Glacier bay VDR2522A1 User manual

,Monday - Friday
SKU#
Model# VDR2522A1 /
VDR3322A1 /
VDR3322A0
V1-TD-3

Topmount Installation
Undermount Installation
Care and Cleaning
Service Parts
Package Contents
Hardware Included 3
4
8
12
15
16

1-855-HD-GLACIER or visit www.HomeDepot.com/GLACIERBAY.
/under
(NOT INCIUDED)
HARDWARE REQUIRED (NOT INCIUDED) HARDWARE REQUIRED (NOT INCIUDED)
HARDWARE REQUIRED (NOT INCIUDED)
HARDWARE REQUIRED
Undermount CIips (10 recommended )
These screws can be installed with power tools.
Hardware not shown to actual size.

SKU# Model# Bowls Picture
VDR2522A1
VDR3322A1
VDR3322A0
Single
Single
Double
NOTE: The manual only displays the assembly for double bowl
sink, but the assembly instruction is including but not limited to
below SKU & configuration
4
NOTE: Please matching your purchased product for below pages

Part Description Quantity
L
Faucet
Topmount/Undermount template
5

Part Description Quantity
Faucet
Topmount/Undermount template
1
1
1
6
L

Part Description Quantity
Faucet
2
2
2
2
2
2
2
2
2
Topmount/Undermount template
7
L

.
.
Installing the strainer assembly
Topmount Installation
Installation Types
8

4
Shut off the water supply.
Insert the faucet assembly (L) through the hole in the sink.
5Securing the faucet assemblyInstalling the faucet assembly
L
CAUTION: Always shut off the water supply before
removing an existing faucet or replacing any part of a
faucet. Open the faucet handle to relieve water pressure
and ensure that the water is completely shut off.
Topmount Installation (continued)
9
21
Sink
Push
up
21
1 1
Push
up 21
2
3
3
Sink
21
Sink
Continue to push up
and turn clockwise
to tighten
From underneath the sink, secure the faucet assembly
to the sink with the FastmountTM system (21). Push
the FastmountTM system (21) up over the threads until
it stops against the bottom of the sink, then hand turn
(clockwise) to tighten.
Attaching the quick connector
to the receiving block
6 7
9
18
Weight
here
Weight
here
20 20
19
19
Installing the weight
Install the weight clip (20) at the point of the hose marking
"weight here”.
Insert the weight (19) onto the clip (20) by sliding it down
onto the clip (20).
Push the quick connector (18) firmly upward and attach it
to the receiving block (9). Pull down moderately to ensure
the connection has been made.

89Making the water supply connections
Thread the nut (1) on the supply line onto the outlet of the
water supply valve (2) and tighten with a wrench. Do not
overtighten.
NOTE: The hot side inlet tube is indicated by a label. Avoid
twisting wires together or placing the wires close to each
other and damaging.
1
2
Flushing and checking for leaks
Pull the hose assembly out of the spout and remove
the spray head by unscrewing it from the hose in a
counterclockwise direction. Be sure to hold the end of
the hose down into the sink and turn the faucet to
the warm position where it mixes hot and cold water.
Flush the water lines for one minute. This flushes away
any debris that could cause damage to internal parts.
Check for leaks.
Re-tighten any connections if necessary, but do not
overtighten. Reinstall the spray head by hand tightening
it back onto the spray hose in a clockwise direction.
IMPORTANT: After installation is completed, turn on the
hot and cold water supplies. Check for leaks. Do not lose
the gasket (1) in the hose.
1
Topmount Installation (continued)
These screws can be installed with power tools.
10
10