GeoVision GV-MNVR1000 User manual

Quick Start Guide
Quick Start Guide
GV-Mobile NVR System
The Vision of Security
Thank you for purchasing GV-Mobile NVR System. This guide is designed to assist the new user in getting immediate results
from the GV-Mobile NVR System. For advanced information on how to use the GV-Mobile NVR System, please refer to
GV-Mobile NVR System User's Manual (GV-Desktop < Program button < User Manual). 2014/09
English
MBNVR-QG-A

© 2014GeoVision, Inc. All rights reserved.
Under the copyright laws, this manual may not be copied, in whole or in part,
without the written consent of GeoVision.
Every effort has been made to ensure that the information in this manual is
accurate. GeoVision, Inc. makes no expressed or implied warranty of any kind
and assumes no responsibility for errors or omissions. No liability is assumed
for incidental or consequential damages arising from the use of the information
or products contained herein. Features and specifications are subject to
change without notice.
GeoVision, Inc.
9F, No. 246, Sec. 1, Neihu Rd.,
Neihu District, Taipei, Taiwan
Tel: [phone]
Fax: [phone]
http://www.geovision.com.tw
Trademarks used in this manual: GeoVision, the GeoVision logo and GV
series products are trademarks of GeoVision, Inc. Windows and Windows XP
are registered trademarks of Microsoft Corporation.
September 2014

Contents
1. Introduction ..........................................................................................1
1.1 Packing List............................................................................................................... 1
1.2 Software License....................................................................................................... 2
1.3 Recommended Hard Disks ....................................................................................... 2
1.4 Options...................................................................................................................... 3
1.5 Overview ................................................................................................................... 4
1.5.1 Front View...................................................................................................... 4
1.5.2 Rear View ...................................................................................................... 6
2. Getting Started.......................................................................................8
2.1 Interface Connection................................................................................................. 8
2.2 Turning on and off the Power ...................................................................................10
2.3 Installing the Storage Drive ......................................................................................13
2.3.1 GV-MNVR1000 System.................................................................................13
2.3.2 GV-MNVR2100 System.................................................................................14
2.4 Formatting the Storage Drive ...................................................................................15
2.5 Configure the IP Address .........................................................................................18
2.6 Exiting to Windows ...................................................................................................21
3. Accessing GV-Mobile NVR System ........................................................... 22
3.1 Main Screen .............................................................................................................22
3.1 1 Adding a Storage Drive to the Recording Path ..............................................23
3.1.2 Adding IP Cameras .......................................................................................24
3.1.3 Renaming the Camera ..................................................................................26
3.1.4 Choosing Recording Mode............................................................................26
3.2 Setting up a Recording Schedule .............................................................................27
3.3 Playing Back Video...................................................................................................28
3.3.1 Playback Controls .........................................................................................29
3.4 Backing Up Video Files ............................................................................................29
3.4.1 Playing Backup Files.....................................................................................31
4. System Restoration .............................................................................. 32

1. Introduction
Welcome to the GV-Mobile NVR System Quick Start Guide. In this quick guide, you will find
information on the basic installation and configurations of the GV-Mobile NVR System. For
detailed information, see GV-Mobile NVR System User’s Manual (GV-Desktop < Program
button < User Manual).
1.1 Packing List
1. GV-Mobile NVR System
2. 3-pin Terminal Block (for ACC Connection and DC In)
3. HDD screw x 4 (for GV-MNVR1000 System)
4. HDD screw x 8 (for GV-MNVR2100 System)
5. GPS Antenna
6. GV-NVR Dongle for third-party IP Camera Connection (Optional)
7. DVD (User’s Manual and Quick Start Guide included)
1

1.2 Software License
Free License 24 / 32 channels from GV-IP Devices
Maximum License 24 / 32 channels from third-party IP devices
Increment for Each
License 1 to 24 / 32 third-party IP cameras at an increment of 2
Optional
Combination N/A
Dongle Type External
1.3 Recommended Hard Disks
GV-Mobile NVR supports up to 2 SATA HDD / SSD (2.5”) with up to 2 TB capacities. For the
optimal system performance, it is recommended to use the SSD (MLC or SLC) or the
enterprise-level HDD, such as HGST Endurastar series and Toshiba automotive HDD.
2

1.4 Options
Optional devices can expand your GV-Mobile NVR System’s capabilities and versatility.
Contact your dealer for more information.
GV-IO Box (4 Ports)
GV-IO Box 4 provides 4 inputs and 4 relay outputs, and supports
both DC and AC output voltages. A USB port is provided for PC
connection.
GV-IO Box (8 Ports)
GV-IO Box 8 provides 8 inputs and 8 relay outputs, and supports
both DC and AC output voltages. A USB port is provided for PC
connection.
GV-IO Box (16 Ports)
GV-IO Box 16 provides 16 inputs and 16 relay outputs, and
supports both DC and AC output voltages. A USB port is provided
for PC connection.
GV-Joystick V2
GV-Joystick V2 facilitates the PTZ camera control. It can be
either plugged into the GV-Mobile NVR System for independent
use or connected to GV-Keyboard V3 to empower the operation.
GV-Keyboard V3
The GV-Keyboard V3 is designed to program and operate the
system, and it can also be connected with PTZ cameras directly
for PTZ control.
GV-IR Remote
Control
Controls GV-Mobile NVR System with the Remote Control.
GV-TouchDisplay133
The GV-TouchDisplay133 is a touch panel designed for
GV-Mobile NVR System. With the touch panel, you can monitor
live images and operate its OSD functions.
Power Adapter Power adapters are available in 4 regions: U.S.A., Australia, U.K
and Europe.
3G / 4G Module
The 3G or 4G module allows data exchange for the GV-Mobile
NVR through the network connection covering wide area. It also
empowers the application of GPS for the data transmission to the
GV-GIS for real-time vehicle tracking.
WiFi Module The WiFi module allows data exchange for the GV-Mobile NVR
through wireless network connection within local area.
Note: The WiFi / 3G / 4G module will be built in the GV-Mobile NVR System and tested before
shipment. Opening the case and installing the accessories yourself will void the warranty.
3

1.5 Overview
1.5.1 Front View
GV-MNVR1000 System
145 7 68 9
1011
12
11 11
1311
3
2
GV-MNVR2100 System
1564 7 8 9
11
10
11
10
11 14
1213
3
2
4

No. Name No. Name
1 Event Button (Not Functional) 8 Audio Line Out Port
2 HDD Status LED 9 Audio Microphone In Port
3 WWAN LED 10 2.5” HDD/SSD Slot
4 USB 3.0 Port 11 Antenna Port
5 Reset Button 12 WLAN LED
6 SIM Card Slot 13 Power Status LED
7 CFast Card Slot 14 USB 2.0 Port
Note: The WLAN WiFi and WWAN 3G / 4G module is optional.
Status Indicator LEDs
WWAN LED
WLAN LED
HDD LED
Power LED
Indicator LED Color Description
HDD LED Orange Glows when HDD/SSD is active.
WWAN LED Orange Glows when WWAN is active.
WLAN LED Orange Glows when WLAN is active.
Power LED Green Glows when power is turned on.
5

1.5.2 Rear View
GV-MNVR1000 System
13 6
47 8
10
1112
25
9
No. Name No. Name
1 Audio Microphone In Port 7 DC Power Output (Not Functional)
2 Gigabit Ethernet Port x 2 8 DC 10 V - 35 V Power Input
3 VGA Output 9 GPS Antenna Port
4 USB 2.0 Port x 2 10 MCU DIO Port (Not Functional)
5 GPIO Terminal Block (Not Functional) 11 COM Port x 3
6 DisplayPort Output 12 Audio Line Out Port
6

GV-MNVR2100 System
1456 7 8 9
10
10
10
12
15 12
13
3
2
11
12 14
No. Name No. Name
1 Gigabit Ethernet Port x 2 9 DC 10 V - 35 V Power Input
2 Audio Microphone In Port 10 Antenna Port x 3
3 USB 3.0 Port 11 MCU DIO Port (Not Functional)
4 DisplayPort Output 12 COM Port x 3
5 VGA Output 13 USB 2.0 Port
6 GPIO Terminal Block (Not Functional) 14 GPS Antenna Port
7 DC Power Output (Not Functional) 15 Audio Line Out Port
8 Fuse (15A)
7

2. Getting Started
2.1 Interface Connection
This section describes the equipments required to operate the GV-Mobile NVR System. Here
we use the GV-MNVR2100 System for example.
3
Rear Side
4
2
1
HDD/SSD x 2
Front Side
7
5
6
1. There are two options for connecting the power.
8
A. Connect the GV-Mobile NVR System to the vehicle’s power battery and ACC wire
using the supplied 3-pin terminal block. The system will automatically start after you
turn on the vehicle ignition. Power is supplied to the system as long as the vehicle
ignition is on.
Ground Ignition
Power

B. Optionally purchase a power adapter from GeoVision. See 2.2 Turning on and off
the Power.
2. Use the VGA cable or the DisplayPort cable to connect the unit to the monitor.
Note: The GV-Mobile NVR System supports dual-monitor display. You can connect two
monitors by using the VGA connector and DisplayPort.
3. Connect one end to the Gigabit Ethernet port and the other end to Network by using the
RJ-45 cable.
4. Connect the keyboard and the mouse to the USB ports.
5. Connect the speaker to the Audio Line Out port.
6. Optionally connect the microphone to the Audio Microphone In port for two-way audio with
IP cameras.
7. Insert the 2.5” HDDs or SSDs into the storage slots. For details, see 2.3 Installing the
Storage Drive.
After the unit is powered on, the Power Indicator LED shows constant green.
Before recording, you need to format the storage drive and add it to the recording path of the
system. For formatting the storage drive, see 2.4 Formatting the Storage Drive. For adding the
storage drive to the recording path, see 3.1.1 Adding the Storage Drive to the Recording Path.
9

2.2 Turning on and off the Power
The GV-Mobile NVR System is designed to connect to the vehicle’s ACC wire. However, you
can optionally purchase a power adapter (AC 100 ~ 240 V) from GeoVision for power
connection.
2.2.1 Connecting to the ACC Wire
To turn on the GV-Mobile NVR System, connect the vehicle’s ACC and power wires to the
unit’s power input using the supplied 3-pin terminal block. The system will automatically start
after you power on the vehicle for 5 seconds.
After you power off the vehicle for 3 seconds, the system will turn off automatically.
2.2.2 Using the Power Adapter
To turn on and off the GV-Mobile NVR System using an optional power adapter from
GeoVision, follow the steps below.
1. Plug the 3-pin terminal block connected with power adapter to the panel’s power pins. The
GV-Mobile NVR System will be powered on about 5 seconds later.
2. To turn off the GV-Mobile NVR System, shut down the system through the Windows
desktop.
10

Using Rocker Switch to Simulate ACC Ignition
For quick control of turning on or off the GV-Mobile NVR System, you can install a rocker
switch to the 3-pin terminal block with the optional power adapter. For the connection and
operation, follow the steps below.
Rocker
Switch
1. For the 3-pin terminal block with optional power adapter, unplug the U-shaped wire from
the Power and Ignition pins.
U-Shaped
Wire
Power
IgnitionGround
2. Connect the wires of the rocker switch to the Power and Ignition pins respectively.
3. Plug the terminal block the panel’s power pins.to
11

4. Press the rocker switch to turn on the GV-Mobile NVR System without operating on the
Windows desktop. Once the rocker switch is on, the GV-Mobile NVR System will be
powered on about 3 seconds later.
5. To turn off the GV-Mobile NVR System, press the rocker switch again.
Note: After the power is on, the GV-Mobile NVR System will run a series of self-tests, and a
series of messages may be displayed as the various hardware and software subsystems are
activated. After the process is finished, the GV-System Software (Multicam Surveillance
System) should load automatically and bring you to the main screen.
12

2.3 Installing the Storage Drive
The GV-Mobile NVR System uses SATA hard drive / SSD for video data storage. Before
recording, be sure to install the storage drive.
.3.1 GV-MNVR1000 System 2
1. Loosen the thumb screws on the HDD/SSD slot and pull out the drive drawer.
2. Insert the storage drive into the drive drawer with the SATA data and power connector
facing towards the end.
Power
Connector
3. Secure the storage drive with the drive drawer using the supplied 4 screws.
Note: For convenience, it is suggested to secure the screws with the drive drawer being
placed downward.
4. Insert the drive drawer into the HDD/SSD slot and secure the thumb screws.
13

2.3.2 GV-MNVR2100 System
1. Loosen the thumb screws on the HDD/SSD slots and remove the covers.
2. Press the release latch and pull out the drive drawer using the drawer handle that pops
out.
Release Latch
3. Insert the storage drive into the drive drawer with the SATA data and power connector
facing towards the end.
Power
Connector
4. Secure the storage drive with the drive drawer using the supplied 4 screws.
5. Insert the drive drawer into the HDD/SSD slot, put the drawer handle back and rotate the
release latch until it is vertical to lock t e drive drawer.h
6
14
. Put the cover back and secure the thumb screw.
7. Repeat the steps above to install the storage drive in the other HDD/SSD slot.
The HDD Status LED glows, and the storage drive is ready for use.

2.4 Formatting the Storage Drive
ive before
recording.
1. On the GV-Desktop, click the Programs button, and select Disk Management.
2. Type the ID and password in the dialog box. The default ID and password are “0000”.
After installing HDD / SSD to your system, you will need to format the storage dr
3. Right-click in the unallocated space of a new drive, and select New Simple Volume.
15
4. In the appeared New Simple Volume Wizard dialog box, click Next to continue.

5. The default partition size is the same as the maxim
necessary and click Next to continue.
um disk space. Make changes if
6. Assign a drive path that is not in use by other devices and click Next to continue.
16

7. Type a name in the Volume label box, ex. HDD1, and click Next to continue.
8. When the formatting is complete, click Finish to close the wizard.
17