Gira 0867 00 User manual

Radio repeater
Order No. : 0867 00
Operating instructions
1 Safety instructions
Electrical equipment may only be installed and fitted by electrically skilled persons.
Serious injuries, fire or property damage possible. Please read and follow manual fully.
The radio communication takes place via a non-exclusively available transmission path,
and is therefore not suitable for safety-related applications, such as emergency stop and
emergency call.
Do not shorten, extend or strip the antenna. Device can be damaged.
These instructions are an integral part of the product, and must remain with the end
customer.
2 Device components
Figure 1
(1) Repeater
(2) LED, red
(3) LED, green
(4) Housing lid
(5) Screws
3 Function
System information
By statute, the transmitting power, the reception characteristics and the antenna cannot be
changed.
The range of a radio system from the transmitter to the receiver depends on various
circumstances.
The range of the system can be optimised by selecting the optimal installation location, taking
into account the structural circumstances.
1/5
82530522 24.10.2016
Radio repeater
Radio bus system

Figure 2: Reduced range due to structural obstacles
Example of penetration of various materials:
Material Penetration
Wood, Plaster, Plasterboard approx. 90%
Brick, Chipboard approx. 70%
Reinforced concrete approx. 30%
Metal, Metal grid approx. 10%
Rain, Snow approx. 1-40%
Intended use
- Device for receiving and repeating radio telegrams
- Extending the range of radio transmitters
- Surface-mounted
Product characteristics
Figure 3
- Max. distance between transmitter and repeater and repeater and receiver 100 m
82530522 24.10.2016 2/5
Radio bus system
Radio repeater

- Several repeaters can be installed in a single system, e.g. two transmitters A + B transmit
to a single actuator C (Figure 3)
- Indication of the operating states via 2 LEDs:
Red LED lights up briefly: receiving a telegram
Green and red LEDs light up briefly: a taught telegram is being relayed
Red LED flashes continuously: repeater is in programming mode
Figure 4
iCascading of repeaters is not possible, i.e. telegrams transmitted by a repeater will not be
repeated by another repeater (Figure 4).
4 Information for electrically skilled persons
4.1 Fitting and electrical connection
Mounting and connecting the device
DANGER!
Electrical shock when live parts are touched.
Electrical shocks can be fatal.
Before working on the device, disconnect the power supply and cover up live
parts in the working environment.
Protection rating IP 54 or IP 20, depending on the type of installation:
IP 54 = fixed connection with NYM-J 3x1.5 cable and antenna not routed out of the device.
IP 20 = connection with supplied mains cable and/or antenna routed out of the device.
Maintain a distance of at least 0.5 m from metal surfaces and electrical devices, e.g. microwave
ovens, hi-fi and TV systems, electronic ballasts or transformers.
Mount repeater as close as possible to the middle of the desired transmission path.
oSlacken screws (5) and remove housing lid (4).
The TOP label on the rear of the housing has to be at the top.
If the repeater is intended to amplify the radio telegrams of a stationary transmitter, the teaching
procedure for the radio transmitter should be performed before installation (see Commissioning
chapter).
82530522 24.10.2016 3/5
Radio bus system
Radio repeater

Figure 5
oFasten repeater with 2 screws (6).
oBreak out cable entry (10) and insert mains cable (9).
oConnect mains cable to the repeater.
oTeach transmitter into repeater (see Commissioning chapter).
oFasten housing lid with screws.
Routing the antenna out of the housing
iOnly permitted with protection rating IP 20.
If the radio reception capability of the repeater is not sufficient, it can be improved by routing out
the antenna that is rolled up in the device.
oSlacken screws (5) and remove housing lid (4).
oBreak out cable entry (7).
oRoute antenna (8) out.
oFasten housing lid with screws.
4.2 Commissioning
Teaching a radio transmitter
In order for the repeater to transmit the radio telegram of a transmitter, this transmitter has to be
taught into the repeater.
While a transmitter is being taught the range of the repeater is reduced to approx. 5 m. The
distance between the repeater and the transmitter being taught should therefore be between
0.5 m and 5 m.
oTurn Prog switch (11) to the ON position (Figure 5).
The red Prog LED (2) flashes (Figure 1).
oTrigger teach telegram on radio transmitter (see instructions for radio transmitter).
The radio transmitter has been taught. The green and red LEDs light up as an
acknowledgement.
iWhen the radio transmitter is taught, all of the channels that are present, the All On, All Off
and the light scene buttons are also taught.
oTurn Prog switch (11) to the OFF position.
Both LEDs go out.
Deleting radio transmitters
oTeach-in again the radio transmitter to be deleted.
82530522 24.10.2016 4/5
Radio bus system
Radio repeater

The red LED lights up to confirm that a radio transmitter has been deleted.
5 Appendix
5.1 Technical data
Rated voltage AC 230V~
Mains frequency 50 / 60Hz
Ambient temperature -20 ... +55°C
Degree of protection IP 20 / IP 54
Connecting cable 1.5m
Dimensions W×H×D 110×94×38 mm
Teachable radio transmitter max. 60
Radio frequency 433.05MHz ... 434.79MHz
Receiver category 2
Transmitting range in free field typ. 100m
Transmission capacity < 10mW
5.2 Troubleshooting
Radio receiver does not respond, or only sometimes.
Cause 1: Radio range exceeded. Structural obstacles reduce the range.
Check routing of antenna. Laying the antenna stretched out increases the range (see
chapter Routing the antenna out of the housing).
Cause 2: Incorrect switch setting Prog (11).
Turn Prog switch to the OFF position.
5.3 Conformity
Gira Giersiepen GmbH & Co. KG hereby declares that the radio system type
Order No. 0867 00
corresponds to the directive 2014/53/EU. You can find the full article number on the device. The
complete text of the EU Declaration of Conformity is available under the Internet address:
www.gira.de/konformitaet
5.4 Warranty
The warranty follows about the specialty store in between the legal framework as provided for
by law
Please submit or send faulty devices postage paid together with an error description to your
responsible salesperson (specialist trade/installation company/electrical specialist trade). They
will forward the devices to the Gira Service Center.
Gira
Giersiepen GmbH & Co. KG
Elektro-Installations-
Systeme
Industriegebiet Mermbach
Dahlienstraße
42477 Radevormwald
Postfach 12 20
42461 Radevormwald
Deutschland
Tel [phone] - 602-0
Fax [phone] - 602-191
www.gira.de
[email protected]
82530522 24.10.2016 5/5
Radio bus system
Radio repeater