GlammFire Crea7ion Plus User manual

Maintenance Technical Manual
Burner Crea7ion Evo Plus Fire Round

GlammFire. PAG./2
Dear Partner, first of all congratulations for being part of the GlammFire family.
Like all equipment, the Crea7ion Evo requires preventive maintenance in order to avoid the need for
corrective maintenance.
This intervention must be annual and the instructions in this manual must be followed step by step.

GlammFire. PAG./3
ÍNDICE
1—Limpeza de zona de combustão 5
2—Limpeza de componentes 7
2.1—Sensores e termopar 7
2.2—Tubo do ar 8
2.3—Limpeza de locais técnicos 9
2.4—Limpeza de filtro 10
2.4.2—Filtro interno 10

Before any kind of intervention on the burner, please read this Instructions Manual carefully. It contains important
instructions that should be followed properly in order to ensure good use and durability.
All warnings and notices submitted must be respected. Save this manual for future reference.
This Instructions Manual is subject to change without previous notice.
GlammFire. PAG./4
The device should be put into operation at least once a month for five minutes, in the case
of little use.
Every device must go through preventive maintenance periodically to avoid the need for
corrective interventions, which can be expensive and unsuccessful.
Therefore, it is extremely important to perform preventive interventions after the months of
greater use of the device. In case of regular use without interruption this intervention
should be annual.
This manual will identify the intervention points as well as the preventive actions to be
taken.

GlammFire. PAG./5
1—Combustion zone cleaning
The repeated Bioethanol combustion leaves residues in the burning area which must be properly cleaned.
Using a soft-bristled brush, soak it in Bioetha-
nol and clean the whole combustion zone.
Remove the ring from the combustion zone and clean it in the same way.

GlammFire. PAG./6
NOTE:
During the cleaning of the combustion zone, it is necessary precaution not to touch the resis-
tance. If this warning is not taken into account, it is possible that the resistance will break,
disabling it.
!
!

GlammFire. PAG./7
2—Components cleaning
All the components of the combustion zone must be cleaned, except the resistance as mentioned before.
2.1—Sensors and thermocouple
Using a soft-bristled brush soaked in Bioethanol, proceed to the cleaning of the sensors and thermocouple.
SENSORS
THERMOCOUPLE

GlammFire. PAG./8
2.2—Air tube
Using a soft-bristled brush soaked in Bioethanol, proceed to the cleaning of the air tube.
AIR TUBE

GlammFire. PAG./9
2.3—Cleaning of the technical points
There are two technical points in the combustion zone that must be cleaned to guarantee its functionality. Both places
are immediately below the two sensors of the combustion zone.
Note: After cleaning the combustion zone, replace the ring properly cleaned.

GlammFire. PAG./10
2.4—Filters cleaning
2.4.1—Internal filter
On the sideline of the safety box, open the side lid by loosening the identified screws.
Lossen screws
To loosen the identified screws, use a 2.5 mm hex key.

GlammFire. PAG./11
Inside the safety box of the burner, identify the filter tied by a serrated clamp.
Cut the clamp carefully.
Carefully, pull the filter out of the burner.

GlammFire. PAG./12
Put a cloth or absorbent paper in the place, remove the filter by removing the silicone tube at its ends.
Use the cloth to absorb the possible ethanol spillage in the tubing or filter.

GlammFire. PAG./13

GlammFire. PAG./14
Unscrew the filter and check it for residues. With or without residues, clean it with tap water.
When the filter is clean, screw it back and perform the reverse process until the side lid is closed.
Note:
When cleaning the filter, check the condition of the seal in order to verify that there are no
leakages.
Be very careful when tightening the filter to avoid damaging it, causing subsequent leakage of
ethanol.
This must be carried out strictly when handling and after the appliance has been put into
operation.
!

GlammFire. PAG./15
GlammFire is always concerned with the environment. This is reflected by the projection of their products and their
packaging. Focusing on the reduction of energy consumption, raw materials, natural resources and quantity of waste
generated, GlammFire follows the policy of the 4R's (Reduce, Reuse, Recycle and Recover). Thus GlammFire has in
mind the use of long lasting products as well as reusable and recyclable products.
GlammFire recommends reusing the GlammFire’s packaging separately and deposit plastic, paper, cardboard and
glass in the appropriate collection point.
"In nature nothing is created, nothing is lost, everything is transformed."
Antoine Laurent de Lavoisier
GlammFire fireplaces are manufactured under the strict Standard of the world recognized ISO 9001:2008 (TUV)
Quality Assurance Certificate.
GlammFire products are designed with superior components and materials, assembled by trained craftsmen who take
great pride in their work.
Once assembled the complete fireplace is thoroughly inspected by a qualified technician before packaging to ensure
that you, the customer, receive the quality product that you expect from GlammFire.

PT12309-A-EN
Recuperadores Pachinha Lda.
Zona Industrial da Lagoa, Lote G1
4950-850 CORTES - MONÇÃO PORTUGAL
Tel[phone]
Fax[phone]
[email protected]om
www.glammfire.com