GERA Z LED 60 Instruction sheet

Operating instructions Starterset Z LED 60 Set Status 19.01.2021
(TNR: 33700066 / 33700067) GERA Leuchten GmbH
Instructions for commissioning and operating
the adjustable LED lights
When delivered, the radio remote control and the supplied control unit are already connected to
each other. The teaching of further control units is described under point 3.
1. Radio remote control
2. Preparation of the radio remote control
(1) Unpack the radio remote control
(2) Open the cover on the back of the radio remote control and remove the insulation strip from
the battery compartment. Then close the lid again.
(3) Attach the magnetic holder to the desired location using the double-sided adhesive tape
supplied. Alternatively, the two screws can also be used.
brighter
cold white
Zone buttons
1-6
On / Off button
warm white
Zone buttons 1-6
converter
Control unit
Max. 60 Watts
Max. 36 Watts
Teach button
Power cord
9-way distributor
Insulation strips
Radio remote control
cover
Lock remote control:
Press the brightness and
zone buttons simultaneously
for 5 seconds.
After that, only the on / off
function is active.
Lock remote control:
cw and zone buttons press
simultaneously for 5 seconds.

Operating instructions Starterset Z LED 60 Set Status 19.01.2021
(TNR: 33700066 / 33700067) GERA Leuchten GmbH
3. Teach the control unit to the radio remote control
You can teach in an infinite number of control units per zone button .
We recommend first teaching in all control units to zone key 1.
Then the control units can be taught-in again individually for the remaining zones, as explained
under point 4.
3.1 VARIANT 1 –teach-in button on the control unit
(1) Carry out a RESET.
Press the teach-in button for longer than 3 seconds or until the connected light source
flashes briefly to indicate that the reset was successful.
(2) You can then prepare the control unit for teaching by briefly pressing the teach-in button .
(3) Immediately afterwards, press one of the six zone buttons for approx. 3 seconds.
(4) Check FUNCTION. Long press on the zone button of the radio remote control to switch
the respective zone on / off.
Repeat the process to teach in additional devices.
3.2 VARIANT 2 –Voltage interruption to the control unit
If the control unit is inaccessible, do the following:
(1) The voltage supply to the control unit must be briefly interrupted in order to signal to the
control unit that a learning process is taking place. The interruption can be done by pulling
the power plug or by a switch (house installation).
(2) Then restore the voltage (plug in the mains plug or switch on the switch).
Immediately afterwards, press one of the six zone buttons twice quickly (like a double-
click) and then once long for approx. 3 seconds. This sequence must take place immediately
one after the other.
(3) Check FUNCTION. Long press on the zone button of the radio remote control to switch
the respective zone on / off.
Repeat the process to teach in additional devices.
IMPORTANT! After each teach-in process, you should wait 60 seconds before teaching in further devices.
If there is no connection between the radio remote control and the control unit, repeat steps 3.2.1 - 3.2.2
You can repeat this step as often as you like.
If there is no connection between the radio remote control and the control unit, repeat steps 3.1.1 - 3.1.3
You can repeat this step as often as you like.
IMPORTANT! The learning process is limited in time. The teach-in process must be restarted after 5 seconds.
IMPORTANT! The learning process is limited in time. The teach-in process must be restarted after 5 seconds.

Operating instructions Starterset Z LED 60 Set Status 19.01.2021
(TNR: 33700066 / 33700067) GERA Leuchten GmbH
4. Teach in several control units
(1) Example: Teaching three control units to three different zone buttons .
The advantage of this method is that each control unit can be controlled individually.
In this way, the light color and the brightness can be set differently for each control unit
in the later step.
Zone 1 Zone 2 Zone 3
(2) Example: teaching several control units to one zone key .
With this method the light color as well as the brightness can be controlled synchronously
with several control units..
Zone 1 Zone 1 Zone 1
5. Operation
Briefly pressing the on / off button switches all zones on or off at once.
Briefly press the zone button on the radio remote control to select the respective zone which
is to be operated. Several zones can be selected one after the other in order to operate them
simultaneously (synchronously).
Long press on the zone button of the radio remote control to switch the respective zone
on / off.
You can select the desired emotion setting by pressing the buttons on the radio
remote control. You can change the settings by briefly pressing a button. You can also press and
hold the button for a quick change.
IMPORTANT! After each teaching process, you should wait 60 seconds before teaching in further devices.

Operating instructions Starterset Z LED 60 Set Status 19.01.2021
(TNR: 33700066 / 33700067) GERA Leuchten GmbH
6. Overview of errors / causes
Disorder
Possible Cause
remedy
Light source does not react to the
radio remote control
The radio remote control is not yet
connected to the control unit
Teaching the radio remote control to
the control unit.
Variant 1 or variant 2
Radio remote control battery empty
Replace the battery
Power failure in the kitchen
Restore mains voltage. The radio
remote control settings are saved.
Teaching the radio remote control
to the control unit.
Variant 1 or variant 2
Radio remote control defective
If all other possible causes are
excluded, please contact the furniture
store
A light source flashes continuously
The radio remote control lost the
connection during teaching
Teaching the radio remote control to
the control unit.
Variant 1 or variant 2
All light sources flash
Short circuit
Check cables and connectors and
eliminate short circuit
The LEDs of a light source are
weaker than the other
comparable light sources
Possibly too many lights are connected
to a control unit
Max. 36 watts can be connected to
one slot or max. 60 watts, depending
on the control unit. The lights should
be distributed over the multiple slots.
Defective lamp
If all other possible causes are
excluded, please contact the furniture
store
One light source is cool white,
while all others are warm white
The light source concerned was
delivered retrospectively and comes
from a subsequent delivery that has
since been converted
A reverse polarity cable (article YVLK)
must be requested. By plugging this
reverse polarity cable between the light
source and the control unit, the light
source is polarized correctly again.
The light source was polarized
incorrectly
One of more than one light source
is not working.
Plug connection loose
Insert plug connections between light
source and distributor on the control
unit.
Check cable break, whether it has
been severely kinked in one place or
otherwise interrupted
If so, please contact the furniture store
Defective light source
If all other possible causes are
excluded, please contact the furniture
store
Remote control does not respond,
except on / off function.
Remote control is locked.
Unlock remote control:
cw and zone buttons at the same time
Press for 5 seconds.

Operating instructions Starterset Z LED 60 Set Status 19.01.2021
(TNR: 33700066 / 33700067) GERA Leuchten GmbH
7. Connecting the control unit to a Zigbee hub (smart home)
Note:
This function can only be carried out if the devices have previously been reset to the
factory settings. The remote control can then be reconnected to the control unit if it
should continue to be used.
(1) Reset the control unit to the factory settings.
Press the learning button on the control unit 5 times in quick succession, or switch
the device off and on again 5 times in quick succession (switching the mains voltage
of the converter 230 V).
Note:
- If the device has already been reset, it will not respond when you reset it again.
- All affiliations to networks and settings are deleted.
(2) Put the Zigbee Hub in search mode. To do this, follow the instructions for the corresponding
device or APP.
(3) Switch the control unit off for 3 seconds (switch on the 230 V mains voltage of the
converter) and then on again, the lighting flashes slowly twice.
Search mode lasts for 15 seconds. If the connection failed, try put the device in
search mode again.
(4) The connected lighting unit flashes 5 times and then lights up continuously. Now
the device appears in the user interface (APP) of the Zigbee Hub.

Operating instructions Starterset Z LED 60 Set Status 19.01.2021
(TNR: 33700066 / 33700067) GERA Leuchten GmbH
8. Fault / cause overview for connecting the control unit to a Zigbee hub (smart home)
Disorder
Possible Cause
remedy
The Zigbee device is not
recognized
Power supply interrupted
Make sure that the power supply is
guaranteed.
The lights should be on.
No connection to the WiFi
Check the WiFi connection from your
smartphone or tablet.
No Zigbee hub available
A so-called Zigbee hub is required to
control the Zigbee lights. This can either
be already integrated in your smart
home system, or an external Zigbee
hub (e.g. Philips Hue Bridge) must be
installed.
Zigbee Hub is not connected to the
home network
Ensure the connection to the home
network. This should also be displayed
in the APP used.
Software out of date
Check whether new updates are
available for your smart home system,
the Zigbee Hub, or the APPs used and
install them.
Smart home system is not compatible
Check whether the Zigbee smart home
system is compatible. Additional
hardware or software may have to be
installed.
Control unit is already connected to a
remote control
Reset the device to factory settings
(see point 7.1)
After that, you can connect it to the
remote control again.