Gerreka HIPPO Operating instructions

5
HIPPO
Quick installation and programming guide English
IMPORTANT
NOTE
This quick guide is a summary of the complete installation guide. The guide contains safety warnings and other
explanations that must be taken into account. The most recent versions of this guide and the installation
manual are available in the "Downloads" section on Erreka's website.
http://www.erreka-automation.com
E310B
Full installation elements
ELECTRICAL WIRING:
Element No. wires per section Maximum length
A: Main power supply 5x1.5mm230m
B: Flashing light 2x0.5 mm230m
C: Photocells (Tx/Rx) 2x0.5 mm2/ 4x0.5mm230m
D: Key switch 2x0.5 mm225m
E: Operator
(motor + limit switch + microswitch STP) 4x1.5mm2+3x0.5mm2+2x0.5mm220m
F: Antenna Coaxial cable 50k(RG-58/U) 5m
MSM-050/00 – 2019-01-11

6
1
1
D310A
1
2
3
4
STP
D310B
1
2
3
STP
Unlocking and locking
Unlocking (manual operation)
1Turn the key (1) and remove the cover (2).
2Insert the hexagonal key (3) supplied in the socket (4).
3Turn the key (3) clockwise to unlock.
The gate can now be moved manually.
Locking (motorised operation)
1Turn the key (3) anti-clockwise to lock.
2Remove the key (3).
3Place the cover (2) and lock with the key (1).
4Move the gate manually to interlock the motor.
STP: STOP microswitch; opens when the cover is removed (2). Must be connected to the STOP cable connectors
on the control board. This prevents the motor from moving with the cover (2) removed.
M310A
225mm
38mm
365mm
138mm
223mm
665mm
C310A
Dimensions (mm) and assembly positions

7
P310A P310B
P310F
2-3mm
P310E
P310G
P310D
P310H
L
P310I
L
P310J
1 Fold the stringers properly, as
shown in the diagram.
Assembly
2 Fasten the stringers on the base
plate temporarily, without fully
tightening the nuts, as they must
be removed later.
4 With the concrete set, remove
the nuts and assemble the
motor-reducer on the base plate,
using these nuts, without fully
tightening them yet.
5 Fasten the rack to the gate
provisionally (see instructions).
Unlock the operator and adjust
its position if necessary.
7 After checking the rack-and-
pinion adjustment, fasten the
rack permanently.
Tighten the fastening nuts of the
motor-reducer firmly on the base
plate and assemble the housing.
3 Dig a well to the correct size and
position the duct for the cables
and the base plate with the
stringers.
Make sure the base plate is level
and pour in the concrete.
6 With the operator unlocked,
move the leaf manually along the
whole open/close path to check
that the rack moves correctly
with the pinion.
There should be a slight gap
(approximately 2-3mm) between
the teeth of the pinion and the
rack.
8 Using their corresponding set screws, adjust the opening and closing limit
switch cams (L) on the ends of the rack.
Take into account that after activating the limit switches, the gate will
move another 2-3 cm, therefore, it is advisable to fit the limit switch cams
(L) leaving an appropriate gap as regards the gate's mechanical stops.

8
Z2/W2
Z1/W1
U2 V2
U1 V1
U(R) V(S) W(T)
Z2/W2
Z1/W1
U2 V2
U1 V1
U(R) V(S) W(T)
FC1 FC2
1
2
3
PWR
123
1
2
31
2
31
2
3
*
1
2
3
FCC FCA
1
2
3
FCA FCC
FC1
FC2
STP
P310Z
STP
M
VIVO-T101
HIPPO operator parts:
FC1 movement 1 limit switch
FC2 movement 2 limit switch
*electric bridge
STP STOP microswitch (normally closed, opens as
gate is removed)
Mthree-phase motor
VIVO-T101 control board parts:
PUL1 close mini-pushbutton
PUL2 open mini-pushbutton
SW1 Main switch
PWR Electric supply
A1 operator connections:
1FCA1 cable connector limit switch
2limit switches common
3FCC1 cable connector limit switch
U, V, W motor power supply
PE earth
STOP STOP cable connectors
Electrical connections with VIVO-T101
Checking turning direction and limit switches: Press PUL1 (close) and PUL2 (open) to check the turning direction
of the operator. If it is not correct, interchange connections V and W.
The connection of the operator to a VIVO-T101 control panel is shown as an example.
The operator must be connected to the control panel as shown in the attached diagram. To connect the
rest of the elements of the installation, consult your control panel instructions.
Before carrying out any gate movement, ensure there are no persons or objects in the radius of action of
the gate and the drive mechanisms.
Complete the installation in line with low voltage regulations and applicable standards.
Use cables with sufficient section, always earthed.
Check the manufacturer's instructions for all the elements installed.