GILES FSH-2 Installation and operating instructions

Giles E terprises, I c.
An ISO 9001 Registered Company •Committed to Quality
2750 Gunter P rk Drive West • Montgomery, AL 36109 USA
F x: 334.239.4117 • Website: www.gfse.com
Service Hotli e (Toll Free): 800.554.4537 (USA & Ca ada O ly)
Form No. 60200 (Rele se d te: 07/98)(Revision D te: 09/30/12; Rev. G)
FSH-2,
FSH-2A-99
Operations & Service Manual
FOODSERVICE EQUIPMENT
Model: FSH-2A-99

LIMITED WARRANTY
• Sub ect to the terms and conditions of this Limited Warranty as herein stated, all Giles Enterprises,
Inc., Foodservice Equipment and parts purchased new from an authorized Giles Enterprises, Inc.,
representative are warranted as to defects in material or workmanship for a period of 24 months
from the date of installation, provided, however, that with regard to labor costs in connection with
this warranty, see below. All installations must be made by a qualified installing agency in accor-
dance with all applicable codes and/or regulations in the urisdiction in which installed. Limited war-
ranty coverage is extended to the original owner only and is void if the unit is resold.
• During the Limited Warranty period, Giles Enterprises, Inc. will replace or recondition, at its factory,
any part or parts of this unit which Giles Enterprises, Inc. inspectors udge defective, provided the
unit has been sub ected to normal usage, properly installed, operated and serviced. This Limited
Warranty does not cover cosmetic damage, and damage due to acts of God, accident, misuse, alter-
ation, negligence, abuse of the Giles Foodservice Equipment or the use of unorthodox repair meth-
ods. All parts replaced under this Limited Warranty carry only the unexpired term of this Limited
Warranty. Limited Warranty service may be furnished only by an authorized Giles Enterprises, Inc.,
representative.
• If Limited Warranty service is requested, Giles Enterprises, Inc., will send factory-authorized serv-
ice representatives to repair, recondition, replace or inspect units of its manufacture with such labor
being rendered without cost to owner for twenty-four (24) months from the date of installation.
Otherwise, service, including labor and transportation charges or other expenses, in connection
with the removal or installation of any part or parts supplied under this Limited Warranty, are speci-
fied on the original sales contract between the purchaser and the authorized Giles Enterprises, Inc.,
representative.
• Giles Enterprises, Inc. reserves the right to change or improve its equipment and parts in any way
without obligation to alter such equipment or parts previously manufactured.
• Giles Enterprises, Inc. makes no further warranties, express or implied including implied warranties
of merchantability or fitness for a particular purpose, and has no other obligation or liability not
specifically stated herein.
• Repair or replacement as provided under this Limited Warranty is the exclusive remedy. Giles
Enterprises, Inc., shall not be liable for any incidental or consequential damages for breach of any
express or implied warranty on this product, except to the extent prohibited by applicable law. Any
implied warranty of merchantability or fitness for a particular purpose on this product is limited in
duration to the duration of this Limited Warranty.
• Used Giles Enterprises, Inc., Foodservice Equipment or parts or Giles Enterprises, Inc., Foodservice
Equipment or parts not purchased from an authorized Giles Enterprises, Inc., representative, carry
no warranties, express or implied.

iii
Model: FSH-2, FSH-2A-99
Table Of Contents
Safety ........................................................v
afetyOverview....................................................................v
pecific afetyPrecautions...........................................................vi
1. Intr ducti n..............................................1
1-01. Construction..............................................................1
1-02. tandardFeatures..........................................................1
1-03. OptionalFeature...........................................................1
1-04. pecifications.............................................................2
1-04.01. OverallDimensionsforF H-2 ................................................2
1-04.02. OverallDimensionsforF H-2A-99.............................................3
1-05. RegulatoryListings.........................................................4
1-06. UnitWeights..............................................................4
2. Installati n...............................................5
2-01. Location .................................................................5
2-02. Unpacking................................................................6
2-03. ElectricalRequirements.....................................................6
2-03.01. ElectricalConnections(Overview).............................................7
2-03.02. HoodPowerConnection.....................................................7
2-03.03. Hood and Appliance Interlock Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2-03.04. FireAlarmConnection ......................................................9
2-04. LimitationsandClearances ..................................................9
2-04.01. FryerLimitations ..........................................................9
2-04.02. FryerClearancesforF H-2..................................................10
2-04.03. FryerClearancesforF H-2A-99..............................................11
2-05. Fire uppression ystem...................................................12
2-05.01. Fusible Links and Gas Cartridge Location. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2-05.02. Fire Exinguishing Nozzles and Tank Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2-05.03. ManualPullDiagram.......................................................14
2-06. RestrainingDevice ........................................................15
3. Overview ...............................................17
3-01. FilterChamber ...........................................................18
3-02. ControlPanel ............................................................20
3-03. Accessories(Included).....................................................22
4. Operati n...............................................25
4-01. HoodOperation ..........................................................25
4-02. HoodFiltersandFilterMaintenance ..........................................25
4-02.01. HoodFilterTable..........................................................25

Table Of Contents
iv
4-02.02. BaffleFilterRemoval.......................................................26
4-02.03. BaffleFilterInstallation.....................................................27
4-02.04. BaffleFilterMissing.......................................................28
4-02.05. BaffleFilterCleaningProcedure..............................................28
4-02.06. EACFilterRemoval........................................................28
4-02.07. EACFilterInstallation......................................................29
4-02.08. EACFilter tatus..........................................................29
4-02.09. EACFitlerCleaning........................................................30
4-02.10. CharcoalFilterRemoval ....................................................31
4-02.11. CharcoalFilterInstallation ..................................................31
4-02.12. CharcoalFilterMissing.....................................................32
4-02.13. CharcoalReplacementProcedure ............................................32
4-02.14. UltraVioletLampRemoval..................................................33
4-02.15. UltraVioletLampInstallation ................................................33
4-02.16. UltraVioletLampCleaning..................................................34
4-03. Maintenance.............................................................35
4-03.01. MonthlyInterlockCheck....................................................35
4-03.02. emi-Annual Fire uppression ystem ervicing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
4-03.03. Annual Fire uppression ystem ervicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
4-03.04 AnnualUV ystem ervicing................................................36
4-03.05. Twelve Year uppression ystem ervicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
4-03.06. Maintenanceand erviceLog ...............................................37
5. GeneralH dCleaning ...................................39
5-01. WeeklyCleaning..........................................................39
5-02. QuarterlyCleaning ........................................................39
6. Tr ublesh ting .........................................41
6-01. TroubleshootingProcedures.................................................41
7. PartsList ...............................................43
7-01. Parts Ordering and ervice Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
7-02. VentlessHood-Front......................................................44
7-03. VentlessHood-Rear ......................................................46
Model: FSH-2, FSH-2A-99,
& FSH-2A-99W

v
Safety
Safety Overview
Safety
The instru tions ontained in this manual have been prepared to aid you in learning the proper pro edures
for installing and servi ing your new unit.
Throughout this manual, safety pre autions are identified through the use of the safety alert symbol and
three signal words: DANGER, WARNING, and CAUTION. All safety alert information pre edes the
step(s) to whi h they apply. Suggested, re ommended, or other noteworthy information is identified
through the use of NOTES. Additionally, ertain words are used to indi ate a spe ifi meaning or to add
emphasis.
The following words are used as indi ated throughout the manual:
Shall: understood to be mandatory.
Should: understood to be advisory.
May: understood to be permissive.
Will: indi ates a future event/ ondition to o ur.
•Indi ates an imminently hazardous situation whi h, if not avoided, will result in death or serious injury.
!DANGER
•Indi ates a potentially hazardous situation whi h, if not avoided, ould result in death or serious injury.
!WARNING
•Indi ates a potentially hazardous situation whi h, if not avoided, may result in minor or moderate injury.
Also used to alert against unsafe pra ti es.
!CAUTION
•When used without the safety alert symbol, CAUTION indi ates a potentially hazardous situation whi h,
if not avoided, may result in equipment/property damage, and void the warranty.
CAUTION
NOTE:
•Identifies suggested, re ommended, or other noteworthy information.
or
Used in onjun tion with signal words (DANGER, WARNING, or CAUTION) to alert you of potential per-
sonal injury hazards, immediately pre eding pre autionary measures that pertain to subsequent step(s).
Obey all safety messages that follow this symbol to avoid possible injury or death. Failure to adhere to
safety pre autions identified by the safety alert symbol may also void the warranty.
!!
Model: FSH-2, FSH-2A-99

vi
Safety
•Turn off the unit and unplug the power ord before leaning or performing maintenan e.
•DO NOT hose down the unit’s interior or exterior with water.
•Failure to omply with these DANGER noti es will result in death or serious injury, equipment/property damage,
and void the warranty.
!DANGER
•Internal ultraviolet radiation sour e
•Keep prote tive barrier in pla e.
•Repla e all removable overs or panels after servi ing.
•Interlo ks are intalled to redu e potential for exposure to ex essive ultraviolet radiation. DO NOT attempt to
bypass these interlo ks.
For your safety, please observe the following pre autions when operating or servi ing your Giles equip-
ment. Read the following important safety information to avoid personal injury and/or damage to the
equipment.
•Consult a qualified ele tri ian to ensure that:
•• all ele tri al spe ifi ations and odes are met.
•• ir uit breakers and wiring are of suffi ient rating and gauge.
•The unit must be properly grounded and all ele tri al spe ifi ations must be met during installation.
•Improper installation, adjustment, alteration, servi e or maintenan e ould result in death or serious injury, equip-
ment/property damage, and void the warranty.
•DO NOT use or store flammable liquids, or materials produ ing flammable vapors, in the vi inity of this or any
other applian e!
•Failure to omply with WARNING noti es ould result in death or serious injury and equipment/property damage
and void the warranty.
!WARNING
Specific Safety Precautions
!WARNING
Model: FSH-2, FSH-2A-99

vii
Safety
•The unit must be adequately and properly grounded. Improper grounding may result in electrical shoc .
Always refer to local electrical code to ensure proper grounding of this or any other electrical equipment.
Always consult with an electrician or other qualified service person to ensure brea ers and wiring are of suf-
ficient rating and gauge for the equipment being operated.
•Ensure the unit is positioned in a se ure, safe lo ation.
•Consult an ele tri ian to ensure all ele tri al spe ifi ations have been met and the unit is properly grounded. The
wiring diagram provided with this unit should aid an ele tri ian during installation.
!CAUTION
•The ele troni omponents of the Control Panel are impa t-sensitive. Exer ise are around the Control Panel to
maintain proper operation.
•During leaning of the unit
•• DO NOT steam lean.
•• DO NOT use produ ts ontaining hlorine.
•• DO NOT use abrasive produ ts, steel wool or s ouring pads.
•DO NOT modify, alter or add atta hments to this equipment!
•Failure to omply with these CAUTION noti es may result in equipment/property damage and void the warranty.
CAUTION
NOTE:
•If the rate is damaged upon re eipt, immediately inspe t the unit and notify the arrier of any damage to the
unit.
•To aid the ele tri ian, an ele tri al wiring diagram is provided with the unit. Refer to the wiring diagram during
installation or servi ing.
•Comply with all appropriate state and/or lo al heath regulations regarding the leaning and sanitation of equip-
ment.
•The unit must remain in the upright (verti al) position.
•Exer ise are when removing the wooden rate from around the unit.
•DO NOT operate the unit unless you fully understand the omponents and their intended fun tion (see Se tion
3).
!CAUTION
Model: FSH-2, FSH-2A-99

viii
Safety
Notes:
Model: FSH-2, FSH-2A-99
NOTE:
•Consultation with an HVAC specialist may be required for some installa-
tions to confirm proper room air exchange and the heat load capabilities of
the on site AC system.
•Exhaust ventilation is re ommended for areas in whi h re ir ulating hoods are used. We re ommend
50 CFM per linear foot of hood spa e.
•This amount ould vary based on lo al odes and the site spe ifi installation requirements.

Congratulations on the purchase of your new Giles Free Standing Ventless Hood, Model FSH-2 or FSH-2A-
99 manufactured by Giles Enterprises, Inc., Montgomery, Alabama (USA), hereafter referred to as "Giles".
The Free Standing Ventless Hood is a product of extensive research and testing. Every unit is thoroughly
inspected and tested prior to shipment. roper care and maintenance will ensure years of trouble-free
service.
The Giles Ventless Hood System is used in conjunction with various listed cooking appliances to accom-
plish removal of grease vapors and objectionable odors which may be generated during cooking. The hood
system performs this function through the use of what is commonly referred to as an electronic air clean-
er (EAC). Electronic air cleaners use an electrical charge to remove contaminants from the air as they pass
through the EAC.
To help protect your investment in this equipment, we recommend taking a few moments to familiarize
yourself with the installation, cleaning and maintenance procedures contained in this manual. Read these
instructions before installation and use. Adherence to these recommended procedures minimizes the
potential for costly "down-time" and equipment repairs. lease retain this manual for future reference.
Three Stage Filtration -uses three different filters to remove particulate matter from the air.
Extinguishing System -built into the hood to extinguish an accidental fire from the Fryer installed
underneath the hood.
1. Introduction
1-01. Construction
1-02. Standard Features
All of the unit’s exterior parts are constructed of stainless steel.
1-03. Optional Feature
Ultimate entless: Ultra Violet light in conjunction with Giles patented air filtration system
improves emission cleaning and odor control as well as keeping the unit
free from grease build up.
Interlocking Start System (ILS): In the event of a power interruption, the Hood and the Appliance below
the Hood will not restart after power is restored until attended by an
operator. ILS is required by some cities and/or states. lease check
with your local code officials to see if this system is required.
Model: FSH-2, FSH-2A-99
Introduction
1

2
Introduction
1-04. Specifications
1-04.01. Overall Dimensions for FSH-2
INCHES [MILLIMETERS]
DOCKING OPENING WIDTH “X”
MODEL (LETTER DESIGNATION
FOR OPENING) IN. MM
FSH-2 (A) 24 609.6
FSH-2 (B) 20-1/8 511.2
FSH-2 (C) 18-5/8 473.1
FSH-2 (D) 16-1/8 409.6
FSH-2 (E) 15-5/8 396.9
FSH-2 (F) 15-1/8 384.2
FSH-2 (G) 14-1/8 358.8
FSH-2 (H) 10-1/8 257.2
Model: FSH-2, FSH-2A-99

3
Introduction Model: FSH-2, FSH-2A-99
1-04.02. Overall Dimensions for FSH-2A-99
INCHES [MILLIMETERS]
DOCKING OPENING WIDTH “X”
MODEL (LETTER DESIGNATION
FOR OPENING) IN. MM
FSH-2-99 (A) 24 609.6
FSH-2-99 (B) 20-1/8 511.2
FSH-2-99 (C) 18-5/8 473.1
FSH-2-99 (D) 16-1/8 409.6
FSH-2-99 (E) 15-5/8 396.9
FSH-2-99 (F) 15-1/8 384.2
FSH-2-99 (G) 14-1/8 358.8
FSH-2-99 (H) 10-1/8 257.2

Introduction Model: FSH-2, FSH-2A-99
1-06. Unit Weights
1-05. Regulatory Listings
UL (US and Canada)
NSF
CE
Model
Weights
Crated Uncrated
lb kg lb kg
FSH-2 462 146 327 148
FSH-2A-99 535 243 380 173
4

5
Installation
•DO NOT ODIFY, ALTER OR ADD ATTACH ENTS TO THIS EQUIP ENT
!CAUTION
1. Before unpacking the unit and assembling the unit, using the dimensions and clearances shown in
Section 2-04.03. and 2-04.06, determine the location of the unit.
2. Keep the unit and the surrounding area free and clear from combustible materials.
3. Please provide adequate room for servicing and proper operation of the unit. Also, provide
adequate ventilation in the operating area where necessary.
4. Before operating, make sure the unit is in a secure position and will not move.
This section provides a summary of the procedures necessary for proper installation of your unit. To help pre-
vent personal injury or equipment damage, please ensure the following steps are taken.
2. Installation
2-01. Location
NOTE:
•The decibel level of the hood when operating is approximately 65 dB’s.
Model: FSH-2, FSH-2A-99
NOTE:
•Consultation with an HVAC specialist may be required for some installa-
tions to confirm proper room air exchange and the heat load capabilities of
the on site AC system.
•Exhaust ventilation is recommended for areas in which recirculating hoods are used. We recommend
50 CF per linear foot of hood space.
•This amount could vary based on local codes and the site specific installation requirements.

6
Installation
•Exercise care when lifting or moving the unit.
•Exercise care when removing the wooden crating from around the unit.
•Failure to comply with these CAUTION notices may result in minor or moderate injury, equip-
ment/property damage, and void the warranty.
!CAUTION
1. Carefully cut and remove the plastic shipping wrap and the strapping.
2. Using appropriate tools, carefully remove the wooden crating from around the unit.
3. Carefully remove the unit from the shipping platform. The FSH-2 or FSH-2A-99 is extremely heavy,
see Section 1-03.04. for unit weights. Great care should be taken when lifting or moving the unit to
prevent personal injury or equipment damage.
NOTE:
•If the crate is damaged, immediately inspect the unit and notify the carrier of any damage to the
unit.
2-02. Unpacking
2-03. Electrical Requirements
Hood Electrical Requirements (Hood Only)
Unit Voltage Hz Phase Amps Breaker
FSH-2 208-240 60 1 3 10
FSH-2A-99 208-240 60 1 3 10
•Consult a qualified electrician to ensure all electrical specifications have been met.
•The unit must be adequately and properly grounded. Improper grounding may result in electrical
shock. Always refer to local electrical code to ensure proper grounding of this or any other electri-
cal equipment. Always consult with an electrician or other qualified service person to ensure
breakers and wiring are of sufficient rating and gauge for the equipment being powered.
• I mproper installation, adjustment, alteration, service or maintenance could result in death or serious injury, equip-
ment or property damage, and void the warranty.
!WARNING
The unit will arrive enclosed by a wooden crate. The Hood is secured to a wooden platform by means of
high-tensile strength strapping and wrapped with stretch-wrap.
Model: FSH-2, FSH-2A-99

7
Installation
2-03.01. Electrical Connections (Overview)
Connect Hood Power:
1. Install appropriate Circuit Breakers in Hood Supply Power Box ( ain Breaker Box). See Section 2-03.
for required Circuit Breakers.
2. Remove Cover on Service Entrance Box and run appropriate size conduit and wire from the Service
Entrance Box to the Hood Supply Power box ( ain Breaker Box). Allow enough conduit and wire so
the unit can be accessed for cleaning and servicing.
3. ake all appropiate connections.
4. Reinstall Service Entrance Box Cover.
2-03.02. Hood Power Connection
Fire Alarm Tie-In Box
Interlock Tie-In Box
Service Entrance
Box
Connection to
Appliance
Model: FSH-2, FSH-2A-99

8
Installation
Interlock Hood to Appliance:
1. Remove Cover on Interlock Tie-In Box and run appropriate size conduit and wire from the Interlock
Tie-In Box to a Hood and Appliance Connection Box (Supplied by Customer). Allow enough conduit
and wire so the Hood can be accessed for cleaning and servicing.
2. ake appropiate connections. See Diagram below.
3. Reinstall Interlock Tie-In Box Cover.
2-03.03. Hood and Appliance Interlock Connection
NOTE:
•If not using the ILS option, the Hood will continue to run and the Appliance will turn off when:
•Any Filter becomes excessively dirty, not allowing proper air flow through the Hood.
•Any Filter is missing or not installed correctly.
•The Fire Extinguisher System is activated.
•If using the ILS option, the Hood and Appliance will turn off when:
•Any Filter becomes excessively dirty, not allowing proper air flow through the Hood.
•Any Filter is missing or not installed correctly.
•The Fire Extinguisher System is activated.
This interlock circuit will disable power to the Appliance installed under the Hood if any of the following
occurs:
• Any Filter becomes excessively dirty, not allowing proper air flow through the Hood.
• Any Filter is missing or not installed correctly
• The Fire Extinguisher System is activated.
Model: FSH-2, FSH-2A-99

9
Installation
2-03.04. Fire Alarm Connection
This connection will send a signal the Facility Fire Alarm System in the event that the Hood Fire
Extinguisher System is activated.
Fire Alarm Connection:
1. Remove Cover on Fire Alarm Tie-In Box and run appropriate size conduit and wire from the Box to
the Facility Fire Alarm System. Allow enough conduit and wire so the Hood can be accessed for
cleaning and servicing.
2. ake appropiate connections.
3. Reinstall Fire Alarm Tie-In Box Cover.
Hood ax. kW Input ax. Shortening
Capacity (lbs)
ax Cooking Surface
(per Fryer)
FSH-2 20 110 380 Sq. In.
FSH-2A-99 20 110 380 Sq. In.
2-04.01. Fryer Limitations
•The Hoods are design for Electric Fryers Only!!! DO NOT USE ANY GAS APPLIANCES UNDER THE FSH-2
or FSH-2A-99!!
!WARNING
2-04. Limitations and Clearances
This section describes various limitations for appliances that can be placed underneath the hoods. ONLY
electrically heated appliances, which meet these limitations and clearances are approved for use under
these hoods. Gas appliances or appliances other than the types stated are not approved.
Model: FSH-2, FSH-2A-99

10
Installation
Model: FSH-2, FSH-2A-99
2-04.02. Fryer Clearances for FSH-2
Fusible Link
Fry Vat
DOCKING OPENING WIDTH “X”
ODEL (LETTER DESIGNATION
FOR OPENING) INCHES ILLI ETERS
FSH-2 (A) 24 609.6
FSH-2 (B) 20-1/8 511.2
FSH-2 (C) 18-5/8 473.1
FSH-2 (D) 16-1/8 409.6
FSH-2 (E) 15-5/8 396.9
FSH-2 (F) 15-1/8 384.2
FSH-2 (G) 14-1/8 358.8
FSH-2 (H) 10-1/8 257.2
Fryer Only
INCHES [ ILLI ETERS]