GLG Pastello Minibeam MKII User manual

GLG
L
I
G
H
T
I
N
G
E
Q
U
I
P
M
E
N
T
www.goedlichtengeluid.nl
[e-mail]
1
USER M ANUA L
Pastello Minibeam MKII

GLG
L
I
G
H
T
I
N
G
E
Q
U
I
P
M
E
N
T
www.goedlichtengeluid.nl
[e-mail]
2
CON TE N T S
1. General information 2
2. Safety instructions 3
3. Trait and skill specifications 4
4. Operation panel 6
5. Dimensional drawings 6
6. Photometric data 7
7. Mounting and Installation 7
8. P owe r supply and Signal connection 9
9. Display menu 11
10. DMX traits 18
11. Circuit connecting diagram 22
12. Trouble dispose 23
13. Cleaning and Maintenance 24
14. Duty ex on e r at ive and Copyright protection 24

GLG
L
I
G
H
T
I
N
G
E
Q
U
I
P
M
E
N
T
www.goedlichtengeluid.nl
[e-mail]
3
1 . GENERAL IN FOR M A T IO N
INTRODUCTION: Congratulations, you have just purchased one of the
most innovative and reliable LED fixtures on the market today. Our
company has been designed to perform reliably for years when the
guidelines in this booklet are followed. Please read and understand the
instructions in this manual carefully and thoroughly before attempting to
operate this unit. These instructions contain important information
regarding safety during use and maintenance.
Notice: As part of our ongoing commitment to continuous products
update, company will keep the right to improve this
products, the information in this menu may be changed in
the future, the company reserve the right to change the
data without any advises.
UNPACKING: Thank you for purchasing our company products. Every
product has been thoroughly tested and has been shipped in perfect
operating condition. Carefully check the shipping carton for damage that
may have occurred during shipping. If the carton appears to be damaged,
carefully inspect your fixture for damage and be sure all accessories
necessary to operate the fixture have arrived intact. In the event damage
has been found or parts are missing, please contact our customer support
team for further instructions. Inside the box you should find: the fixture,
a DMX XLR cable, a power cable, and this user manual.
Please do not discard the shipping carton in the trash. Please recycle
whenever possible.

GLG
L
I
G
H
T
I
N
G
E
Q
U
I
P
M
E
N
T
www.goedlichtengeluid.nl
[e-mail]
4
2 . SAFETY IN S TR U CT IO NS
Notice: To guarantee proper and consistent operation, it is
important to follow the guidelines in this manual. Our
company will not accept responsibility for damages
resulting from the misuse of this fixture due to the
disregard of the information printed in this manual.
●1. In order to ensure the light could operate normally, the ambient
temperature couldn't be higher than 38℃ and no lower than- 2℃.
●2. Under normal condition, the highest sectional surface temperature
may be up to 60 ℃.
● 3.These projectors are designed depends on the electric shock
protection, the projector should be connected with the power supply
system which connected ground enough. The projector's ground
cable should be connected with the ground cable of the power
supply system as well. The ground mark of the light metal cover
should be connecting with the installation bricked steadily.
●4. Don't use the power cable when the insulation is damaged.
It must be the manufacturer or distributor or the professional person
to change the damaged power cable in order to avoid any
dangerous.
●5.Please check the voltage, frequency data of power supply system is
suitable for the mentioned on the projector. Please do avoid the
different voltage between them and burn the projector.
●6.Do not attempt to operate this fixture if the power cord has become
damaged or frayed.
●7.Never open this fixture while in use.
●8.Never look directly into the light source. You risk injury to your
retina, which may induce blindness.
●9.Please be aware that damages caused by modifications to the device
are not subject to warranty.

GLG
L
I
G
H
T
I
N
G
E
Q
U
I
P
M
E
N
T
www.goedlichtengeluid.nl
[e-mail]
5
3 . PERFORMANCE TRAIT AND SKILL S PEC I F I C A T I O NS
◎ Voltage：AC100~240V 50/60Hz.
◎ Power：118W.
◎ LED chip：10W，RGBW 4 in 1 LED chip.
◎ LED QTY：7PCS.
◎ LED life：50000H.
◎ Lens degree：standard 8°.
◎ Beam angle:12°.
◎ Color: RGBW macro color system.
◎ Strobe:1-30 times/ second electronic strobe and random strobe.
◎ Dimmer ：65536 class dimmer.
◎ Pan/Tilt ： Pan ：540° times /1.5 seconds Tilt：180°/0.5 seconds.
◎ Control Mode: DMX512, RDM, Stand-alone mode ,Voice Control
mode , Mater-Slave mode , Wireless DMX512.
◎ Channel: Standard Channel : 9 , Extend Channel : 15.
◎ Display Menu:
1. 2.4 inches TFT touch screen, Chinese and English two version
language.
2, Display board can record device’s using time , show device’s
temperature, channel data and software version .
3, Edit the procedure

GLG
L
I
G
H
T
I
N
G
E
Q
U
I
P
M
E
N
T
www.goedlichtengeluid.nl
[e-mail]
6
◎ Other feature :
1.Extend IP address function , each IP address maximum can set 64
ID
2.Support DMX signal priority identification, when lose the signal
it would be turn into Black , default scene , Automatic function
etc according to your set.
3.Remote control function: control the procedure, speed etc function
by the remote controller when the product under the condition
without signal.
4.software upgrade : upgrade software by XRL cable.
◎ Outlooking: adopt ABS anti-fire plastic.
◎ Carton size : 270×260×350MM.
◎ N.W.: 3.8KG G.W.: 5.7KG
◎ Light size:226×268MM

GLG
L
I
G
H
T
I
N
G
E
Q
U
I
P
M
E
N
T
www.goedlichtengeluid.nl
[e-mail]
7
4 . OPERATION P AN EL
5 . DIMENSIONAL D R A W I N GS

GLG
L
I
G
H
T
I
N
G
E
Q
U
I
P
M
E
N
T
www.goedlichtengeluid.nl
[e-mail]
8
6 . PHOTOMETRIC DA T A
7 . MOUNTING AND I NS T A LL A TI O N
C au t i on s :
For added protection mount the fixtures in areas outside walking
paths, seating areas, and away from areas were unauthorized personnel
might reach the fixture. Before mounting the fixture to any surface, make
sure that the installation area can hold a minimum point load of 10 times
the device's weight. Fixture installation must always be secured with a
secondary safety attachment, such as an appropriate safety cable. To
avoid injury, never stand directly below the device when mounting,
removing, or servicing the fixture.
Mounting p oi n t s :
Overhead mounting requires extensive experience, including
amongst others calculating working load limits, a fine knowledge of the
installation material being used, and periodic safety inspection of all
installation material and the fixture. If you lack these qualifications, do
not attempt the installation yourself. Improper installation can result in
bodily injury. Be sure to complete all rigging and installation procedures
before connecting the main power cord to the appropriate wall outlet.

GLG
L
I
G
H
T
I
N
G
E
Q
U
I
P
M
E
N
T
www.goedlichtengeluid.nl
[e-mail]
9
Mou n t i n g
Our company is fully operational in any mounting position, hanging
upside-down, side mounted, or set on a flat level surface, etc. Be sure this
fixture is kept at least 0.5m (about 1.6feet) away from any flammable
materials (decoration etc.).
When clamp mounting; always use and install the supplied safety
cable as an added safety measure to prevent accidental damage in the event
of a clamp failure. See the image below.

GLG
L
I
G
H
T
I
N
G
E
Q
U
I
P
M
E
N
T
www.goedlichtengeluid.nl
[e-mail]
10
8 . POWER SUPPLY AND SIGNAL C O NN ECT I O N
1. P owe r s upp ly
Use the professional plug to connect the projectorand main power
supply. Please pay attention to the voltage, frequency the same as the
mentioned on the projector. Suggest each light hasseparately switched of
the power supply so that could turn on or turn oeach projector
desultorily.
2. Signal c
on n ec t i on
Please use the round 3/5-pin XLR plugs &sockets oered by menu
facture to connect the rst projector's output tothe second projector'
input and connect the second projector's output tothe third device's input.
And in the same way for the rest, eventually connect the last device's
output, all the devices are together as the following gure.
The devices’ control signal output or input by using the 3/5-pin XLR pug
and socket. If need to long then the communicationcable, please make
sure the both side of 3/5-pin plug is one to one. (one to one, two to two,
three to three). Otherwise, the communication cablewill be interrupted.
The communicate cable is 2-pin shielded cable 75
Resistance with each core is at least a 0.5mm diameter. (Caution: All the
inside leading wire of 3/5-pin XLR plug couldn't touch each other or
plinth).
Recommend to use the DMX signal terminator for theinstallation to
avoid the electronic noise damage the digitalcontrol signal. Simply

GLG
L
I
G
H
T
I
N
G
E
Q
U
I
P
M
E
N
T
www.goedlichtengeluid.nl
[e-mail]
11
speaking, DMX terminator is an XLR connector with a 1201/2w resistor
connected across pin 2 and 3.Which is then pluggedinto the output
socket on the last projector in the chain. Refer tothe connection as
above:(Picture ).We suggest using the DMX signal distributor when the
distance of the lights over 15meter,In case of eect the light
communication because of the signal feeble.
3. Light p owe r c on n ec t i on :
After doing the above operation and making sure allthe devices had been
installed with natural operate, press the powerswitch to check whether
everything is working normally.

GLG
L
I
G
H
T
I
N
G
E
Q
U
I
P
M
E
N
T
www.goedlichtengeluid.nl
[e-mail]
12
9 . DISPLAY M EN U
Ⅰ Menu Ⅱ Menu Ⅲ Menu
R emark
SETTING
DMX A d dress 001 - 512
Fixture ID 000 - 064
Channel mode
S tandard （ 9CH ）
D efault
E xtend ed （ 15CH
）
DMX input mode
Wired input D efault
Wireless input
Reset wireless
DMX function
Hold
Black
D scene
Program 1
Program 2
Program 3
Program 4
Program 5
Program 6
Program 7
Program 8
Slave - Master Slave
mode
Master mode
Music control Close
Open
Exit

GLG
L
I
G
H
T
I
N
G
E
Q
U
I
P
M
E
N
T
www.goedlichtengeluid.nl
[e-mail]
12
Ⅰ Menu Ⅱ Menu Ⅲ Menu
R emark
INFO
Fixture t imes
Power on t ime ****H
Lamp on t ime ****H
Fixture
t emperatures
LAMP_TEM ***℃
RDM UID
3888:********
DMX l ive
1 Dimmer 0 - 255
2 Dimmer fine 0 - 255
3 Shutter 0 - 255
4 Red 0 - 255
5 Green 0 - 255
6 Blue 0 - 255
7 White 0 - 255
8 Macro colour 0 - 255
9 Pan 0 - 255
10 Pan fine 0 - 255
11 Tilt 0 - 255
12 Tilt fine 0 - 255
13 Fixture control 0 - 255
14 . Calibration 0 - 255
15 . Slave ID 0 - 255
V er sion info
LED_XY_SOFT: V *.**
LED_DPY_SOFT: V* .**
Exit

GLG
L
I
G
H
T
I
N
G
E
Q
U
I
P
M
E
N
T
www.goedlichtengeluid.nl
[e-mail]
13

GLG
L
I
G
H
T
I
N
G
E
Q
U
I
P
M
E
N
T
www.goedlichtengeluid.nl
[e-mail]
14
Ⅰ Menu Ⅱ Menu Ⅲ Menu
Ⅳ Menu Remark
PERSON
Pan/Tilt
PT swap OFF Default
ON
Pan invert OFF Default
ON
Tilt invert
OFF Default
ON
Exit
DMX reset ON
Default
OFF
Reset
System reset
Exit
Quick
closedown
Open
Close
P/T angle
limit
Close
Open
Program
on/off
Close
Open
Set p/t
angle
Pan start
Pan end
Tilt start
Tilt end
Exit

GLG
L
I
G
H
T
I
N
G
E
Q
U
I
P
M
E
N
T
www.goedlichtengeluid.nl
[e-mail]
15
Ⅰ Menu Ⅱ Menu Ⅲ Menu
Ⅳ Menu
R emark
PERSON
Display
Display
language
English ( 英文 )
D efault
C hines e （中文 )
Display sleep
Light always
2 minutes
D efault
4 minutes
6 minutes
Display
intensity
10 - 100 D efault :50
Display
rotation
Normal
D efault
Rotate 180
TFT calibration
Exit
Exit

GLG
L
I
G
H
T
I
N
G
E
Q
U
I
P
M
E
N
T
www.goedlichtengeluid.nl
[e-mail]
16
Ⅰ Menu Ⅱ Menu Ⅲ Menu
R emark
MANUAL
1 Dimmer 0 - 255
2 Dimmer fin 0 - 255
3 Shutter 0 - 255
4 Red 0 - 255
5 Green 0 - 255
6 Blue 0 - 255
7 White 0 - 255
8 Macro colo 0 - 255
9 Pan 0 - 255
10 Pan fine 0 - 255
11 . Tilt 0 - 255
12 Tilt fine 0 - 255
13 . Fixture c 0 - 255
14 . Calibrati 0 - 255
15 Slave ID 0-255
Exit

GLG
L
I
G
H
T
I
N
G
E
Q
U
I
P
M
E
N
T
www.goedlichtengeluid.nl
[e-mail]
17
Ⅰ Menu Ⅱ Menu Ⅲ Menu
Ⅳ Menu
PROGRAM
Edit program
Edit program 1
Scene 0 - 100
1 Dimmer 0 - 255
2 Dimmer fin 0 - 255
3 Shutter 0 - 255
4 Red 0 - 255
5 Green 0 - 255
6 Blue 0 - 255
7 White 0 - 255
8 Macro colo 0 - 255
9 Pan 0 - 255
10 Pan fine 0 - 255
11 Tilt 0 - 255
12 Tilt fine 0 - 255
13 . Fixture c 0 - 255
14 . Calibrati 0 - 255
15 Slave ID 0-255
Save scene
Exit
Edit program 2
Same as Edit program1
Edit program 3
Same as Edit program1
Edit program 4
Same as Edit program1
Edit program 5
Same as Edit program1
Edit program 6
Same as Edit program1
Edit program 7
Same as Edit program1
Edit program 8
Same as Edit program1
Exit

GLG
L
I
G
H
T
I
N
G
E
Q
U
I
P
M
E
N
T
www.goedlichtengeluid.nl
[e-mail]
18
Ⅰ Menu Ⅱ Menu Ⅲ Menu
Ⅳ Menu
PROGRAM
Set program
Set program 1
Start step 0-100
End step 0-100
Step time 0-255
Save
Exit
Set program 2 Same as Set program 1
Set program 3 Same as Set program 1
Set program 4 Same as Set program 1
Set program 5 Same as Set program 1
Set program 6 Same as Set program 1
Set program 7 Same as Set program 1
Set program 8 Same as Set program 1
Exit
Run Running program…
Fixed scene Scene
001-100
Exit
SERVICE
Error list
Adjust
Pan
±5 00%
Tilt
±5 00%
Exit
Factory
Factory default ****
Adjust default ****
Time clean ****
Developer ****
Machine sel. ****
Exit
Updata
****
Exit

GLG
L
I
G
H
T
I
N
G
E
Q
U
I
P
M
E
N
T
www.goedlichtengeluid.nl
[e-mail]
19
10、DMX T R A I T S
Channel
DMX
values
%
Effect
1. Dimmer
0-255 0-100
2. Dimmer fine
0-255 0-100
3. Shutter
0-9 0-3 Unused range
10-49 4-19 Light→dark
， slow→fast
50-89 20-34 Dark→light
， slow→fast
90-119 35-46 Dark→light→dark
， slow→fast
120-179 47-70 Random fast→slow strobe
180-249 71-98 In-phase, slow→fast
250-255 99-100 Unused range
4. Red 0-255 0-100
5. Green 0-255 0-100
6. Blue 0-255 0-100
7. White 0-255 0-100
8. Macro
colour
0-1 0-1 Unused range
2-254 1-99 Shadow
255 100 Unused range
9. Pan
0-255 0-100
10. Pan fine
0-255 0-100
11. Tilt
0-255 0-100
12. Tilt fine
0-255 0-100