IRT
Connectors
Printed in U.S.A.
A76
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
© 2011 Glenair, Inc. CAGE Code A6854
www.glenair.com - www.glenair.it e-mail: info@glenair.it
A
Step 3
Electrical Test: Insulation resistance 5000 Mohm (Min).
Test Voltage: 3000 Vac according with the arrangement.
Screw the backend onto the rear of the receptacle and tighten.
Step 4
Step 5
Screw the clamp onto the backend and tighten.
IRT Series
Rectangular Multi Pole Power Connector
Wiring Instructions - Receptacle Connector - Example: Size 03
Tightening Torque
Size Value
(Nm Max)
1 30.0
2 - 3 30.0
4 35.0
5 35.0
Locazione: Errore: Nessun riferimento
File:SMC IRT.dft
3.2 0.8 max
1 / 1
Errore: Nessun riferimento
Errore: Nessun riferimento
Errore: Nessun riferimento Errore: Nessun riferimento g Errore: Nessun riferimentocm² Errore: Nessun riferimento
1:1
22/02/2222 22/02/2222 / /
CODICE CODE
Ra (µm)
SCALA SCALE
PART NUMBER
MATERIALE MATERIAL
MODIFIC.
DISEGNATO
FIRMA
0.2x45°
Max.
R 0.2
Max.
GRUPPO SERIES
ATTENZIONE:
ATTENTION:
Non sono ammessi spigoli
vivi e bave di lavorazione.
No sharp edges or burrs allowed.
Tolleranze generali
General tolerances
ISO 2768 - fH
AREA
DESCRIZIONE DESCRIPTION
Spigoli interni / esterni
privi di indicazione
Inner / outer edges without
specific indication
DRAWN
CONTROLLATO
CHECKED
APPROVATO
APPROVED
SIGNATURE
DATA
DATE
REV.
FOGLIO
SHEET
1234567
PESO
8
>
≤
≤
>
≤
>
≤
≤
>
≤
>
≤
THIS COPYRIGHTED DOCUMENT IS THE PROPERTY OF GLENAIR, INC. AND IS FURNISHED ON THE CONDITION THAT IT IS NOT TO BE DISCLOSED, REPRODUCED IN WHOLE
OR IN PART, OR USED TO SOLICIT QUOTATIONS FROM COMPETITIVE SOURCES, OR USED FOR MANUFACTURE BY ANYONE OTHER THAN GLENAIR, INC. WITHOUT WRITTEN
PERMISSION FROM GLENAIR, INC. THE INFORMATION HEREIN HAS BEEN DEVELOPED AT GLENAIR'S EXPENSE AND MAY BE USED FOR ENGINEERING EVALUATION AND
INCORPORATION INTO TECHNICAL SPECIFICATIONS AND OTHER DOCUMENTS WHICH SPECIFY PROCUREMENT OF PRODUCTS FROM GLENAIR, INC.
3.1 7
A
D
E
B
C
A
B
C
D
E
1 - 2 - 3 9 2
4 - 5
1
2 - 3 30 30
4
SIZE 1-2-3 8 29
SIZE 4 18 45
Locazione: Errore: Nessun riferimento
File:SMC IRT.dft
3.2 0.8 max
1 / 1
Errore: Nessun riferimento
Errore: Nessun riferimento
Errore: Nessun riferimento Errore: Nessun riferimento g Errore: Nessun riferimentocm² Errore: Nessun riferimento
1:1
22/02/2222 22/02/2222 / /
CODICE
CODE
Ra (µm)
SCALA
SCALE
PART NUMBER
MATERIALE
MATERIAL
MODIFIC.
DISEGNATO
FIRMA
0.2x45°
Max.
R 0.2
Max.
GRUPPO
SERIES
ATTENZIONE:
ATTENTION:
Non sono ammessi spigoli
vivi e bave di lavorazione
.
No sharp edges or burrs allowed.
Tolleranze generali
General tolerances
ISO 2768 - fH
AREA
DESCRIZIONE
DESCRIPTION
Spigoli interni / esterni
privi di indicazione
Inner / outer edges without
specific indication
DRAWN
CONTROLLATO
CHECKED
APPROVATO
APPROVED
SIGNATURE
DATA
DATE
REV.
FOGLIO
SHEET
1234567
PESO
8
>
≤
≤
>
≤
>
≤
≤
>
≤
>
≤
THIS COPYRIGHTED DOCUMENT IS THE PROPERTY OF GLENAIR, INC. AND IS FURNISHED ON THE CONDITION THAT IT IS NOT TO BE DISCLOSED, REPRODUCED IN WHOLE
OR IN PART, OR USED TO SOLICIT QUOTATIONS FROM COMPETITIVE SOURCES, OR USED FOR MANUFACTURE BY ANYONE OTHER THAN GLENAIR, INC. WITHOUT WRITTEN
PERMISSION FROM GLENAIR, INC. THE INFORMATION HEREIN HAS BEEN DEVELOPED AT GLENAIR'S EXPENSE AND MAY BE USED FOR ENGINEERING EVALUATION AND
INCORPORATION INTO TECHNICAL SPECIFICATIONS AND OTHER DOCUMENTS WHICH SPECIFY PROCUREMENT OF PRODUCTS FROM GLENAIR, INC.
3.1 7
A
D
E
B
C
A
B
C
D
E
1 - 2 - 3 9 2
4 - 5
1
2 - 3 30 30
4
SIZE 1-2-3 8 29
SIZE 4 18 45
Tightening Torque
Size Value
(Nm Max)
1 9.0
2 - 3 9.0
4 - 5 13.0
Tightening Torque
Size Value
(Nm Max)
1 8.0
2 - 3 8.0
4 - 5 18.0
Locazione: Errore: Nessun riferimento
File:SMC IRT.dft
3.2 0.8 max
1 / 1
Errore: Nessun riferimento
Errore: Nessun riferimento
Errore: Nessun riferimento Errore: Nessun riferimento g Errore: Nessun riferimentocm² Errore: Nessun riferimento
1:1
22/02/2222 22/02/2222 / /
CODICE
CODE
Ra (µm)
SCALA
SCALE
PART NUMBER
MATERIALE
MATERIAL
MODIFIC.
DISEGNATO
FIRMA
0.2x45°
Max.
R 0.2
Max.
GRUPPO
SERIES
ATTENZIONE:
ATTENTION:
Non sono ammessi spigoli
vivi e bave di lavorazione
.
No sharp edges or burrs allowed.
Tolleranze generali
General tolerances
ISO 2768 - fH
AREA
DESCRIZIONE
DESCRIPTION
Spigoli interni / esterni
privi di indicazione
Inner / outer edges without
specific indication
DRAWN
CONTROLLATO
CHECKED
APPROVATO
APPROVED
SIGNATURE
DATA
DATE
REV.
FOGLIO
SHEET
1234567
PESO
8
>
≤
≤
>
≤
>
≤
≤
>
≤
>
≤
THIS COPYRIGHTED DOCUMENT IS THE PROPERTY OF GLENAIR, INC. AND IS FURNISHED ON THE CONDITION THAT IT IS NOT TO BE DISCLOSED, REPRODUCED IN WHOLE
OR IN PART, OR USED TO SOLICIT QUOTATIONS FROM COMPETITIVE SOURCES, OR USED FOR MANUFACTURE BY ANYONE OTHER THAN GLENAIR, INC. WITHOUT WRITTEN
PERMISSION FROM GLENAIR, INC. THE INFORMATION HEREIN HAS BEEN DEVELOPED AT GLENAIR'S EXPENSE AND MAY BE USED FOR ENGINEERING EVALUATION AND
INCORPORATION INTO TECHNICAL SPECIFICATIONS AND OTHER DOCUMENTS WHICH SPECIFY PROCUREMENT OF PRODUCTS FROM GLENAIR, INC.
3.1 7
A
B
C
A
B
C
D
E
1 - 2 - 3 9 2
4 - 5
1
2 - 3 30 30
4
SIZE 1-2-3 8 29
SIZE 4 18 45
Put the front insert (2) into the body. Insert the contact (3) crimped into the front insert (2).
Install the rear insert (4).
Locazione: Errore: Nessun riferimento
File:SMC IRT.dft
3.2 0.8 max
1 / 1
Errore: Nessun riferimento
Errore: Nessun riferimento
Errore: Nessun riferimento Errore: Nessun riferimento g Errore: Nessun riferimentocm² Errore: Nessun riferimento
1:1
22/02/2222 22/02/2222 / /
CODICE
CODE
Ra (µm)
SCALA
SCALE
PART NUMBER
MATERIALE
MATERIAL
MODIFIC.
DISEGNATO
FIRMA
0.2x45°
Max.
R 0.2
Max.
GRUPPO
SERIES
ATTENZIONE:
ATTENTION:
Non sono ammessi spigoli
vivi e bave di lavorazione
.
No sharp edges or burrs allowed.
Tolleranze generali
General tolerances
ISO 2768 - fH
AREA
DESCRIZIONE
DESCRIPTION
Spigoli interni / esterni
privi di indicazione
Inner / outer edges without
specific indication
DRAWN
CONTROLLATO
CHECKED
APPROVATO
APPROVED
SIGNATURE
DATA
DATE
REV.
FOGLIO
SHEET
1234567
PESO
8
>
≤
≤
>
≤
>
≤
≤
>
≤
>
≤
THIS COPYRIGHTED DOCUMENT IS THE PROPERTY OF GLENAIR, INC. AND IS FURNISHED ON THE CONDITION THAT IT IS NOT TO BE DISCLOSED, REPRODUCED IN WHOLE
OR IN PART, OR USED TO SOLICIT QUOTATIONS FROM COMPETITIVE SOURCES, OR USED FOR MANUFACTURE BY ANYONE OTHER THAN GLENAIR, INC. WITHOUT WRITTEN
PERMISSION FROM GLENAIR, INC. THE INFORMATION HEREIN HAS BEEN DEVELOPED AT GLENAIR'S EXPENSE AND MAY BE USED FOR ENGINEERING EVALUATION AND
INCORPORATION INTO TECHNICAL SPECIFICATIONS AND OTHER DOCUMENTS WHICH SPECIFY PROCUREMENT OF PRODUCTS FROM GLENAIR, INC.
3.1 7
A
D
E
B
C
A
B
C
D
E
1 - 2 - 3 9 2
4 - 5
1
2 - 3 30 30
4
SIZE 1-2-3 8 29
SIZE 4 18 45
