Glacier bay VDR2522A1 User manual

, Monday-Friday
SKU#1002760068
Model#VDR2522A1

12

HD-GLACIER or visit www.HomeDepot.com/GLACIERBAY.
/unde
This sink is a topmount r
10
These screws can be installed with power tools.
Hardware not shown to actual size.
Under mount clips not included. If you are installing this sink as an
under mount, please contact a professional installer or contact us
at 1-855-HD-GLACIER to determine the type of clip needed.
NOTE:

Q
R
S
Part Description Quantity
N
O
Mounting nut
Soap assembly
Soap pump
L
N
M
O
P
T
FastMount™
Faucet assembly
Weight
Quick connector
Weight clip
Q
R
S
T
Topmount/Undermount template

.
.
Installing the strainer assembly
Topmount Installation
Installation Types

4
Shut off the water supply.
Insert the faucet body (L) through the hole in the
sink.
5
Securing the faucet assembly
From underneath the sink, secure the faucet
assembly to the sink with the FastMount™
system (M). Push the FastMount™ system (M)
up over the threads until it stops against the
bottom of the sink, then hand turn (clockwise)
to tighten (Fig 1).
Installing the faucet assembly
Sink
Sink
Push
up
Screw
Fig 1
L
CAUTION: Always shut off the water supply before
removing an existing faucet or replacing any part of a
faucet. Open the faucet handle to relieve water pressure
and ensure that the water is completely shut off.
7
Installing the weight
Insert the weight (O) onto the clip (P) by sliding
it down onto the clip (P).
Install the weight clip (P) at the point of the
hose marking “weight here”.
6
Attaching the quick connector
to the receiving block
Push the quick connector (N) firmly upward and
attach it to the receiving block (1). Pull down
moderately to ensure the connection has been
made.
1
N
Weight
here
Weight
here
Topmount Installation (continued)

8Installing the soap dispenser
From under the sink, screw the soap dispenser (T) onto the
soap assembly (O) shank. Insert the soap pump (Q) down
into the soap assembly (O).
Insert the soap assembly (O) through the selected hole
in the sink. Secure the soap assembly (O) to the sink with
the soap dispenser mounting nut (S).
9
Making the water supply connections
Thread the nut (1) on the supply line onto the outlet of the
water supply valve (2) and tighten with a wrench. Do not
overtighten.
NOTE: The hot side inlet tube is indicated by a label. Avoid
twisting wires together or placing the wires close to each
other and damaging.
1
2
Q
O
S
T
Flushing and checking for leaks
Pull the hose assembly out of the spout and remove
the spray head by unscrewing it from the hose in a
counterclockwise direction. Be sure to hold the end of
the hose down into the sink and turn the faucet to
the warm position where it mixes hot and cold water.
Flush the water lines for one minute. This flushes away
any debris that could cause damage to internal parts.
Check for leaks.
Re-tighten any connections if necessary, but do not
overtighten. Reinstall the spray head by hand tightening
it back onto the spray hose in a clockwise direction.
IMPORTANT: After installation is completed, turn on the
hot and cold water supplies. Check for leaks. Do not lose
the gasket (1) in the hose.
11
Removing the quick connector
If it is necessary to remove the quick connector (1),
squeeze the tabs (2) on the quick connector and then
pull down to disconnect.
1
Pull
down
Squeeze
1
1
2
Topmount Installation (continued)

Topmount
These screws can be installed with power tools.

When you choose undermount style installation, please do not pull out the installation rail shown in this illustration.
This will cause the sink to be damaged beyond repair.It is strongly recommended that you use a professional installer is you choose
the undermount installation.
Undermount Installation
HOMEDEPOT.COM/GLACIERBAY
WARNING
：
Under mount clips not included. If you are installing this sink as an
under mount, please contact a professional installer or contact us
at 1-855-HD-GLACIER to determine the type of clip needed.
NOTE:

the sink accessories to the sink before installing
the sink to the cabinet.
step 3.
(not included).
HOMEDEPOT.COM/GLACIERBAY
Undermount Installation (continued)
Place the mounting clips (not included) as shown in the attched template and mark the centers of the clip on the countertop.
Installing the accessories to the sink
Attaching the mounting clips (not included)
Under mount clips not included. If you are installing this sink as an
under mount, please contact a professional installer or contact us
at 1-855-HD-GLACIER to determine the type of clip needed.
NOTE:
Under mount clips not included. If you are installing this sink as an
under mount, please contact a professional installer or contact us
at 1-855-HD-GLACIER to determine the type of clip needed.
NOTE: