Gianni Industries ST-630E User manual

CopyrightAllRightsReserved. Page 1 of 5
P-MU-ST-630 Ver. A Publish: 2009.01.08
ST-630E Stand-Alone Access Control
Operation Manual
ⅠFeatures
zMaster Card and Codes
zAuto Reset Function
zSecurity System Setting/ Release
zSynchronize with Security System
zEntering/Exiting Programming Mode: Only Proximity
Codes + Proximity, Codes or Proximity
zDoor Status Monitor Function
zAnti Pass Back Function
zEmergent Access Alarm, Time Delay Alarm and Forced
Door Alarm output
zDual relays programmable On/Off or pulsed or latched mode
zLED Indicator to distinguish the status
zUse for all kinds of the electric lock.
Ⅱ. The Specifications:
Part No. ST-630E
Connection Connection/ Stand-alone
/Users 1000
/Record Volumes 1000
Reader Application WG26,WG34
Keys 12 Keys (0-9,*,#)
Interface RS485
Proximity Distance About 125 and 15 cm/13.56 for around 7 cm
Proximity
Frequency 125Khz (EM)
Indicators 3 LEDs
Dimension (mm) 114(L) x 69.5(W) x 10(D)mm
Operating Voltage: 12 VDC
Temperature -5 C-60 C
Humidity 5%-95%(Non-condensing)

CopyrightAllRightsReserved. Page 2 of 5
P-MU-ST-630 Ver. A Publish: 2009.01.08
ⅢIndicators Status and Default Value
Beep & LED indication:
Mode Signal Status
Yellow(flashing
slowly) Power-on, stand-by
Green On Valid entry, door relay active
Normal
Red Warning, invalid card or code, tamper, alarm relay
active
Yellow(flashing
Quickly) Enter Programming Mode.
LED
Programming Red flashing
Quickly) Card read, or clear the memory
1 Beep Invalid card、keypress、entry program mode
Normal 2 Beep Invalid cards, Mistake Codes
1 Beep Valid Entry, exit the Program Mode.
Beep
Programming 2 Beep Input mistake or other failure operation
Factory Default Setting:
Access Mode Card only (0000)
Card Memory All Bits
Transaction Memory（MAX 1000 cards）0 pcs
Master codes (Master Password) *123456#
(All) Functions of Alarm Clear the function (00)
Door Relay Time 5 Seconds
Key Timeout 5 Seconds
Awaiting code timeout 5 Seconds
Programming mode timeout 25 Seconds

CopyrightAllRightsReserved. Page 3 of 5
P-MU-ST-630 Ver. A Publish: 2009.01.08
ⅣOperation Instruction:
*xxxxxx# Enter Program Mode，Enter 6-digital Codes，(Default 123456)
* # Exit Program Mode
01*xxxxxx xxxxxx # Change Default Password, Press twice new 6-digital Codes
02*xxxx # Controller Station Setting［001-254］
05*xxx# Access only with the password, 0000-Unavaliable (Default, 0000)
Adding or Revised the Cards No.10*xxxx*XXXXXXXXXX #
Slot Position =00001~01000 and enter the 10 digital Cards No.
Adding the batch series Cards No.. XXXX=the beginning position
*XXXXX=the quantities of the batch series card No.
12*XXXX*XXXXX#
(The access mode is for Card Only) (ps. x≦01000)
Modify the cards access parameter
xxxxx= The beginning slot position
XXXXX= the ending slot position From=00001~01000
N is 0= Access not allow，1=Card only，2=Cards or Code，
3=Card & Code，4= Clear card information
13*xxxxx*XXXXX*N #
(When modify the Mode to “Card or Code” or “ Card & Code”，the
default Code is 0000.
14*xxxxx*XXXX# Set the position of the Code; xxxxx=slot position XXXX=4-digital
Code (Position =00001~01000)
15*99# Clear all Cards (Not including Master Cards)
17*xxxxxxxxxx# When forget the Cards slot position，can clear the cards information
by enter Cards No..
21*xxx# Alarm Time Delay Setting xxx=000~255 Seconds
Dual relays programmable time delay xxx=000~250 Seconds
(External Relay for Security System)
22*xxx#
(000 Latched Operation) (Default is 15 Seconds)
Master Cards Setting x=(1 or 2). 2 Master Card available25*X#
In the normal status, proximity the Master cards to Program Mode.
26*xxxxx*XXXXX# Security Cards arrange Setting XXXXX=00001~01000 .The arrange
of the No. should be continuing which can’t skip the No.
x=0 General Setting Mode (Default x=0)30*x#
x=1 Card Only. Access the door by reading cards that no matter the
cards are set into the system or not.
32*x# Anti Pass Back Function
x=0/ OFF X=1/ ON
33*x# Two Doors Synchronize x=0 OFF X=1 ON，Access

CopyrightAllRightsReserved. Page 4 of 5
P-MU-ST-630 Ver. A Publish: 2009.01.08
Controller and Reader can open different doors.
34*99# Reset the function of Anti Pass Back.
35*x# (for connecting
controller)
x=1= access record to duty
x=0= access record Not to Duty
(x= default is 0)
x=0 Green LED is controlled by Controller x=1 Green LED is
controlled by external system
38*x#
(The second Relay contact to the Door Status and negatron (-) ，
Green LED flash can synchronize with Security System.
51*99# Reset to Default, and clean the controller memory to the factory
default
Add New Cards，read card once and 1 Beep heard for adding the
new card. Read card twice and 2 Beep heard to delete the cards.
55*99#
(After add Cards，the default access mode is “Card Only”)
70*X# ［For LCD series］X=0 Screen Backlight ON ，x=1 Screen Backlight Off automatically
Emergent Code Setting，Enter twice 6-Digital Code。
71*XXXXXX XXXXXX #
Enter the Code can link to the other relay to activate the external
system. 22*xxx # for setting the active time. (second)
72*xxx#
xxx=000~255 Seconds
Door Left OpenAlarm Time Delay - The door does not close after the
limited time, and the controller will output the alarm.
73*x # x=1 Enter the emergent code or press 99* with Security Cards, the
relay of the controller/ ON; X=0 OFF
74*x# X=1 Door Left Open Alarm and Force Open Mode are ON; X=0 OFF
76*x# X=1 Emergent Alarm /ON，x=0 OFF
When setting or Release the External Relay, Please enter the
codes99*and then read the security card.
99*
(Operating in the Normal Mode.)
Ⅴ、 Wiring diagram:

CopyrightAllRightsReserved. Page 5 of 5
P-MU-ST-630 Ver. A Publish: 2009.01.08