GhostBed Foundation TWIN XL User manual

Center Frame
The top can be idenfied
by the flat top that travels
the length of the frame.
Twin and Twin Long
foundaons do not use
center frames.
Please Note:
· The Foundaon is to be assembled on a hard flat surface
· It is recommended that two people are available for assembly
· Wood is a natural product. If there are visual discoloraons, knots
· or even minor cracks this will not adversely affect the foundaon
· use or durability.
Phillips screw driver is required for assembly
Connue with step 2 on the other side of this sheet.
60 - Wood Screws for Slats and Top &
Boom Rails (includes 4 extra screws)
Supplied Hardware
Please visit WWW.GhostBed.com for product
informaon and video instrucons.
>Limited 3 year warranty visit
WWW.GhostBed.com to view
and register warranty
>Compliant with CPSC FR1633
· Be aware of rough or sharp edges, use care during assembly
· Please follow steps in order for best results
Fabric Cover
Screws
Le Side Frame
The top can be idenfied by the 1
inch wide rib.
The outside can be idenfied by
the rounded corner.
The top can be idenfied by the 1
inch wide rib.
The outside can be idenfied by
the rounded corner.
Top Slat Bundle (2 sets)
Each set contains 1 top cross
rail and 6 top slats. The top
cross rail and slats are evenly
spaced and connected with
fabric strips.
Boom Cross Rails
Right Side Frame
1. Idenfy components.
GhostBed • 7143 West Broward Blvd
Plantaon, FL 33317 • 855-855-4499
Knock Down Maress Foundaon (Boxspring)
Assembly Instrucons
(KD-Foundaon®)
Made in USA

The top can be idenfied by the 1 inch wide rib.
The outside can be idenfied by the rounded corner. The top can be idenfied by the flat top
that travels the length of the frame.
Aligned & aached
3. Place the Center Frame between Le and Right Side Frames with the
flat full length side facing up. Please note that the
Twin and Twin Long
foundaons do not use a center support, so skip this step, if need be, and
connue with step 4.
2. Place the Le Side Frame and the Right Side Frame with the 1" wide
rib upward and to the outside.
4. Unroll one Slat Bundle. Note that the first slat (top cross rail) is longer
than the others. Aach one corner of the Top Cross Rail to one corner of
the Side Frame using two wood screws. Make sure the slat is flush all
around. Align other Side Frame and fasten using two wood screws. Align
Center Frame and fasten using one wood screws. Align and aach the six
Slats with three wood screws per slat at pre-drilled locaons. Make sure
the slat is flush all around and the fabric stching the slats is facing up.
Align other Side Frame and fasten using two wood screws.
6. Carefully turn the foundaon over so the Slats are flat on the floor.
Aach Boom Cross Rails to the corners of the Side and Center Frames
making sure they are flush all around. Aach boom cross rails using five
wood screws per rail.
5. Unroll remaining Slat Bundle. As was done with previous Slat Bundle,
aach Top Cross Rail to Frame ends using five wood screws. Make sure
the Top Cross Rail is flush all around. Align and aach the six Slats with
three wood screws per slat at pre-drilled locaons.
7. Once again, turn the complete foundaon over so the Slats are facing
upwards. Unfold the cover and pull it over and around the foundaon.
Ensure the corners are aligned ghtly and the enre foundaon is
covered.
Nature’s Sleep KD-Foundaon® Assembly Instrucons Made in USA