GIGA G4224Tv2 User manual

G4224Tv2 Twisted Pair Switch
Quick Start Guide
GIGA Copper Networks GmbH

1
1. Package List
G4224T *1
Serial Cable *1
Screw kit
Power line
Rj21 line
Wall-mount kits
Sync cable
Grounding wire
2. Hardware Introduction
2.1 Physical Dimensions
•Dimension (W*D*H): 440mm*268mm*44.5mm,19-inch rack-mount, 1U height.
•Case: Aluminum, degree of protection IP30
•Weight: 5.2Kg
•Operating temperature: 0℃ ~ 50℃
•Storage temperature: -25℃ ~ 80℃
•Humidity: 5% ~ 95% RH Non-condensing
•Consumption: No-load ≦55W, Full-load ≦85W

2
2.2 Front Panel
G4224T Front Panel Description:
2.2.1 Panel Description
Label
Description
Ghn1-24
24 * G.hn Wave2 ports (RJ45 connector), MIMO and SISO
MGMT
1 * 10/100/1000BT RJ45 port for device management
10G 1/2
2 * 1000-X/10000-X SFP/SFP+ ports
CON 115200
1 * RJ45 connector RS232 console for connection to a computer control/
administration. The RS-232 console port can be used for accessing the device
CLI (command line interface) for out-of-band management.
USB
USB type-C connector for connection to a computer control/administration.
The driver needs to be installed correctly
SYNC IN/OUT
2 * BNC connectors used for transmitting 50Hz SYNC clock.
POTS-24
24* PSTN Pass through ports (RJ21 connector)
ON/OFF
Power Switch, Turn on or turn off the power supply
INPUT 100~240 VAC
Connect to AC power supply:100-240VAC 50-60 Hz
GND
1 * ground screw
FAN
1 * Pluggable FAN Module
RST
1 * Reset button, press more than 10s to factory configuration

3
2.2.2 LED Description
Label
Type
Color
State
Description
10G 1/2
Uplink SFP/SFP+
ports status
Green
On
Link up
Blinking
Data is transmitting
Off
Link down
MGMT
Management port
status
Green
On
MGMT Port is link up
Off
MGMT Port is link down or link speed is
100Mbps
Yellow
Blinking
Data is transmitting
Off
No data transmission
Ghn1-24
G.hn ports status
Green
On
The G.hn port connection is normal and PHY
rate is high
Off
There is no connection to this port
Yellow
On
The G.hn port connection is normal and PHY
rate is low
Off
There is no connection to this port or the
PHY rate is high and Green LED is On
PWR
Power status
Yellow
On
The power is on and supplying the current to
the system
Off
The power is off or it is not supplying the
current to the system
SYS
System status
Green
On
System is started
Off
System does not start
ALM
Alarm
Red
On
System is in alarm state, such as 50Hz sync
signal is missing, or the fan is fault
Off
The system is in normal state
SYNC
Clock sync state
Yellow
On
50Hz synchronous signal is normal
Off
50Hz sync signal is missing

4
3. Application Diagram and installation instruction
3.1 Application
3.2 Sync Installation
NOTE
If there is only one G4224T, you needn’t use SYNC port. But if there is
more than one G4224T, just only one is the primary and the rest are
secondary. SYNC signal is sent out from the master. Please power the
primary and then the secondary

5
3.3 Chassis Installation
Step 1. Insert the screws
Step 2. Put the G4224T chassis into the 19’’ rack and tighten it.
Step 3. Connect the ground wire and tighten it.
Step 4. Connect power cable, console cable and UTP cable, then power on the chassis
Step 5. Connect client devices(CPE) to the G.hn port of G4224T,if CPEs is connected, the
corresponding G.hn LED will light up as below :
NOTE
If there are more than one G4224T chassis need to be installed, please
left 0.5U space between chassis to achieve better cooling effect

6
4. G.hn Cable and Connectors
Device
Supported connectors
Supported MIMO
Phone Line MDU
RJ45 8P8C
RJ11 6P6C
RJ11 6P4C
RJ11 4P4C
Y
RJ11 4P2C
N
Phone Line CPE
RJ11 6P6C
RJ11 6P4C
RJ11 4P4C
Y
RJ11 4P2C
N
2 Pairs Cable Application
MDU needs to be configured as MIMO mode.

7
Single Pair Cable Application
MDU needs to be configured as SISO mode.
5. Login
5.1 Default Configuration:
Default IP Address
IP Address: 192.168.0.252
IP Sub network: 255.255.255.0
Accounts:
User name: superuser
Password: 123
5.2 Login via WEB Interface
You can browse http://192.168.0.252 and type user name and password

8
6. Configure IP
You can configure IP Address from “VLAN Management >> VLAN Interface” of left menu
7. G4224T-RJ21 PIN Definition (Optional）
RJ21 Pin
Color
RJ21 Pin
Color
G.now
port 1-24
26
Blue
1
White
1
27
Orange
2
White
2
28
Green
3
White
3
29
Brown
4
White
4
30
Gray
5
White
5
31
Blue
6
Red
6
32
Orange
7
Red
7
33
Green
8
Red
8
34
Brown
9
Red
9
35
Gray
10
Red
10
36
Blue
11
Black
11
37
Orange
12
Black
12
38
Green
13
Black
13
39
Brown
14
Black
14
40
Gray
15
Black
15
41
Blue
16
Yellow
16
42
Orange
17
Yellow
17
43
Green
18
Yellow
18
44
Brown
19
Yellow
19
45
Gray
20
Yellow
20
46
Blue
21
Purple
21
47
Orange
22
Purple
22
48
Green
23
Purple
23
49
Brown
24
Purple
24
50
Gray
25
Purple
idle