WoMaster WA512G Series User manual

C
COVER
WA512G Series
Industrial IEEE 802.11a/b/g/n/ac Wireless Mesh AP/Client
Nov.2020 V.1.3

2
WoMaster
WA512G
Industrial Dual Radio 2.4G+5GHz Concurrent Wireless Mesh AP/Client
User Manual
Copyright Notice
© WoMaster. All rights reserved.
About This Manual
This user manual is intended to guide a professional installer to install and to configure the WoMaster
Industrial Wireless MESH AP/Client. It includes procedures to assist you in avoiding unforeseen problems.
NOTE:
Only qualified and trained personnel should be involved with installation, inspection, and repairs of this
router.
Disclaimer
WoMaster reserves the right to make changes to this Manual or to the product hardware at any time without notice.
Information provided here is intended to be accurate and reliable. However, it might not cover all details and
variations in the equipment and does not claim to provide for every possible contingency met in the process of
installation, operation, or maintenance. Should further information be required or should particular problem arise
which are not covered sufficiently for the user’s purposes, the matter should be referred to WoMaster. Users must be
aware that updates and amendments will be made from time to time to add new information and/or correct possible
unintentional technical or typographical mistakes. It is the user’s responsibility to determine whether there have
been any such updates or amendments of the Manual. WoMaster assumes no responsibility for its use by the third
parties.
WoMaster Online Technical Services
At WoMaster, you can use the online service forms to request the support. The submitted forms are stored in server
for WoMaster team member to assign tasks and monitor the status of your service. Please feel free to write
to [e-mail] if you encounter any problems.

3
TABLE OF CONTENTS
COVER.................................................................................................................................................................................................1
TABLE OF CONTENTS .......................................................................................................................................................................3
DECLARATION OF CONFORMITY ...................................................................................................................................................6
SAFETY PRECAUTION.......................................................................................................................................................................8
1. INTRODUCTION......................................................................................................................................................................... 12
1.1 OVERVIEW................................................................................................................................................12
1.2 MAJOR FEATURES .......................................................................................................................................13
2. INSTALLATION............................................................................................................................................................................ 14
2.1 WA512G (IP67 HOUSING)..........................................................................................................................14
2.1.1 Dimension .............................................................................................................................................14
2.1.2 Product Appearance..............................................................................................................................14
2.2.3 Product Package ...................................................................................................................................15
2.2.4 Interface Installation.............................................................................................................................15
2.2.4.1 Wiring Power Input ............................................................................................................................16
2.2.4.2 Wiring Antenna..................................................................................................................................17
2.2.4.3 Wiring Waterproof Connector............................................................................................................18
2.2.5 Mounting the AP...................................................................................................................................19
2.2.6 LED........................................................................................................................................................20
2.2 WA512G-D (DIN-RAIL).............................................................................................................................21
2.2.1 Dimension .............................................................................................................................................21
2.2.2 Product Appearance..............................................................................................................................21
2.2.3 Product Package (WA512G-D)...............................................................................................................22
2.2.4 Interface Installation.............................................................................................................................22
2.2.4.1 Wiring Power Input ............................................................................................................................22
2.2.4.2 Wiring the Ground .............................................................................................................................23
2.2.5 Mounting the AP...................................................................................................................................23
2.2.5.1 DIN-Rail Mounting .............................................................................................................................23
2.2.5.2 WALL Mounting .................................................................................................................................24
2.2.6 ANTENNA & LED....................................................................................................................................26
3. WEB MANAGEMENT CONFIGURATION ................................................................................................................................ 27
3.1 SYSTEM....................................................................................................................................................29
3.1.1 Information...........................................................................................................................................29
3.1.2 Login Settings .......................................................................................................................................29
3.1.3 Network Settings ..................................................................................................................................32

4
3.1.4 Date and Time.......................................................................................................................................33
3.1.5 DHCP Server ..........................................................................................................................................34
3.2 ETHERNET PORT .........................................................................................................................................36
3.2.1 Port Status ............................................................................................................................................36
3.2.2 Ethernet Setting ....................................................................................................................................36
3.2.3 Traffic Control .......................................................................................................................................37
3.3 GPS........................................................................................................................................................37
3.3.1 GPS Status.............................................................................................................................................37
3.3.2 GPS Settings..........................................................................................................................................38
3.4 WIRELESS LAN ..........................................................................................................................................39
3.4.1 WLAN Status .........................................................................................................................................39
3.4.2 WLAN Settings ......................................................................................................................................40
3.4.2.1 AP mode.............................................................................................................................................40
3.4.2.2 Client mode ........................................................................................................................................45
3.4.2.3 WDS AP Mode ....................................................................................................................................48
3.4.2.4 WDS Client Mode ...............................................................................................................................51
3.4.2.5 Mesh Settings ....................................................................................................................................53
3.4.2.6 Client Router (Wireless WAN NAT) Mode ...........................................................................................56
3.4.3 WLAN Security ......................................................................................................................................57
3.4.4 Advanced ..............................................................................................................................................58
3.4.4.1 Roaming (Client based Fast Roaming)................................................................................................60
3.4.5 RADIUS Server (AP Mode) .....................................................................................................................63
3.4.6 Certificate File (Client Mode).................................................................................................................64
3.5 SECURITY..................................................................................................................................................65
3.5.1 Access Control .......................................................................................................................................65
3.5.2 Outbound Firewall ................................................................................................................................69
3.5.3 NAT Setting ...........................................................................................................................................73
3.5.4 OpenVPN ..............................................................................................................................................77
3.5.5 IPSEC Settings .......................................................................................................................................85
3.5.6 L2TP SETTING ........................................................................................................................................87
3.6 WARNING.................................................................................................................................................89
3.6.1 Ping Watchdog .....................................................................................................................................89
3.6.2 SYSLOG Settings ....................................................................................................................................90
3.7 DIAGNOSTICS.............................................................................................................................................91
3.7.1 Event Logs.............................................................................................................................................91
3.7.2 ARP Table..............................................................................................................................................91
3.7.3 Ping.......................................................................................................................................................93
3.7.4 Traceroute ............................................................................................................................................93
3.7.5 Network Statistics .................................................................................................................................94
3.7.6 Client Association List ...........................................................................................................................95

5
3.8 IOT.........................................................................................................................................................96
3.8.1 AWS IoT ................................................................................................................................................96
3.8.2 AZURE IoT .............................................................................................................................................99
3.8.3 Private IoT........................................................................................................................................... 102
3.8.4 RMS (Remote Management System) .....................................................................................103
3.9 BACKUP AND RESTORE ...............................................................................................................................109
3.10 FIRMWARE UPGRADE...............................................................................................................................110
3.11 RESET TO DEFAULTS ................................................................................................................................. 111
3.12 SAVE ...................................................................................................................................................112
3.13 LOGOUT ...............................................................................................................................................113
3.14 REBOOT ...............................................................................................................................................113
4. REVISION HISTORY .................................................................................................................................................................114

6
Declaration of Conformity
CE RED (Radio Device Directive)
While you see the CE Marking print in our product, it indicates the product comfort to the
requirement of the CE RED.
We provide the CE RED Declaration of Conformity (DoC) for our Wireless Router, WLAN AP
products in our web site. The DoC includes the Brand Name, Product Name, Model Name,
Description, compliant standards and Manufacture information. Different product may comfort to
different standards of Safety, Health, EMC, Radio and other specific standard. You can download
the formal document of the product in our Web site or apply from our Sales/Technical people.
The DoC in this product manual applied to below models:
Brand Name: WoMaster
Product Name: Industrial Din-Rail /Waterproof IP67 2.4+5GHz 802.11ac Wave 2 MESH
WLAN AP/outer
Model Name: WA512GM-D/IP67, WA512G-D/IP67
Compliant Standard:
Safety: UL62368-1
RF: EN300328, EN301893 B1, EN62311
EMC: EN301489-1/17, EN55032/35, EN61000-3-2/3
Also Complaint with FCC Standard:
RF: Part 15C 2.4G, FCC Part 15E 5G B1/ B4, CFR 2.1091
EMC: FCC Part 15B
The declaration of CE RED is authorized at the following company and address.
WoM Asia.
( Manufacturer Name )
4F, No.86-2, Yiwen 1st St., Taoyuan Dist., Taoyuan 330, Taiwan
( Manufacturer Address )

7
FCC
Federal Communications Commission Statement
This device complies with FCC Rules Part 15. Operation is subject to the following two conditions:
• This device may not cause harmful interference.
• This device must accept any interference received, including interference that may cause
undesired operation.
FCC Caution
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user‘s authority to operate the equipment.
The antenna(s) used for this transmitter must not be co-located or operating in conjunction with
any other antenna or transmitter.
Note: This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own
expense.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. End users must follow the specific operating instructions for satisfying RF exposure
compliance. To maintain compliance with FCC exposure compliance requirement, please follow
operation instruction as documented in this manual.
Radiation Exposure Statement:
This equipment must be installed and operated in accordance with provided instructions and the
antenna(s) used for this transmitter must be installed to provide a separation distance of at least
20 cm from all persons and must not be co-located or operating in conjunction with any other
antenna or transmitter
Installer Compliance Responsibility
Devices must be professionally installed and it is the professional installer’s responsibility to make
sure the device is operated within local country regulatory requirements.
The device is compliance with IEC62368-1, EN62368-1, UL62368-1 Safety Request. Please read
the safety precaution in user manual.

8
SAFETY PRECAUTION
General Notification
SELV: The device is designed for operation with SELV (extra-low voltage). It is powered from DC
source. Connect the unit only to DC power source that complies with the SELV requirements in IEC/EN
62368 based safety standards. The product does Not include the AC power adapter.
Electrical energy source classifications: The design is complaint with the ES1 definition of the
EN62368-1 standard.
This product is intended to be supplied by an external power source (UL listed / IEC 60950-1 / IEC
62368-1) which output is complied with ES1, PS2/LPS, output rating 24 Vdc (10-50 Vdc), 0.5 A min.(DC
Terminal Block) or 48 Vdc, 0.5 A min.(PoE Input), ambient temperature 70 °C minimum.
The power cord of adapter should be connected to a socket outlet with an earthing connection,
except for the adapter is complied with Class II construction.
High temperature warning for IEC/EN 60950
(1) This equipment is intended to be used in Restrict Access Location. The access can only be gained
by Skilled person or by Instructed person who have been instructed about the metal chassis of the
equipment is so hot that Skilled person have to pay special attention or take special protection. Only
authorized by well trained professional person can access the restrict access location.
(2) External metal parts are hot!! Before touching it, special attention or protection is necessary.
Classification of use by: Please read the safety precaution and the user manual first before install the
product. The ordinary person is only allowed to connect low voltage (<60V) power connector and
configured the software settings. If you need to change the power system, reallocated the hardware
installation, you MUST get approval and handled by skilled person. If you don’t get exact info you
need, you can contact our technical people of distributor or contact us by email:
[e-mail]
Power
For power connection, make sure the following requirement are met:
Power Specification: Follow the power installing instruction of the user manual, it indicates the
available input voltage range, V+/V- pin assignment, power consumption and other notice.

9
Power Source: External power source must be UL listed / IEC 60950-1 / IEC 62368-1 compliant. In
practical, the SELV DC product has no internal DC/DC isolation design. For external power, it is
suggested to use isolated AC to DC or DC to DC power design PSU for installation. The output voltage
and current of the Power Supply conforms to the range of the input voltage and inrush current of the
equipment. Its minimum ambient temperature is equal to maximum operating temperature of the
product.
Switch ON Notice: Only switch on the supply voltage while the housing is closed, the input voltage is
correct and the terminal blocks are wired correctly.
Wiring: The connection cables used are permitted for the specified electronic voltage, current, wire
diameter and temperature range. For DC voltage, it is at least 1.0mm, AWG16.
Grounding: Besides the PSU selection, the Power Supply must be well installed, includes grounded and
other notices which are defined in its instruction guide. The well digital/earth grounding is important
and make sure everything is done correctly before power on the system.
High Voltage Station Notice: If the product is installed inside the high voltage cabinet/station, for
example the Wind power tower is usually 690V power system, shut down the power system before
user go into the tower. The error 690V will kill your life and can not be cured. This is usually defined in
the Safety Precaution of the high voltage station, just remind again here for warming.
Environment & Housing
Only operate the device at the specified ambient temperature and humidity. The temperature of the
surrounding air means a distance of up to 5cm from the device. While installing multiple devices
within the cabinet, remains suitable width between the devices is MUST for better heat dispersing.
Hot surface. The enclosure is metal housing with rugged heat dispersing heat sink on top.
Reserve some space for top heat sink can have better heat dispersing. Avoid touching the device while
it is operating, especially in high temperature environment.
NOT allow to open the housing: Only technicians authorized by the manufacturer are permitted to
open the housing. Without the manufacturer permitted, open the housing means the product is not
warrantied and no responsible for any unexpected risk.
IP Degree: Connect the equipment which meets the IP degree of protection requirements for the
application case.
Installation
Devices must be professionally installed and it is the professional installer’s responsibility to make sure
the device is operated within local country regulatory requirements.
The classification of Machine energy source is MS1. According to the definition, the product can be

10
installed <2m height environment.
Indoor Area:
The product (WA512GM Series, WR312/322/212/222/224) is defined as indoor product. Most of the I/O
interface is connected inside the cabinet/box, for example the power terminal block, USB and RJ-45
connectors.
Note of the WR319/329 Series: The RJ-45 Ethernet LAN ports (port 1~8) is only allowed to be installed
within indoor area. Only the RJ-45 Ethernet WAN port (port 9) can be connected to external device
outside the box.
USB: The attached USB socket is defined for device maintenance purpose only. Do NOT use it for other
purpose, especially for charging the battery by the USB is restricted. If the device is damaged due to
the restricted behavior, this is not included in product warranty range. (WA512G-IP67, WR312/322,
WR316, WR319/329 Series supports USB interface.)
Grounding: The equipment must be grounded. Ground the device before connecting the Ethernet
cables, RF antenna, antenna cables and power supply. Contact the appropriate electrical inspection
authority or an electrician if you are uncertain that suitable grounding is available.
WLAN Plan
Professional Wireless IT: If you are installing the equipment in the factory, station, open area…, the
professional Wireless IT Engineer can provide better service for AP location, channel and field plan to
get better performance and coverage.
RF (Radio Frequency) Notice:
Read the Radio output power, receiver sensitivity, antenna gain specification before installing.
The shipped products and antenna comforts to the CE request and allowed to be used in all
European countries. It also comfort to the FCC request and allowed to be used in USA.
When installing external antennas, the Radio Output power and antenna gain value must be
allowed according to the regulations of the country.
When the system is operational with high gain antenna, avoid standing directly in front of it.
Strong RF fields are present when the transmitter is on.
When the system is operational with high gain antenna in short distance, adjust the radio output
lower (still within the regulation of the country). Strong output power plus high gain antenna is
not good installation for short distance transmission.
Metal Limitation: Install the device in a cabinet or in an operating site with limited access, the metal
cabinet will filter the radio signals, use the extended antenna cable and install the external antenna in
free space helps to get better Radio signal.
Note that You are responsible for undertaking suitable lightning protection. The Field EMD

11
(Lightning) DAMAGE IS NOT COVERED UNDER WARRANTY.
PoE (Only for PoE model)
The product supports standard PoE Input, please make sure the voltage range of PSE comforts to the
standard PoE request. The voltage range of the 802.3at definition is 50~57V, 802.3af is 46~57V.
According to the PoE/PoE+ definition, the maximum current through the Ethernet cable is
600mA/802.3at or 350mA/802.3af, the CAT 5E or above standard cable is suggested and the maximum
Ethernet cable distance is less than 100m.
Users MUST use the safety certificated PoE Switch, PoE Injector and Power Supply. The Industrial PoE
Switch and PoE injector/adapter is recommended.
Be notice the maximum power consumption of the product, it is NOT allowed to connect over the
specification.
This wireless AP/Client, WA512GM Series supports one 802.3af PD (Power Device) port as power input.
There is no PoE output functionality.
When this equipment (WA512GM Series) is to be connected to Power in PoE networks, which would
be not routing to outside plants.

12
1. Introduction
1.1 Overview
WA512G series is designed for IIoT application by dual band concurrent Wireless LAN Radio. WA512G is
equipped with high performance Quad core ARM processor with 5GHz IEEE 802.11ac Wave 2 and 2.4G
802.11n WLAN radio, up to 866M+300Mbps high throughput, 2 Gigabit Eth ernet port are able to support
Bridge/Router mode and powered by 802.3af PoE switch. It supports MESH self -healing wireless network,
DHCP Server, NAT and secure VPN connectivity can reach 150Mbps IPsec performance in 256 -bit encryption.
Model Name
Description
IP67 Series
WA512GM-IP67-E
Industrial 802.11ac Din-Rail Dual Radio 2.4+5GHz Concurrent Wireless Mesh AP, 802.11ac Wave 2 +
802.11b/g/n WLAN, 2GE, USB, IP67 Enclosure, EU-plug
WA512GM-IP67-U
Industrial 802.11ac Din-Rail Dual Radio 2.4+5GHz Concurrent Wireless Mesh AP, 802.11ac Wave 2 +
802.11b/g/n WLAN, 2GE, USB, IP67 Enclosure, US-plug
WA512G-IP67-E
Industrial 802.11ac Din-Rail Dual Radio 2.4+5GHz Concurrent Wireless AP/Client, 802.11ac Wave 2 +
802.11b/g/n WLAN, 2GE, USB, IP67 Enclosure, EU-plug
WA512G-IP67-U
Industrial 802.11ac Din-Rail Dual Radio 2.4+5GHz Concurrent Wireless AP/Client, 802.11ac Wave 2 +
802.11b/g/n WLAN, 2GE, USB, IP67 Enclosure, US-plug
DIN-Rail Series
WA512GM-D
Industrial 802.11ac Din-Rail Dual Radio 2.4+5GHz Concurrent Wireless Mesh AP, 802.11ac+802.11b/g/n
WLAN, 2GE, Din-Rail, 24VDC Terminal Block
WA512G-D
Industrial 802.11ac Din-Rail Dual Radio 2.4+5GHz Concurrent Wireless AP/Client, 802.11ac+802.11b/g/n
WLAN, 2GE, Din-Rail, 24VDC Terminal Block

13
1.2 Major Features
Below are the major features of WA512G Series:
- Quad-Core ARM Processor
- IEEE 802.11ac Wave 2, compatible with 802.11a/b/g/n
- Concurrent dual-band 2.4 G+5GHz radio, up to 866Mbps + 300Mbps Bandwidth
- 2x SMA/N-type Antenna socket for 2.4GHz + 5GHz DBDC (Dual Band Dual Concurrent)
- Dual Gigabit Ethernet ports in Router mode for WLAN/LAN to Eth-WAN routing
- Support IEEE 802.3af PoE P.D. Input
- Qualcomm® Wi-Fi SON MESH Technology (WA512GM Series)
Self-Healing auto rerouting through multi-hop (up to 4 hops and 10 nodes)
Self-Configuring Plug-and-play via Wireless network with ViewMaster utility
- Enhanced Cyber Security & Redundancy
Support Firewall for inbound/outbound traffic
OpenVPN (server/client), IPsec for secure remote connection
IPSec Performance >150Mbps @256-bit encryption
Support L2TP with PPP, PAP, CHAP(LCP, IPCP)
HTTPs/SSH secure login
Support TACACS+ multi-user authentication for privileged user management
- Support Industrial IoT Cloud Server, AWS, Azure, Private IoT and communication protocol
- Support Network management utility ViewMaster and NetMaster NMS
- Support Private cloud management server ThingMaster, ThingMaster OTA for Remote Management
- Slim size 110x106x40mm Din-Rail mounting design (WA512GM/WA512G-D)
- Support 24V(9-50V) DC Input (WA512GM/WA512G-D)
- Support IP67 enclosure for industrial application (WA512GM/WA512G-IP67)
- Wide range operating temperature -40~70˚C

14
2. Installation
This chapter introduces mechanical and contains information on installation and configuration procedures.
2.1 WA512G (IP67 Housing)
2.1.1 Dimension
Dimensions of WA512G-IP67: 239mm(H) x 269mm(H) x 68mm (D) / without mounting clip
2.1.2 Product Appearance

15
2.2.3 Product Package
Standard package includes:
1x Product Unit
1x Quick Installation Guide
1x PoE Injector with AC Plug
3x Cable Gland
1x Mounting kit
*Note: Antenna not included
2.2.4 Interface Installation
After unpacking the box, follow the steps below in order to properly connect the device.

16
2.2.4.1 Wiring Power Input
Standard package includes a PoE injector to power on WA512G-IP67 series. WA512G is a standard IEEE 802.3
PoE P.D. device and can also be power by PoE switch (P.S.E).
Wiring the Power Input through PoE Injector
1) Install PoE injector power cord.
2) Install Ethernet cable between PoE ports of WA512G and PoE injector.
3) Install Ethernet cable between LAN ports of WA512G and PC/NB whenever proceeding WebGUI
configuration.
Wiring the Power Input through PSE switch
1) Install Ethernet cable between PoE ports of WA512G and PSE switch
2) Install Ethernet cable between LAN ports of WA512G and PSE switch whenever proceeding WebGUI
configuration.

17
2.2.4.2 Wiring Antenna
Antenna Socket on device - N-type female
The antenna socket is N-type female and located on the top of the device. The
antenna is usually installed in the upper/upward position. You can install the
external antennas or you can install an antenna cables to connect to a long-distance antenna.
Antenna/Antenna Cable - N-type male
You can wire the waterproof antenna with N-type Male connector directly to the
N-female socket on the top of the device. For safely installation, it is usually applied for
short length, lower gain omni-antenna.
You can also Wire extended antenna cable with N-type Male connector to connect the
external antenna.
Please noted that the longer RF cable must cause more signal lost, the shorter the more suitable. The RF
cable quality is also important for the extended antenna installation. We
recommend the high quality RF cable, for example the RF400 50ohm LOW
LOSS COAXIAL CABLE with UV RESISTANCE.
Note: In field installation, the RF Surge Arrestor is also important for product safety.
RF Surge Arrestors
RF surge arrester is also known as cable free coaxial lightning
arrestors/suppressors. It is used for antenna feeder equipment,
it can protect the communication device from the lightning
strike. The arrestor features an N-type male and an N-type
female connector to connect the extended RF cable. An earth
bond connection must be created using the shortest path to the
ground.

18
2.2.4.3 Wiring Waterproof Connector
As shown in the figure, there are some steps to wire the waterproof connectors.
Step 1~3: Lock the waterproof cover for the unused RJ45, USB and LED light connectors. The steps can be done
before go to the field.
Step 4~7: Wiring Ethernet cable. Since the Ethernet cable length is not fixed in every site, the steps are usually
done in the field. Connect the Ethernet cable to the waterproof cable gland in sequence. If your RJ45 crystal
connector is larger than the aperture, you must thread the cable before pressing the RJ45 crystal connector.
Lock the Ethernet connector with cable gland finally.
Step 8: After completing the installation of the connector, please check whether the Ethernet cable and the
waterproof cable gland are fastened, and inject waterproof silicone to avoid water leakage.

19
2.2.5 Mounting the AP
Mount the AP on a Pole/Wall
1) Screw up the attached mounting plate and the Access Point by screw A (M5, 15mm).
2) Screw up the mounting kit between pole and Access Point.
3) Mount the Access Point steadily to the pole by locking the pole mounting kit tightly. The antenna is installed
in the upper/upward position. While installed the AP in high tall factory, the AP is also available by pole
mounting on the ceiling.
4) You can also mount the Access Point steadily to the wall by locking the wall mounting plate tightly. The
antenna is installed in the upper/upward position. You can use the attached screw B and its expansion screw.
While using other type screw for wall-mounting, make sure the device is fixed well.
5)The mount plate can be installed in Horizontal or Vertical direction, refer to the below steps.
Mounting plate in Horizontal installation (The N-Type Antenna socket is in upper/upward side.)

20
Mounting plate in Vertical installation (The N-Type Antenna socket is in upper/upward side.)
2.2.6 LED
Check system status through LED connector.
WA512G-IP67 series
LED
Status
Description
5GHz
Amber On
AP mode
Amber Blinking
Station mode client connected
Off
Station mode/radio disabled
2.4GHz
Green On
AP mode
Green Blinking
Station mode client connected
Off
Station mode/radio disabled
Power
Red On
Power On
Off
Not Receiving Power