GKOLED GKOFD05150W27V50KBDB77 User manual

Installation Guide
LED FLOOD LIGHT
Installation Guide
WARNING
— To prevent personal injury or product damage only licensed electricians should install.
— To avoid electric shock or component damage disconnect power before attempting installation or servicing.
— This product must be installed in accordance with the national electric code (NEC) and all applicable federal, state and local electric codes and safety standards.
— Disconnect product and allow cooling prior to servicing.
— Any alteration or modification of this product is expressly forbidden as it may cause serious personal injury, death, property damage and/or product malfunction.
— To prevent product malfunction and/or electrical shock this product must be properly grounded.
— This luminaire is designed to operate in ambient temperatures ranging from -40°C to 45°C and to be horizontally mounted with the LEDs facing down.
— This product must be installed in accordance with the applicable installation code by a Person familiar with the construction and operation of the product and
the hazards involved.
— MIN 75°C SUPPLY CONDUCTORS
— CONSULT A QUALIFIED ELECTRICIAN TO ENSURE CORRECT BRANCH CIRCUIT CONDUCTOR
— CAUTION - RISK OF FIRE
— While installing photocell on flood light, the horizontal elevation angle should not exceed 15°
— This product is not available for several special environments, such as places with corrosive gas liquids or high pressure water vapor
PLEASE READ ALL INSTRUCTIONS BEFORE ATTEMPTING INSTALLATION
Sliptter
Wall Mount
BLACK
BLACKBLACK
INPUT
LAMPLOAD
RED
PHOTOCONTROL
MOTION SENSOR
WHITE
WHITEWHITE
1. Connect the wires to L / N / GND
2. Remove the cover and adjust the bracket to the desired angle
3. Install the bracket on the pole and x it with screws
(Figure 1)
Side plate
5/16’’*1.02(inch) UNC Screws
Twisted photocell (optional)
M8*20(mm) Screws
PM4*12(mm) Screws
1. Remove the side plate by loosen the screws.
2. Fix the back plate onto the arm bracket with screws provided.
3. Use the metal template provided to locate footprint on the wall
to drill the holes, then x the bracket on the wall with screws.
4. Route the power cord into wall mount bracket, slide the xture
onto the mounting bracket, then tighten bottom screws.
5. Make wiring connection inside of bracket and replace the
side plate with screws.
(Figure 2)
Twisted photocell (optional)
Motion Sensor (optional)
Trunnion/Yoke
1. Mount xture onto surface using the hole
pattern provided on the trunnion bracket.
2. Loosen center bolts and set screw.
3. Rotate xture to desired aiming position
and tighten center bolts.
4. Make wiring connection as per wire
diagram below.
(Figure 3)
（250W-300W Trunnion）
（Yoke 150W-200W）
78mm(3.07in.)
76.2mm(3in.)
114.3mm(4.5in.)
15.88mm(0.625in.)
Ø21mm(0.83in.)
Note:Two dimming wire in the driver box
Black
White Neutral
Green/Yellow Green
Ground
Line
Purple
Gray
Wire Connection
5/16’’*1.02(inch)
UNC Screws
PM4*12(mm)
Screws
KM4*10(mm)
Screws
Steel plate
OPEN
Side plate
Back plate
1/2’’1.46(inch)
UNC Screws
EVA Gasket
80mm(3.15in.)
78mm(3.07in.)
95mm(3.74in.)
51mm(2in.)
Ø14mm(0.55in.)
Ø22mm(0.86in.)
Ø11mm(0.43in.)

ACCESSORY LIST
CM10x25-SS Stainless steel hexagon socket head cap bolt 2Bolt
AL30TR-L338W68H313T4 bracket 1Bracket
①
①
②
②
Trunnion mount
Slipfitter mount
Mounting Type Specifications Quantity
Adjustable slipfitter 1
L129.5W60H88T3 upper bracket + L138W60H88T3 lower bracket
+ L116W48H70 bracket 1
Accessory
Slipfitter
Bracket
Yoke mount
# 1/2'' x 1.46'' Stainless Steel Hexagon head bolt 2Bolt
KM4 x 10'' Stainless Steel flat head bolt 4Bolt
20.3 x 15.2 x 0.5cm Steel Plate 1Wall Mount Plate
18.8 x 14.4 x 0.05cm Back Plate 1Wall Mount Template
19.9 x 17.7 x 9cm Square pole mount arm 1Pole Mount Arm
120-277V 3-Pin
3-Pin receptacle
PM4 x 8 Stainless Steel, Round Flat bottom Bolt 2
120-277V 0-10V Bi-level
1
1
1
Others
Twist-lock photocell
Receptacle
Bolt
Occupancy Sensor
⑤
⑥
①
②
③
L119W119H3,40°EVA Gasket 1EVA Gasket
④
Wall mount
① ② ③④
⑤ ⑥