Gibson GES831CS0 User manual

P/N 131593000A (0403)
Printed in U.S.A.

2
For your safety, the information in this manual must be followed to minimize the risk of fire
or explosion or to prevent property damage, personal injury or loss of life.
-Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other
appliance.
- WHAT TO DO IF YOU SMELL GAS:
•Do not try to light any appliance.
•Do not touch any electrical switch; do not use any phone in your building.
•Clear the room, building or area of all occupants.
•Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions.
•If you cannot reach your gas supplier, call the fire department.
Installation and service must be performed by a qualified installer, service agency or the gas supplier.
Important Safety Instructions
Read all instructions before using this laundry center.
To reduce the risk of fire, electrical shock, or injury to persons when
using this laundry center, comply with the basic warnings listed below.
Failure to comply with these warnings could result in serious personal injuries.
Prevent Fire
Do not wash or dry items that have been previously cleaned in,
soaked in, or spotted with gasoline, cleaning solvents, kerosene, waxes, etc. Do not
store these items on or near the dryer. These substances give off vapors that could
ignite or explode.
Do not place items exposed to cooking oils in your dryer. Items
contaminated with cooking oils may contribute to a chemical reaction that could
cause a load to catch fire.
Do not put oily or greasy rags or clothing on top of the laundry center.
These substances give off vapors that could ignite the materials.
Do not add gasoline, cleaning solvents, or other flammable or
explosive substances to the wash water. These substances give off vapors that could
ignite or explode.
Under certain conditions, hydrogen gas may be produced in a hot
water system that has not been used for 2 weeks or more. HYDROGEN GAS IS
EXPLOSIVE. If the hot water system has not been used for such a period, before
using the washer, turn on all hot water faucets and let the water flow from each for
several minutes. This will release any accumulated hydrogen gas. Hydrogen gas
is flammable; do not smoke or use an open flame during this time.
To prevent fire, do not use heat to dry items containing plastic, foam
rubber or similarly textured rubber-like materials, or items containing feathers or
down. Use Air Fluff (No Heat) only.
©1996 White Consolidated Industries, Inc.
All rights reserved.
Product Registration
Thank you for choosing this laundry
center. This owner's guide will explain
proper operation and care.
Record Your Model and Serial
Numbers
Record below the model and serial
numbers found on the laundry center
serial plate located on the inside of the
dryer door. Keep these numbers for
future reference.
Model Number __________________
Serial Number ___________________
Date of Purchase ________________
Register Your Product
The self-addressed PRODUCT
REGISTRATION CARD should be filled in
completely, signed and returned.
Versión en español
Si desea obtener una copia en español
de este Manual del Usuario, sírvase
escribir a la dirección que se incluye a
continuación. Solicite la P/N 131547000.
Spanish Owner's Guides
Frigidaire Company
P. O. Box 9061
Dublin, Ohio 43017-0961
Contents
Versión en español ..................... 2
Product Registration ........................ 2
Important Safety Instructions ........ 2-3
Washing Procedures ..................... 5-7
Stain Removal ............................. 7-8
Common Washing Problems ........... 9
Drying Procedures ......................... 10
Features........................................ 11
Common Drying Problems ............ 11
Care and Cleaning .................. 12-13
Avoid Service Checklist ............ 13-15
Warranty and Service .................... 16

3
Clean the dryer lint screen before or after each load. The interior of
the dryer, lint screen housing and exhaust duct should be cleaned approximately
every 18 months by qualified service personnel. An excessive amount of lint build-up
in these areas could result in inefficient drying and possible fire. See Care and
Cleaning, pages 12-13.
Do not operate the dryer if the lint screen is blocked, damaged or
missing. Fire hazard, overheating and damage to fabrics can occur. If your dryer has
a drying rack, always replace the lint screen when finished using the drying rack.
Keep area around the exhaust opening and surrounding areas free
from the accumulation of lint, dust and dirt.
Do not obstruct the flow of ventilating air. Do not stack or place
laundry or throw rugs against the front or back of the laundry center.
Do not spray any type of aerosol into, on or near laundry center at any
time.
Do not use fabric softeners or products to eliminate static unless
recommended by the manufacturer of the fabric softener or product.
Failure to comply with these warnings could result in fire, explosion, serious bodily
injury and/or damage to the rubber or plastic parts of the laundry center.
Protect Children
Do not allow children to play on or in the laundry center. Close
supervision of children is necessary when the laundry center is used near children. As
children grow, teach them the proper, safe use of all appliances.
Destroy the carton, plastic bag and other packing materials after the
laundry center is unpacked. Children might use them for play. Cartons covered with
rugs, bedspreads or plastic sheets can become airtight chambers.
Keep laundry products out of children's reach. To prevent personal
injury, observe all warnings on product labels.
Before the laundry center is removed from service or discarded,
remove the washer lid and dryer door to prevent accidental entrapment.
Failure to comply with these warnings could result in serious personal injuries.
This Owner's Guide provides general
operating instructions for your laundry
center. It also contains information
about features for several other
models. Your laundry center may not
have every feature included.
Use the laundry center only as
instructed in this Owner's Guide and
the Operating Instructions cards
included with your laundry center.
Note: The instructions appearing in this
Owner's Guide are not meant to cover
every possible condition and situation
that may occur. Common sense and
caution must be practiced when
installing, operating and maintaining
any appliance.
CORRECTCORRECT
CORRECTCORRECT
CORRECT
Use this way ONLYUse this way ONLY
Use this way ONLYUse this way ONLY
Use this way ONLY
Grounding type
w
all receptacle
Power supply
cord with 3-prong
grounding plug
Do not under
any circumstances
cut, remove,
or bypass
the grounding prong
from this plug.
Avoid fire hazard or
electrical shock. Do not use an adaptor
plug or extension cord or remove
grounding prong from electrical power
cord. Failure to follow this warning can
cause serious injury, fire or death.

4
Prevent Injury
To prevent shock hazard and assure stability during operation, the
laundry center must be installed and electrically grounded by a qualified service
person in accordance with local codes. Installation instructions are packed in the
laundry center for the installer's reference. Refer to INSTALLATION INSTRUCTIONS
for detailed grounding procedures. If the laundry center is moved to a new location,
have it checked and reinstalled by a qualified service person.
To prevent personal injury or damage to the laundry center, the
electrical power cord must be plugged into a properly grounded and polarized 3-
prong outlet. The third grounding prong must never be removed. Never
ground the laundry center to a gas pipe. Do not use an extension cord or an
adaptor plug.
Follow package directions when using laundry products. Incorrect
usage can produce poisonous gas--resulting in serious injury or death.
• Do not combine laundry products for use in 1 load unless specified on the label.
• Do not mix chlorine bleach with ammonia or acids such as vinegar.
To prevent serious personal injury and damage to the laundry center:
• All repairs and servicing must be performed by an authorized servicer
unless specifically recommended in this Owner's Guide. Use only authorized
factory parts.
• Do not tamper with controls.
• Do not install or store the laundry center where it will be exposed to the
weather.
ALWAYS disconnect the laundry center from the electrical supply
before attempting any service or cleaning. Failure to do so can result in electrical
shock or injury.
Do not use any type spray cleanser when cleaning dryer interior.
Hazardous fumes or electrical shock could occur.
To prevent injury, do not reach into the washer while parts are
moving. Before loading, unloading or adding items, push in the cycle selector knob
and allow the tub to coast to a complete stop before reaching inside.
To prevent injury, do not reach into the dryer if the drum is moving.
Wait until the dryer has stopped completely before reaching into the drum.
A thermal limiter switch automatically turns off the dryer motor in the unlikely
event of an overheated situation (electric dryers only). A service technician must
replace the thermal limiter switch after correcting the fault.
The washer is equipped with an electrical overload protector. The motor will stop
if it becomes overheated. The washer will automatically restart after a cool down
period of up to 30 minutes, if the washer has not been manually turned off during
this time.
Important SafetyImportant Safety
Important SafetyImportant Safety
Important Safety
InstructionsInstructions
InstructionsInstructions
Instructions (continued)(continued)
(continued)(continued)
(continued)
Do not use or mix
liquid chlorine bleach with other
household chemicals such as toilet
cleaners, rust removers, acid or
productscontaining ammonia.These
mixtures can produce dangerous
fumes which can cause serious injury
or death.

5
WW
WW
Washing Prashing Pr
ashing Prashing Pr
ashing Procedurocedur
ocedurocedur
ocedureses
eses
es • Follow the guidelines below for preparing the wash load.
• Read the Washer Operating Instructions card for operating your specific
model.
•Always read and follow fabric care and laundry product labels.
To reduce the risk of fire, electrical shock, or injury to persons, read
Important Safety Instructions, pages 2-4, before operating this washer.
1. Sort laundry into loads that can be washed together.
Sort items by recommended water temperatures, wash time, and agitate/spin
speeds.
• Separate white, light, and colorfast items from dark and noncolorfast items.
• Separate items which shed lint from items which attract lint. Permanent
press, synthetic, knit and corduroy items will pick up lint from towels, rugs
and chenille bedspreads.
• Separate heavily soiled items from lightly soiled items.
• Separate lacy, sheer and loosely knit items from sturdy items.
2. Prepare items for washing.
• Empty pockets.
• Brush off lint and dirt. Shake out rugs and beach towels.
• Close zippers, fasten hooks, tie strings and sashes, and remove nonwashable
trims and ornaments.
• Remove pins, decorative buttons, belt buckles, and other objects which
could be damaged. This also helps protect other items in the wash load.
• Mend rips and tears to prevent further damage during washing.
• Place delicate items such as bras, shoulder pads, hosiery, and belts in a mesh
bag to prevent tangling during the wash cycle.
• Turn knit items inside out to prevent pilling.
3. Pretreat stains and heavy soil.
See Stain Removal, pages 7-8, for details.
4. Add a measured amount of detergent to the wash tub
before adding the laundry load.
Follow detergent manufacturer's directions. The amount required depends on
type of detergent, load size and soil level, and water hardness.
5. If desired, add liquid bleach to Bleach Dispenser (some models).
• Before adding the wash load, add liquid bleach to bleach dispenser located
in left front corner under the lid:
• 3/4 cup (180 ml) for small loads
• 1 cup (240 ml) for large loads
• 1-1/4 cups (300 ml) for extra-large loads.
• Then add 1 cup (240 ml) water to flush the dispenser.
• Do not use powdered bleach in the bleach dispenser.
For models without a bleach dispenser, dilute the recommended amount of
liquid chlorine bleach in 1 quart (.95 L) water. Add it to wash water after
a few minutes of agitation. Do not pour bleach directly on wash load.
BleachDispenser(somemodels)
Place delicate items in a mesh bag.
Emptypockets.
Sort laundry into loads that can be
washedtogether.

6
WW
WW
Washing Prashing Pr
ashing Prashing Pr
ashing Procedurocedur
ocedurocedur
ocedureses
eses
es
(continued)(continued)
(continued)(continued)
(continued)
6. Add laundry load to washer.
• Dry load level should not be higher than top row of holes in wash tub.
Do not overload washer.
• Do not put items on top of agitator or wrap them around it. Load items
evenly.
• Combine large and small items in a load. Load large items first. Large items
should not be more than half the total wash load.
• When washing a single heavy item, add 1 or 2 towels to balance the load.
7. If desired, add liquid fabric softener to Fabric Softener
Dispenser (some models).
For models with a built-in dispenser (see picture below to the left):
1. Add liquid softener to the dispenser, following fabric softener label directions.
2. Add water to bring liquid level to fill line on dispenser cap.
3. Remove the dispenser from the agitator after each use. Rinse both cap and
cup with warm water. Replace dispenser in the agitator.
IMPORTANT: Do not stop and restart washer during a spin when using the
fabric softener dispenser.
For models with a removable dispenser (see picture below to the left):
1. Attach fabric softener dispenser to top of agitator by pressing down gently.
2. Add softener to the dispenser, following fabric softener label directions.
3. Add water to bring liquid level to top of the peg in the center of the cup.
4. Remove the dispenser from the agitator after each use. Rinse both lid and
bowl thoroughly with warm water. Reassemble and place dispenser on
agitator or store it nearby.
IMPORTANT: Do not stop and restart washer during a spin when using the
fabric softener dispenser.
For models without a fabric softener dispenser, follow fabric softener label
directions. Add diluted fabric softener to the final rinse. Do not pour fabric
softener directly on the wash load.
8. Set cycle selector knob and washer controls according to
type, size, and soil level of each load, and detergent used.
See Washer Operating Instructions card for your specific model controls.
Donot use liquidchlorine bleach with
otherhouseholdchemicals.
RemovableFabricSoftenerDispenser
(somemodels)
Donot load items above
top row of holes in wash tub.
Built-InFabricSoftenerDispenser
(somemodels)

7
9. Start the washer.
Close the washer lid and pull out the cycle selector knob. Washer will fill and
agitate with the lid open. The tub will not spin unless the lid is closed.
• To stop the washer, push in the cycle selector knob.
• To change a cycle, push in the cycle selector knob. Turn it clockwise to the
desired setting. Pull out the knob to restart the washer.
10.Remove items when the cycle is completed.
For your safety, the lid locks when the tub is spinning. It will remain locked for
about 1 minute after the tub stops spinning.
• To open the lid during a spin, push in the cycle selector knob and wait about
1 minute for the lid lock to release. Do not force open the locked lid.
Place washed items in automatic dryer, line dry, or dry flat as directed by fabric
care label. Excess wrinkling, color transfer or odors may develop in items left in
the washer after the cycle has ended.
Stain RemovalStain Removal
Stain RemovalStain Removal
Stain Removal Safe Stain Removal Procedures
To reduce the risk of fire or serious injury to persons or property,
comply with the basic warnings listed below:
• Read and comply with all instructions on stain removal products.
• Keep products in their original labeled containers and out of children's
reach.
• Thoroughly wash any utensil used.
• Do not combine stain removal products, especially ammonia and chlorine
bleach. Dangerous fumes may result.
• Never wash items which have been previously cleaned in, washed in,
soaked in or spotted with gasoline, dry cleaning solvents or other flammable
or explosive substances because they give off vapors that could ignite or
explode.
• Never use highly flammable solvents, such as gasoline, inside the home.
Vapors can explode on contact with flames or sparks.
For successful stain removal:
• Remove stains promptly.
• Determine the kind of stain, then follow recommended treatment in the
stain removal chart on the next page.
• To pretreat stains, use a prewash product, liquid detergent, or a paste made
from granular detergent and water.
• Use cold water on unknown stains because hot water can set stains.
• Check care label instructions for treatments to avoid on specific fabrics.
• Check for colorfastness by testing stain remover on an inside seam.
• Rinse and wash items after stain removal.
Followfabriccarelabelinstructions.
Do not combine stain removal products.

8
STAINSTAIN
STAINSTAIN
STAIN
Adhesive tape, chewing
gum, rubber cement
Baby formula, dairy
products, egg
Beverages (coffee, tea,
soda,
juice, alcoholic beverages)
Blood
Candle wax, crayon
Chocolate
Collar or cuff soil, cosmetics
Dye transfer on white
fabric
Grass
Grease, oil, tar (butter, fats,
salad dressing, cooking oils,
car grease, motor oils)
Ink
Mildew, scorch
Mud
Mustard, tomato
Nail polish
Paint, varnish
Perspiration
Rust, brown or yellow
discoloration
Shoe polish
Urine, vomit, mucus, feces
Apply ice. Scrape off excess. Place stain face down on paper towels. Saturate with prewash stain remover or
nonflammable dry cleaning fluid.
Use product containing enzymes to pretreat or soak stains. Soak for 30 minutes or more. Wash.
Pretreat stain. Wash using cold water and bleach safe for fabric.
Rinse with cold water. Rub with bar soap. Or, pretreat or soak with product containing enzymes. Wash using
bleach safe for fabric.
Scrape off surface wax. Place stain face down between paper towels. Press with warm iron until wax is
absorbed. Replace paper towels frequently. Treat remaining stain with prewash stain remover or nonflammable
dry cleaning fluid. Hand wash to remove solvent. Wash using bleach safe for fabric.
Pretreat or soak in warm water using product containing enzymes. Wash using bleach safe for fabric.
Pretreat with prewash stain remover or rub with bar soap.
Use packaged color remover. Wash using bleach safe for fabric.
Pretreat or soak in warm water using product containing enzymes. Wash using bleach safe for fabric.
Scrape residue from fabric. Pretreat. Wash using hottest water safe for fabric. For heavy stains and tar, apply
nonflammable dry cleaning fluid to back of stain. Replace towels under stain frequently. Rinse thoroughly. Wash
using hottest water safe for fabric.
Some inks may be impossible to remove. Washing may set some inks. Use prewash stain remover, denatured
alcohol or nonflammable dry cleaning fluid.
Wash with chlorine bleach if safe for fabric. Or, soak in oxygen bleach and hot water before washing. Badly
mildewed fabrics may be permanently damaged.
Brush off dry mud. Pretreat or soak with product containing enzymes.
Pretreat with prewash stain remover. Wash using bleach safe for fabric.
May be impossible to remove. Place stain face down on paper towels. Apply nail polish remover to back of stain.
Repeat, replacing paper towels frequently. Do not use on acetate fabrics.
WATER BASED: Rinse fabric in cool water while stain is wet. Wash. Once paint is dry, it cannot be removed. OIL
BASED AND VARNISH: Use solvent recommended on can label. Rinse thoroughly before washing.
Use prewash stain remover or rub with bar soap. Rinse. Wash using nonchlorine bleach in hottest water safe for
fabric.
For spots, use rust remover safe for fabric. For discoloration of an entire load, use phosphate detergent and
nonchlorine bleach. Do not use chlorine bleach because it may intensify discoloration.
LIQUID: Pretreat with a paste of granular detergent and water. PASTE: Scrape residue from fabric. Pretreat
with prewash stain remover or nonflammable dry cleaning fluid. Rinse. Rub detergent into dampened area.
Wash using bleach safe for fabric.
Pretreat or soak in product containing enzymes. Wash using bleach safe for fabric.
TREATMENTTREATMENT
TREATMENTTREATMENT
TREATMENT
Stain RemovalStain Removal
Stain RemovalStain Removal
Stain Removal

9
•Add detergent before wash load. Then
start washer.
•Dilute fabric softener with water.
•Sort items by soil level and color.
•Use correct amount of detergent, hottest
water and bleach safe for fabric.
•Use correct amount of detergent and
hottest water safe for fabric.
•Do not pour liquid fabric softener
directly on fabric. See package directions
or Washing Procedures for proper
diluting.
•Never pour chlorine bleach directly on
fabric.
•Check condition of items before washing.
See Washing Procedures for preparing
and loading the wash load.
•See Washing Procedures for sorting and
preparing the wash load.
•Do not overload washer.
•Use correct amount of detergent, water
temperature and water level.
•Use fabric softener in the washer to
lubricate fibers.
•When ironing, use spray starch or fabric
finish on collars and cuffs.
•Turn items inside out to reduce abrasion.
•Increase water temperature using hottest
water safe for fabric.
•Do not overload washer.
•Use liquid detergent or use
nonprecipitating water conditioner with
nonphosphate granular detergent.
•Do not overload washer.
•Remove items from washer as soon as
cycle is completed.
•Use liquid fabric softener.
•Wash synthetics frequently using water at
least 100°F (37°C ) and correct water level.
•Use nonprecipitating water softener.
•Before washing, run hot water for a few
minutes to clear lines.
•Drain water heater occasionally.
•For an ongoing problem, install an iron
filter in your water supply system.
Common WCommon W
Common WCommon W
Common Washing Prashing Pr
ashing Prashing Pr
ashing Problemsoblems
oblemsoblems
oblems
SOLUTIONSSOLUTIONS
SOLUTIONSSOLUTIONS
SOLUTIONS
PROBLEMPROBLEM
PROBLEMPROBLEM
PROBLEM PREVENTIVE MEASURESPREVENTIVE MEASURES
PREVENTIVE MEASURESPREVENTIVE MEASURES
PREVENTIVE MEASURES
•If caused by detergent, mix 1 cup (240
ml) white vinegar with 1 quart (.95 L)
water in a plastic container. Soak item 1
hour. Rinse.
•If caused by fabric softener, rub stains
with bar soap. Wash.
•Rewash with correct amount of
detergent and hottest water safe for
fabric. Add bleach safe for fabric.
•Treat with prewash stain remover or
liquid detergent.
•Increase detergent and water
temperature. Rewash.
•Rub fabric softener stains with bar soap.
•May be irreversible if rips, tears and
seams cannot be mended.
•Reduce load size. Rewash using correct
water temperature, water level, and
amount of detergent.
•Add nonprecipitating water conditioner
to wash water.
•Add liquid fabric softener to final rinse.
•Dry load in dryer.
•Remove lint with lint brush or roller.
•Use a lint brush or shaver to remove
pills.
•Reduce load size.
•Add dissolved detergent to tub . Rewash
load.
•Mix 1 cup (240 ml) white vinegar to 1
gallon (3.8 L) warm water in plastic
container. Soak item. Rinse and rewash.
•Reduce load size.
•Rinse in cold water with liquid fabric
softener.
•Soak in detergent booster or product
containing enzymes.
•Wash in hot water (120°F/49°C) using full
permanent press cycle. Increase
detergent.
Add bleach safe for fabric.
•Or, treat with color remover.
•To restore discolored load of whites, use
rust remover safe for fabric.
Do not use chlorine bleach to remove
rust stains. It may intensify
discoloration.
POSSIBLE CAUSESPOSSIBLE CAUSES
POSSIBLE CAUSESPOSSIBLE CAUSES
POSSIBLE CAUSES
Many washing problems involve poor soil and stain removal, residues of lint and scum, and fabric damage. For satisfactory washing
results, follow these suggestions provided by The Soap and Detergent Association.
•Detergent or liquid fabric softener
did not dissolve or disperse.
•Not enough detergent.
•Wash water temperature too
low.
•Incorrect sorting.
•Not enough detergent.
•Undiluted liquid fabric softener
poured directly on fabric.
•Incorrect use of chlorine bleach.
•Unfastened zippers, hooks,
buckles.
•Rips, tears and broken threads.
•Overloading the washer.
•Degradation of fabric.
•Incorrect sorting.
•Tissues left in pocket.
•Overloading the washer.
•Not enough detergent.
•Undissolved detergent has left
residue.
•Static cling is attracting lint.
•Load washed too long.
•Pilling is normal with synthetic and
permanent press fabrics. This is
due to abrasion from normal
wear.
•Undissolved detergent.
•Some nonphosphate granular
detergents can combine with
hard water minerals to form a
residue.
•Overloading the washer.
•Agitation time too short.
•Wash water temperature too
low.
•Not enough detergent.
•Iron or manganese in water
supply, water pipes, or water
heater.
Blue stains
Discoloration,
graying
Greasy, oily stains
Holes, tears, or
snags
Lint
Pilling
(Fibers break off,
ball up and cling to
fabric)
Residue or powder
on dark items;
Stiff, harsh fabrics.
Wrinkling
Yellow buildup of
body soil on
synthetic fabrics
Yellow or brown
rust stains

10
•Follow the guidelines below for preparing the load for drying.
•Read the Dryer Operating Instructions card for operating your specific model.
• Always read and follow fabric care labels and laundry product labels.
To reduce the risk of fire, electrical shock, or injury to persons, read
Important Safety Instructions, pages 2-4, before operating this dryer.
1. Prepare items for drying.
•Dry items of similar fabric, weight and construction in the same load.
•Separate dark items from light-colored items. Separate items that shed lint
from those that attract lint. If an item sheds lint, turn it inside out.
•Be sure buckles, buttons and trim are heatproof and won't damage the drum
finish. Close zippers, fasten hooks and Velcro®-like fasteners. Tie strings and
sashes to prevent snagging and tangling.
•If possible, turn pockets inside out for even drying.
•Check for stains which may not have been removed in washing. Dryer heat
may permanently set some stains. Repeat stain removal process before
drying.
•Place small items in a mesh bag to prevent tangling and for easy removal.
2. Check that lint screen is clean and in place.
3. Load the dryer.
• The average load will fill the drum 1/3 to 1/2 full. Items need room to tumble
freely for even drying and less wrinkling. Do not overload dryer.
• When drying large items, dry only 2 or 3 at a time. Fill out the load with small
and medium sized items.
• For delicate or very small loads, add 2 lint-free towels for better drying, less
wrinkling, and to prevent grease stains caused by fabric softener sheets.
• Do not overdry items. Overdrying can cause wrinkling, shrinkage, harshness,
and a build-up of static electricity, which can produce more lint.
• If desired, add a dryer fabric softener sheet.
4. Close the dryer door and set dryer controls (some models).
See Dryer Operating Instructions card for your specific model controls.
5. Turn cycle selector clockwise to the desired setting.
6. Start the dryer.
• Push Start button for 2 seconds.
• To add or remove items when the dryer is running, open the door. The dryer
will always stop when the door is opened. Allow the drum to come to a
complete stop before reaching inside.
• To restart dryer, close the door then push Start button. Hold for 1-2 seconds
and release.
7. When the cycle ends, remove items immediately and hang
or fold. If load is removed before the cycle ends, turn cycle selector to OFF.
DrDr
DrDr
Drying Prying Pr
ying Prying Pr
ying Procedurocedur
ocedurocedur
ocedureses
eses
es
Followfabriccarelabelinstructions.
Fill dryer drum 1/3 to 1/2 full.
Place small items in a mesh bag.