Glasdon RETRIEVER CITY Manual

RETRIEVER CITY™
DOG WASTE STATION
INSTRUCTIONS LEAFLET
NOTE: ENSURE ALL RELEVANT PERSONNEL READ THE POINTS LISTED BELOW AND THAT A COPY IS PASSED TO
STAFF INVOLVED WITH THE INSTALLATION.
OPENING AND CLOSING
USING THE SACK RETENTION
Fig. A
Fig.B
Fig. C Fig. D
1. Insert key in to the keyhole (Fig. A) and place left hand in
the sack dispenser holes. Turn the key anti-clockwise until
it stops.
2. Using the sack dispenser as a handle lift the door to allow
it to swing open (Fig. B)
3. To close simply slam the door shut, ensuring the door
drops into position.
1. Lift the sack band (Fig. C) and drop a sack between it and
the back of the unit.
2. Loop the sack over the two bungs at the back of the unit
and over the sack band.
3. Push the sack band down into place to secure the sack.
4. Reverse this process to release and replace the sacks.

FILLING THE SACK DISPENSER
INSTALLATION: GROUND FIXING
Fig. F
Fig. E
Fig. G
Fig. H
1. To load the dispenser pull the arm back (Fig. E)
and place sacks centrally over the rounded end.
2. Allow the arm to swing back into place, ensuring
that the sacks stay looped over it (Fig. F).
If using Glasdon fixings please follow the
instructions supplied with the fixing kit.
Kits containing 4 bolts should be placed in the
holes shown in Fig H.
If using non Glasdon fixings ensure that 50mm
diameter washers are used on the base of the
unit.
We strongly recommend that the unit is always
installed into a concrete slab unless soft earth
installation method is being used. Black top
or block paved areas are not suitable fixing
surfaces.
P. 2
NOTE: IF USING GLASDON SACKS TEAR THE CENTRAL
HOLE OUT OF THE PACK AND ENSURE THAT THIS SIDE
OF THE PACK FACES OUT TO ALLOW USERS ACCESS TO
THE SACKS (SEE FIG. F).

INSTALLATION: POST FIXING
Fig. J ITEM 1
ITEM 2
ITEM 3
ITEM 3
Fig. K
Fig. I ITEM 1
1. Using a ‘C’ Bracket (ITEM 1) as a guide, mark
4 holes to be drilled in the back of the unit, as
shown in Fig.I.
2. Drill the 4 marked holes right through with an
11mm drill bit.
3. Insert a Sleeve (ITEM 2), a Washer (ITEM 3)
and a Screw (ITEM 4) onto each hole.
4. Tighten the screws in to the C Brackets with
the 5mm Allen Key (Fig.J).
Banding can now be passed through the C
Brackets to attach the unit onto an existing post
(Fig.K).
If using Tespa or Tamtorque banding from
Glasdon please follow the Instructions supplied
with the kit. If non Glasdon banding is used
follow the manufacturers instructions.
P. 3
HARDWARE:
Item 1 - ‘C’ Bracket x2
Item 2 - Steel Sleeve x4
Item 3 - M8 x 20mm Washer x4
Item 4 - M8 Screw x4
TOOLS REQUIRED:
Pen/Scribe
Hand Drill
11mm Drill Bit
5mm Allen Key

AND RETRIEVER CITY ARE TRADEMARKS OF GLASDON GROUP OR ITS
SUBSIDIARIES IN THE U.K. AND OTHER COUNTRIES
Issue 1 Feb. 2004 Stock no. C000/0356
©Copyright August 2011
Glasdon, Inc. reserves the right to alter specifications without prior notice. HA182/99
IA planned maintenance schedule of regular inspection is recommended,
replacing components as necessary.
IReplacement components are available direct from GLASDON, Inc.
IGLASDON, Inc. cannot be held responsible for claims arising from
incorrect installation, unauthorized modifications or misuse of the
product.
INSTALLATION: WALL MOUNTING
Fig. L
Fig. N
Fig. M
1. Drill through the 4 points in circular recesses in the
back internal wall of the unit as shown in Fig.L.
2. Hold the unit against the wall at the desired height
and mark the 4 off hole positions.
3. Drill the 4 marked holes with the M6 Drill Bit (Fig.M).
4. Remove any dust or debris from the 4 holes.
5. Insert bolts (ITEM 1), sleeves (ITEM 2) and washers
(Item 3) through the unit and into the wall (Fig.N).
apply pressure and screw into the wall with a 12mm
wrench. Tighten to 25Nm.
HARDWARE:
Item 1 - M8 x 100mm Bolt x4
Item 2 - Steel Sleeve x4
Item 3 - M8 x 20mm Washer x4
TOOLS REQUIRED:
M6 x 120mm Masonry Drill Bit
Hand Drill
12mm Torque Wrench
NOTE: SUITABLE FOR USE IN CONCRETE, BRICK, BLOCK AND STONE WALLS. ANY OTHER WALLS SHOULD BE
INDIVIDUALLY ASSESSED AND THE APPROPRIATE FIXINGS UTILIZED WITH 20MM DIAMETER WASHERS.