glamour GHDSV-1402 User manual

SCREWDRIVER HAMMER
SELF-PREPARED TOOLS: Tools below are NOT included in package.
Read instruction carefully . See Furniture Parts list and Hardware List for guidance . Be sure you have all parts before you start assembling .
Place and assemble furniture on a clean flat soft surface , such as carpet or rug to pervent being scratched .
Before you begin, please follow assembly instructions carefully, then follow them step by step.
Reminder:
Please ensure that all surfaces and edges with colours/laminations are facing forward/outward.
1
2
PART LIST
TOP PANEL 1 PC MINI FIX
4
SIDE PANEL (L)
6
SIDE PANEL (R)
7
8
QTY
1 PC
1 PC
31 PC
51 PC
2 PCS
6 PCS
HARDWARE
A
B
C
D
E
F
G
14 PCS
M3.5 X 16MM C.B SCREW 24 PCS
ALLEN KEY M4 1 PC
BOTTOM PANEL
H
I
J
K
M6 X 5OMM
CSK CAP WOOD SCREW 6 PCS
A1 A2 A3
M8 X 30MM WOOD DOWEL 20 PCS
9
10
11 2 PCS
2 PCS
BACK PANEL 1 PC
5/8 NAIL 40 PCS
M4 X 32MM C.B SCREW 4 PCS
MODEL : ASSEMBLY INSTRUCTIONS PAGE: /5
1
SHELF PANEL
12 L
M
SOFT CLOSING 7/8 HINGES 4 PCS
METAL SHELF SUPPORT 24 PCS
WOOD HANDLE (SMALL) 2 PCS
SPRING WASHER M6
FLAT WASHER M6
8 PCS
8 PCS
8 PCS
LEG (R)
LEG (L)
2 PCS
J
MIDDLE PANEL
DOOR PANEL (R)
JCBC SCREW M6 X 40MM
DOOR PANEL (L) 1 PC
77
7
7
77
6
6
5
3
4
1
910
11 11
8
CENTER PANEL
12
12
2
N
TIPPING PACK
2 SETS
N1
N2
N3
N4 N5
POWER DRILL
GHDSV-1402

STEP 1 STEP 2
STEP 3 STEP 4
MODEL : ASSEMBLY INSTRUCTIONS PAGE: /5
2
SCREWDRIVER
REQUIRED
- Insert hardware A2 onto panel (1).
(Repeat 8 times.)
- Insert hardware A2 onto panel (5).
(Repeat 2 times.)
x8
PRESS
B
SCREWDRIVER
REQUIRED
- Insert hardware A1 onto panel (3), (4) and (5).
(Repeat 6 times.)
- Insert hardware A2 onto panel (3), (4) and (5).
(Repeat 6 times.)
- Insert hardware B onto panel (3), (4) and (5).
(Repeat 12 times.)
* Ensure the arrows on hardware A1 point towards mounting positions.
PRESS
A1
x6
A2
x6
ROTATE
x12
PRESS
B
- Attach panel (6) to panel (3), (4) and (5).
- Insert all hardware A2 into A1.
- Rotate all A1 until tight.
- Apply A3 onto all A1.
(Repeat 8 times.)
OR
HARDWARE F
SCREWDRIVER
REQUIRED
* In this step hardware A1, A2 and B are pre-inserted.
x8
PRESS
ROTATE
Section View
x8
A3
A1 A2
1
5
Panel (5) left face
A2
x8
ROTATE
5
Panel (5) right face
3
4
- Insert hardware A1 onto panel (6).
(Repeat 8 times.)
- Insert hardware B onto panel (6).
(Repeat 8 times.)
* Ensure the arrows on hardware A1 point towards mounting positions.
6
6
PRESS
A1
x4
x4
A1
PRESS
6
6
4
5
3
GHDSV-1402

STEP 5 STEP 6
STEP 7 STEP 8
MODEL : ASSEMBLY INSTRUCTIONS PAGE: /5
3
Connect panel (2) to panel (3), (4) and (5) by using hardware C and F.
(Repeat 6 times.)
ROTATE
x6
C
F
* In this step hardware B are pre-inserted.
x8
ROTATE
F
K
L
M
Assemble part 11 and 12 into panel (2) by using hardware F, K, L and M.
(Repeat 8 times.)
HAMMER
REQUIRED
Assemble panel (8) to entire body with hardware G.
(Repeat 40 times.)
- Attach panel (3), (4) and (5) to panel (1).
- Insert all hardware A2 into A1.
- Rotate all A1 until tight.
- Apply A3 onto all A1.
(Repeat 6 times.)
OR
HARDWARE F
SCREWDRIVER
REQUIRED
* In this step hardware A1, A2 and B are pre-inserted.
x6
PRESS
ROTATE
Section View
x6
A3
A1 A2
3
5
4
6
6
1
2
13
5
4
6
6
3
5
4
6
6
1
x40
HIT
G
8
4
2
212
11
12
GHDSV-1402

STEP 9
STEP 11 STEP 12
MODEL : ASSEMBLY INSTRUCTIONS PAGE: /5
4
Insert hardware I into mounting positions on panel (3), (4) and (5) by hand.
(Repeat 24 times.)
x24 PRESS
I
- Assemble the panel (7) into between
panel (3) and (5).
(Repeat 3 times.)
- Assemble the panel (7) into between
panel (4) and (5).
(Repeat 3 times.)
* In this step hardware I are pre-inserted.
- Fix hardware H onto panel (9) and (10) by using hardware D.
(Repeat 8 times.)
- Fix hardware J onto two panel (9) and (10) by using hardware E.
(Repeat 4 times.)
SCREWDRIVER
REQUIRED - Fix hardware H into panel (3) and (4) by using hardware D.
(Repeat 4 times.)
- Tighten or loosen the screw to adjust position of
panel (9) and (10).
(Do only when needed.)
SCREWDRIVER
REQUIRED
* In this step hardware H have been assembled in panel (9) and (10).
ADJUST
ADJUST
H
HROTATE
x16 D
H
9
10
4
3
5
1
STEP 10
4
5
3
1
2
77
7
7
77
3
4
5
1
2
x8
ROTATE
HD
ROTATE
E
x4
910
J
J
H
H
H
H
GHDSV-1402

STEP 13
STEP 15 STEP 16
MODEL : ASSEMBLY INSTRUCTIONS PAGE: /5
5
STEP 14
Assemble hardware N1 into panel (1) and (8)
by using hardware N2.
(Repeat 2 times.)
SCREWDRIVER
REQUIRED
ROTATE x2
N1
N3
N4
ROTATE x2
N1
N2
- Mark and use the power drill
to drill a hole on the wall.
- Hit hardware N3 into the wall.
(Repeat 2 times.)
HAMMER
REQUIRED
POWER
DRILL
REQUIRED
HIT
x2
N3
- Assemble hardware N1 to N3 by using hardware N4.
(Repeat 2 times.)
SCREWDRIVER
REQUIRED - Connect two of the hardware N1 by using hardware N5.
- Tighten the hardware N5.
(Repeat 2 times.)
TIGHTEN
CONNECT x2
N1
N1
N5
x2
N1
N1
N5
83
1
4
9
10
1
4
9
10
1
4
9
10
1
GHDSV-1402