GKOLED GKOFD05 User manual
Installation Guide
LED FLOOD LIGHT
Installation Guide
WARNING
— To prevent personal injury or product damage only licensed electricians should install.
— To avoid electric shock or component damage disconnect power before attempting installation or servicing.
— This product must be installed in accordance with the national electric code (NEC) and all applicable federal, state and local electric codes and safety standards.
— Disconnect product and allow cooling prior to servicing.
— Any alteration or modification of this product is expressly forbidden as it may cause serious personal injury, death, property damage and/or product malfunction.
— To prevent product malfunction and/or electrical shock this product must be properly grounded.
— This luminaire is designed to operate in ambient temperatures ranging from -40°C to 45°C.
— This product must be installed in accordance with the applicable installation code by a Person familiar with the construction and operation of the product and
the hazards involved.
— In 75°c supply conductors.
— Slipfitter Mounted with PHOTOCELL function elevation angle should not exceed 15 degrees
PLEASE READ ALL INSTRUCTIONS BEFORE ATTEMPTING INSTALLATION
TROUBLESHOOTING
1.
to wiring directions.
2.
3. Be sure the photocell, if used, is functioning properly.
Universal voltage driver permits operation at 120V to 277VAC,
60 Hz except xtures factory ordered with a 347V photocell (P3)
or 480V photocell (P4) or 120-277V photocell(P0).
PHOTOCELL INSTALLATION
1. Install photocell and wire as per diagram.
2. Use photocell rated for your supply voltage.
Trunnion
1. Mount xture onto surface using the hole
pattern provided on the trunnion bracket.
2. Loosen center bolts and set screw.
3. Rotate xture to desired aiming position
and tighten center bolts.
4. Make wiring connection as per wire
diagram below.
Wall Mount
Black
White Neutral
Green/Yellow Green
Ground
Line
Purple
DIM+
Gray
DIM-
BLACK
BLACKBLACK
INPUT
LAMPLOAD
RED
PHOTOCONTROL
WHITE
WHITEWHITE
Sliptter
1. Connect the wires to L / N / GND
2. Remove the cover and adjust the bracket to the desired angle
3. Install the bracket on the pole and x it with screws
Side plate
5/16’’*1.02(inch) UNC Screws
Twisted photocell (optional)
M8*20(mm) Screws
PM4*12(mm) Screws
5/16’’*1.02(inch) UNC Screws
Twisted photocell (optional)
PM4*8(mm) Screws
Motion Sensor (optional)
Back plate
Side plate
1/2’’1.46(inch) UNC Screws
PM4*12(mm) Screws
KM4*10(mm) Screws
OPEN
1. Remove the side plate by loosen the screws.
2. Fix the back plate onto the arm bracket with
screws provided.
3. Use the metal template provided to locate
footprint on the wall to drill the holes, then
x the bracket on the wall with screws.
4. Route the power cord into wall mount bracket,
slide the xture onto the mounting bracket, then
tighten bottom screws.
5. Make wiring connection inside of bracket and
replace the side plate with screws.
78mm(3.07in.)
76.2mm(3in.)
114.3mm(4.5in.)
15.88mm(0.625in.)
Ø21mm(0.827in.)
(Figure 1)
(Figure 2)
(Figure 3)
ACCESSORY LIST
Slipfitter Mount
Mounting Type Specifications Quantity
Adjustable slipfitter 1
120-277V 3-Pin
3-Pin receptacle
PM4 x 8 Stainless Steel, Round Flat bottom Bolt 2
120-277V 0-10V Bi-level
1
1
1
Wall mount
Others
Accessory
Slipfitter
# 1/2'' x 1.46'' Stainless Steel Hexagon head bolt 2Bolt
KM4 x 10'' Stainless Steel flat head bolt 4Bolt
20.3 x 15.2 x 0.5cm Steel Plate 1Wall Mount Plate
20.3 x 15.2 x 0.1cm Aluminum alloy plate 1Wall Mount Template
19.9 x 17.7 x 9cm Square pole mount arm 1Pole Mout Arm
Twist-lock photocell
Receptacle
Bolt
Occupancy Sensor
①② ③
④④
⑤
⑤
①
②
CM10x25-SS Stainless steel hexagon socket head cap bolt 2Bolt
MAL02300TR-L363W68H363T4 bracket 1Bracket
①
①
②
②
③
Trunnion Mount
Other GKOLED Floodlight manuals
