GIGA Copper Networks G4200-4T User manual

G4200-4/8T Twisted Pair Switch
Quick Start Guide
GIGA Copper Networks GmbH

1
1. Hardware Descriptions
Panel information:
The front panel is shown as below:
The following table shows the port descriptions.
Label
Description
Console port
Console port with RJ45 connector for connection to a computer for
console control /administration.
The Console port can be used for accessing the OnAccess4200 CLI
(command line interface) for out-of-band management.
Monitor port (MON)
1*10/100/1000BaseT local system provision/monitoring port
G1/G2
2*1GE Ethernet ports for uplink aggregation
XG1/XG2
2*10GE SFP+ Ethernet ports for uplink aggregation
G.hn1~4
G.hn ports for data signal and Phone signal
Master/slave switch
Select master or slave mode
SYNC
Clock SYNC
100~240 V AC INPUT
Connects to AC power supply:100-240VAC 50-60 Hz
Power switch
Open or shut off the power supply
GND
One optional threaded common ground connection.
The following table shows the LED descriptions.
Label
Type
Color
State
Description
PWR
A/B
Power status
Yellow
On
The power is on and supplying the current to
the system
Off
The power is off or it is not supplying the
current to the system
SYS
System status
Green
On
System is started
Off
System does not start
(1*10/100/1000BaseT RJ45)
Ethernet port
(2*GE/10GE SFP/SFP+)

2
G.hn1
G.hn2
G.hn3
G.hn4
G.hn link status
Green
On
The corresponding port connection normal
Off
The link condition is poor or there is no
connection to this port
Yellow
On
The corresponding port connection abnormal
and link quality is poor
Off
The link condition is normal or there is no
connection to this port
XG1/XG2
10G Ethernet link
status
Green
On
The corresponding port connection normal
Off
There is no connection to this port
G.hn
G.hn port status
Green
On
The corresponding port is selected.
Off
The corresponding port is not selected.
Slot
Slot status
On
The corresponding slot is selected.
Off
The corresponding slot is not selected.
G1/G2/
MON
Ethernet link status
Green
On
The connection Rate is 1000Mbps
On
The connection Rate is 10/100 Mbps
Yellow
On
The corresponding port connection normal
Off
There is no connection to this port
Blink
The G1/G2/ MON port is up and this port is
working.
2. Install line card (optional)
Note: Be default, line cards were installed in the chassis before shipped.

3
3. Application Diagram and installation instruction
3.1 Application
3.2 Sync Installation
NOTE
If there is only one G4200-4/8T, you needn’t use SYNC port. But if there
is more than one G4200-4/8T, just only one is the primary and the rest
are secondary. SYNC signal is sent out from the master. Please power
the primary and then the secondary

4
4. Set up
5. G.hn Cable and Connectors
Device
Supported connectors
Supported MIMO
Phone Line MDU
RJ45 8P8C
RJ11 6P6C
RJ11 6P4C
RJ11 4P4C
Y
RJ11 4P2C
N
Phone Line CPE
RJ11 6P6C
RJ11 6P4C
RJ11 4P4C
Y
RJ11 4P2C
N

5
2 Pairs Cable Application
MDU needs to be configured as MIMO mode.
Single Pair Cable Application
MDU needs to be configured as SISO mode.

6
6. Login
6.1 Default Configuration:
Default IP Address
IP Address: 192.168.0.252
IP Sub network: 255.255.255.0
Accounts:
User name: superuser
Password: 123
6.2 Login to web management page
You can browse http://192.168.0.252 and type user name and password
7. Configure IP
You can configure IP Address from “VLAN Management >> VLAN Interface” of left menu