
2
+10% -15%
PS-9 POWER SUPPLY
AC input:230V
A?.5/V? 2
6V/0.5A
DC output£ Protection Grade:IP30
CM-03NQH2-162
NETWORK SWITCH
POWERGND AF DATATV+ TV- MONI GND AF DATA TV+ TV- +18V
LA LBAI1+ AI1- VI1+ VI1- AI2+ AI2- VI2+
+18VPOWERGND AF DATATV+ TV- MONI+18V
VI2- COMAO1+AO1- VO1+ VO1- AO2+ AO2- VO2+ VO2-
CM-03NQH2-162
NETWORK SWITCH
POWERGND AF DATATV+ TV- MONI GND AF DATA TV+ TV- +18V
LA LBAI1+ AI1- VI1+ VI1- AI2+ AI2- VI2+
+18VPOWERGND AF DATATV+ TV- MONI+18V
VI2- COMAO1+AO1- VO1+ VO1- AO2+ AO2- VO2+ VO2-
Setup
CM-03NLCH
Indication
Door Station
Module
PS-5E
Network
Switch
Note£1.BUS(1-8)wire include:¢3-core data wire£
¢8-core audio wire(4 route ways); ¢4-video wires:75-5
2.Wall phone/management unit wiring£
¢3-core data wire£¢2-core audio wire£¢1 video wire
3.We recommend you use shield wire for general wire,
or the interfere will affect the sustem normal
specification.
's
2.
(1)Network v diagram£
Network system diagram
ideo system
+DC-
¡AC¡
TRANSFORMER
Model£PS-5E
Input£230V¡50Hz
Output£18V 800mA
Notes:Usedin indoor
+DC-
¡AC¡
TRANSFORMER
Model£PS-5E
Input£230V¡50Hz
Output£18V 800mA
Notes:Usedin indoor
PS-5E
PS-5E
+DC-
¡AC¡
TRANSFORMER
Model£PS-5E
Input£230V¡50Hz
Output£18V 800mA
Notes:Usedin indoor
+DC-
¡AC¡
TRANSFORMER
Model£PS-5E
Input£230V¡50Hz
Output£18V 800mA
Notes:Usedin indoor
PS-5E
PS-5E
+DC-
¡AC¡
TRANSFORMER
Model£PS-5E
Input£230V¡50Hz
Output£18V 800mA
Notes:Usedin indoor
+DC-
¡AC¡
TRANSFORMER
Model£PS-5E
Input£230V¡50Hz
Output£18V 800mA
Notes:Usedin indoor
Conformity Unit
¢Wiring between switch and conformity unit (BUS board):
(5)Wiring between conformity unit's PORT board and management unit:
LA
Data A
LB
Data B
COM
Common
terminal
AF+ AF- TV+ TV-
OR BK BL GR YL
Audio Audio GND Video Video GND
Management unit's
video port
2.Audio system:
¢Wiring among network switches:
LA
Data A
LB
Data B
COM
Common
terminal
AI1+
Audio input
for No.1
route way
AI1- VI1+ VI1-
Network
Switch
LA LB COM AO1+ AO1- VO1+ VO1-
Network
Switch
Audio GND
input for No.1
route way
Video input
for No.1
route way
Video GND
input for No.1
route way
Data A Data B
Common
terminal
Audio output
for No.1
route way
Audio GND
output for
No.1 route way
Video output
for No.1
route way
Video GND
output for No.1
route way
LA
Data A
LB
Data B
COM
Common
terminal
AI1+
Audio input
for No.1
route way
AI1- VI1+ VI1-
Network
Switch
LA LB COM AF1+ AF1- TV1+ TV1-
Conformity
unit s BUS
board
'
Audio GND
input for No.1
route way
Video input
for No.1
route way
Video GND
input for No.1
route way
Data A Data B
Common
terminal
Audio for
No.1 route
way
Audio GND
for No.1
route way
Video for
No.1 route
way
Video GND
for No.1
route way
Conformity
unit s port
board
'
Management
unit
box
'switch
Data A Data B Common
terminal Audio Audio GND
(1)
£
Wiring between door
station and module
POWER
Audio
power
AF
Audio
DATA
Data
AGND
VCC AF DATA GND
Door
Station
Module
Audio Data
Audio
power
Audio
GND
Audio
GND
(2)
£
Wiring between module and
WL-02NLFL indoor phone
VCC
Audio
power
GND
Audio
GND
T&R G1-G4
+12V GND T&R AGND
Module
Indoor
phone
Audio
GND
Audio
power
Audio
cortrol GND
Audio
Audio Audio
cortrol GND
12V
Power

37 14
4
BUS1 BUS1
BUS1
PS-5E Power
2
5
Electrical Lock
2
PS-5E Power
2
WL-03NHMC
Mangement Unit
BUS8
4
PS-9 Power
2
2
WL-02NLFH
222
WL-02NLFD
4
4
4
WL-03NWD(A) Wall Phone
Network
Switch
Module
2
PS-2E Power
5
Setup In dicat ion
WL- 03N LCH
Setup In dicat ion
WL- 03N LCH
2
PS-2E Power
Door Station
WL-03NQH2-162
NETWORK SWITCH
GND AF DATA
LA LBAI1+ AI1-
POWERGND AF DATA
COMAO1+AO1- AI2+ AI2-AO2+AO2-
POWERGND AF DATA
WL-03NQH
NETWORK SWITCH
Network
Switch
+10%
-15%
PS-9 POWER SUPPLY
AC input:230V
A?.5/V? 2
6V/0.5A
DC output£
Protection Grade:IP30
Note£1.BUS(1-8)wire include:¢3-core data wire£
¢8-core audio wire(4 channels);
2.Wall phone/management unit wiring£
¢3-core data wire£¢2-core audio wire£
3.We recommend you use shield wire for
general wire, or the interfere will affect the
sustem normal specification.'s
(2)Network audio system diagram£
¡AC¡
+DC-
TRANSFORMER
Model£PS-5E
Input£230V¡50Hz
Output£18V 800mA
Notes:Usedin indoor
¡AC¡
+DC-
TRANSFORMER
Model£PS-5E
Input£230V¡50Hz
Output£18V 800mA
Notes:Usedin indoor
¡AC¡
+DC-
TRANSFORMER
Model£PS-2E
Input£230V 50¡60Hz
Output£13.5V 800mA
Notes:Usedin indoor
¡AC¡¡AC¡
+DC-
TRANSFORMER
Model£PS-2E
Input£230V 50¡60Hz
Output£13.5V 800mA
Notes:Usedin indoor
¡AC¡
4
2
WL-02NLFC
2
2
WL-02NLFL WL-02NLFH1
¢ndoor phone CM-02NLRV/CM-02NLRI/CM-02NLRJ£Wiring instruction from module to i
¢Video system-- Wiring from module to audio indoor phone£
(4)Wiring between switches and among switch, door station, and conformity unit:
¢Wiring between switch and door station, module:
POWER AF
Audio
DATA
Data
AGND MONI
Monitor
+18V TV- TV+
Video
POWER AF DATA GND MONI +18V TV- TV+
Door
Station
Network
Switch
Module
A+18V AFIN DATA AGND MONI V+18V VGND TVIN
¢Wiring between switch and extra door station:
Audio Monitor Audio
cortrol GND Video
T&R MONI AGND V+18V VGND TV
T&R MONI AGND V+18V VGND TV A+18V GND
Module
Video
Power
Video
GND
Audio
Power
Audio
GND
Audio Monitor Audio
cortrol GND Video
Video
Power
Video
GND
Indoor
Phone
Audio Monitor Audio
cortrol GND Video
T&R MONI AGND V+18V VGND TV
Two wires from indoor
phone, non polarity
Module
Video
Power
Video
GND
Indoor
Phone
1
(T&R)
Audio
Power
Audio
GND
Video
GND
Video
Power
Audio Data Monitor Video
Audio
Power
Audio
GND
Video
GND
Video
Power
Audio
Power Audio Data Monitor Video
Audio
GND
Video
GND
Video
Power
POWER AF
Audio
DATA
Data
AGND MONI
Monitor
+18V TV- TV+
Video
AF DATA GND +18V TV- TV+
Extra
Door
Station
Network
Switch
Audio
Power
Audio
GND
Video
GND
Video
Power
Audio Data Video
Audio
GND
Video
GND
Video
Power
EnptyEnpty
A+18V GND
Audio
Power
Audio
GND
2
(AGND) +12V GND
A+18V GND
Audio
Power
Audio
GND
For WL-02NLFL
Note:WL-02NLFL indoor phones have to use four-cord cables (T&R/AGND/V+12V
/GND) while the other indoor phones use two-cord cables(T&R/AGND).
12V
Power

15 36
MONITOR
CALL
UNLOCK
BUSY
POWER
NLRaM02-CM
Main indoor phone
Indicator
CM-03NLCH-162
Setup
A+18VAFOUT DATA AGND MONI V+18V VGND TVOUT T&R MONI AGND V+18V VGND TV A+18V GND T&R MONI AGNDV+18V VGND TV A+18V
A+18V AFIN DATA AGND MONI V+18V VGND TVIN T&R MONI AGNDV+18V VGND TV A+18V GND T&R MONI AGNDV+18V VGND TV A+18V
3.Diagram for main indoor phone CM-02NLRaM£
3+1
6+1
4+1
6+1
4+1
3
CM-02NLRbM
Extra Indoor Phone
WL-06NFbH
Extra Indoor Phone
CM-03NLCH-162 Module
CM-06-03NLd2
Front door station
Electrical Lock
2
6+1
Connect to door
station or switch
(Use 2 coaxial power wire to
connect with the extensions)
2
MONITOR
CALL
UNLOCK
BUSY
POWER
MONITOR
CALL
UNLOCK
BUSY
POWER
101
CM-02NLRbM
Extra Indoor Phone
2
POWER
Audio
power
GND LK- LK+
+
Power+
-
Power- Electrical
Lock
Door
Station
PS-5E
Power
Electrical
Lock
Electrical
Lock
(2)Wiring instruction from door station to module£
POWER
Audio
power
AF DATA GND MONI
Monitor
+18V TV- TV+
A+18V AFIN DATA AGND MONI V+18V VGND TVIN
(3)Wiring instruction from module to indoor phone£
Audio Monitor Audio
cortrol GND Video
T&R MONI AGND +18V VGND TV
T&R MONI AGND V+18V VGND TV A+18V GND
Empty
¢Wiring instruction from module to indoor phoneCM-02NLRG£
1 2 3 4 5¡6 7
¢ndoor phone CM-02NLRH/CM-02NLRM£Wiring instruction from module to i
Module
Door
Station
Audio Data Audio
GND
Video
power
Video
GND Video
Audio
power Monitor
Audio Data Audio
GND
Video
power
Video
GND Video
Module
Video
Power
Video
GND
Audio
Power
Audio
GND
Audio Monitor Audio
cortrol GND Video
Video
Power
Video
GND
Indoor
Phone
Audio Monitor Audio
cortrol GND Video
T&R MONI AGND V+18V VGND TV
T&R MONI AGND V+18V VGND TV A+18V GND
Empty
Module
Video
Power
Video
GND
Audio
Power
Audio
GND
Audio Monitor Audio
cortrol GND Video
Video
Power
Video
GND
Indoor
Phone
8 Wiring Instruction¡
?.Wiring Instruction for video system
(1)Wiring Instruction among door station, power and lock:
Audio GND
power
Electrical
Lock
Electrical
Lock
12V
Power

35 16
Door Station
Electrical
Lock
CM-02NLRG or
CM-02NLRG-C
1 2 3 4 5 6 7
AGND +18V VGND VGND TV MONI T&R
Indication
CM-03NLCH-162
Setup
A+18VAFOUT DATA AGND MONI V+18V VGND TVOUT T&R MONI AGND V+18V VGND TV A+18V GND
T&R
MONIAGND V+18V VGND TV A+18V
A+18V AFIN DATA AGND MONI V+18V VGND TVIN T&R MONIAGNDV+18V VGND TV A+18V GND T&R MONI AGNDV+18V VGND TV A+18V
TVIN
VGND V+18V MONI AGND DATA AFIN A+18V
TV VGND V+18V AGND MONI T&R
T&R
MONI
AGND
V+18V
VGND
TV
CM-02NLRH/CM-02NLRH-C
TV
VGND
V+18V
AGND
MONI
T&R
MONI AGND V+18V VGND TV
T&R
Indication
CM-03NLCH-162
Setup
A+18VAFOUT DATA AGND MONI V+18V VGND TVOUT T&R MONI AGND V+18V VGND TV A+18V GND
T&R
MONIAGND V+18V VGND TV A+18V
A+18V AFIN DATA AGND MONI V+18V VGND TVIN T&R MONIAGNDV+18V VGND TV A+18V GND T&R MONI AGNDV+18V VGND TV A+18V
TVIN
VGND V+18V MONI AGND DATA AFIN A+18V
MONI AGND V+18V VGND TV
T&R
A+18V GND
CM-02NLRV/CM-02NLRV-C
A+18V
T&R
MONI
GND
V+18V
VGND
AGND
TV
POWER
AF
DATA
GND
MONI
+18V
TV-
TV+
V+18V
VGND
PS-5E Power
7¡System Wiring
1.Non network wiring for video system:
+DC-
¡AC¡
TRANSFORMER
Model£PS-5E
Input£230V¡50Hz
Output£18V 800mA
Notes:Used in indoor
+ -
PS-5E Power
+DC-
¡AC¡
TRANSFORMER
Model£PS-5E
Input£230V¡50Hz
Output£18V 800mA
Notes:Usedin indoor
+-
(1)Video system-1(module CM-03NLCH-162)£
GND
LK-
POWER
POWER
LK+
AF
DATA
GND
MONI +18V
TV-
TV+
¢Wiring between module and indoor phone£
WL-02NLFD
G4
G3
G2
G1
T&R
WL-03NLCH Module
1#
2#
4#
WL-02NLFH
WL-02NLFL
WL-02NLFH1
3#
1 32
GND+12VAGND
4
T&R
VCC
GND
+12V
GND
AGND
T&R
12V
Power

17 34
T&R
MONI
AGND
V+18V
VGND
TV
Indication
CM-03NLCH-162
Setup
A+18VAFOUT DATA AGND MONI V+18V VGND TVOUT T&R MONI AGND V+18V VGND TV A+18V GND
T&R
MONIAGND V+18V VGND TV A+18V
A+18V AFIN DATA AGND MONI V+18V VGND TVIN T&R MONIAGNDV+18V VGND TV
A+18V
GND T&R MONI AGND V+18V VGND TV A+18V
TVIN
VGND V+18V MONI AGND DATA AFIN A+18V
TV VGND V+18V AGND MONI T&R
MONI AGND V+18V VGND TV
T&R
Indication
CM-03NLCH-162
Setup
A+18VAFOUT DATA AGND MONI V+18V VGND TVOUT T&R MONI AGND V+18V VGND TV A+18V GND
T&R
MONIAGND V+18V VGND TV A+18V
A+18V AFIN DATA AGND MONI V+18V VGND TVIN T&R MONIAGNDV+18V VGND TV A+18V GND T&R MONI AGNDV+18V VGND TV A+18V
TVIN
VGND V+18V MONI AGND DATA AFIN A+18V
MONI AGND V+18V VGND TV
T&R
T&R
MONI
AGND
V+18V
VGND
TV
CM-02NLRJ Indoor Phone
A+18V GND
1
A+18V 2
T&R 3
MONI 4
GND
5
V+18V 6
VGND 7
AGND 8
TV
T&R
MONI
GND
TV
AGND
VGND
A+18V
V+18V
A+18V GND
A+18V
GND
1
A+18V 2 T&R 3 MONI 4 GND
5 6
VGND
V+18V 7
AGND 8 TV
CM-02NLRI Indoor Phone
CM-02NLRM or
CM-02NLRM-C
Connect to
audio indoor
phone
Door Station With Card Reader
Electrical
Lock
PS-5E
Power
PS-5E Power
V+18V
VGND
T&R
AGND
(2)Video system-2(module CM-03NLCH-162)£
Connect with
door bell button
Only for
CM-02NLRM1
+DC-
¡AC¡
TRANSFORMER
Model£PS-5E
Input£230V¡50Hz
Output£18V 800mA
Notes:Used in indoor
+ -
+DC-
¡AC¡
TRANSFORMER
Model£PS-5E
Input£230V¡50Hz
Output£18V 800mA
Notes:Used in indoor
+ -
+AI1- +AI2- +AI3- +AI4- COMLB LA
+AO1- +AO2- +AO3- +AO4-
POWERGND AF DATA GNDAFDATA POWER
DATA AF GND
COM LB LA AI1+ AI1- AI2+ AI2- AI3+ AI3- AI4+ AI4-
+AI1- +AI2- +AI3- +AI4- COMLB LA
+AO1- +AO2- +AO3- +AO4-
POWERGND AF DATA GNDAFDATA POWER
DATA AF GND
COM
LB LA
POWER GND AF DATA
DATA AF GND POWER
GND
AF
DATA
Input terminal from conformtiy unit
WL-03NQH Network switch
WL-03NQH Network Switch
Note£
PS-2E Power
PS-2E
Power
Extra Door Station
Door Station
Electrical
Lock
Electrical
Lock
WL-03NLCH Module
G4
G3
G2
G1
T&R
VCC
GND
DATA
AF
b)Wiring among WL switch, WL module and door station:-03NQH -03NLCH
To Indoor Phone
+
¡AC¡
+DC-
TRANSFORMER
Model£PS-2E
Input£230V 50¡60Hz
Output£13.5V 800mA
Notes:Usedin indoor
¡AC¡
-
Wires between network switches :the audio
output(AO) of the first network switch are
connected with the corresponding audio
input(AI) of the next network switch. The
data wire COM¡LA¡LB should be connected accordingly.
GND
LK-
POWER
POWER
LK+
AF
DATA
GND
GND
LK-
POWER
POWER
LK+
AF
DATA
GND
POWER
AF
DATA
GND
AF
DATA
GND
POWER
GND
12V
Power
12V
Power
12V
Power
COM LB LA +18V GND LOCK+LOCK-
GND
LK-
POWER
POWER
LK+
AF
DATA
GND
MONI +18V
TV- TV+
POWER
AF
DATA
GND
MONI
+18V
TV-
TV+ LOCK-
LOCK+
GND
+18V
LK+
LK-
POWER
GND