GLG pastello zoom mkII User manual

USER
M ANUA L
Pastello Zoom MKII
www.goedlichtengeluid.nl [e-mail]

Lightsky series
GLG
L
I
G
H
T
I
N
G
E
Q
U
I
P
M
E
N
T
www.goedlichtengeluid.nl
[e-mail]
1
CON TE N T S
1. General information 2
2. Safety instructions 3
3. Trait and skill speci cations 4
4. Operation panel 5
5. Dimensional drawings 6
6. Photometric data 7
7. Mounting and Installation 8
8. P owe r supply and Signal connection 10
9. Display menu 12
10. DMX traits 21
11. Circuit connecting diagram 26
12. Trouble dispose 27
13. Cleaning and Maintenance 28
14. Duty ex on e r at ive and Copyright protection 28

GLG
L
I
G
H
T
I
N
G
E
Q
U
I
P
M
E
N
T
www.goedlichtengeluid.nl
[e-mail]
2
1 . GENERAL IN FOR M A T IO N
INTRODUCTION: Congratulations, you have just purcha sed one of the
most innovative and reliable LED xtures on the market today. Our
company has been designed to perform reliably for years when the
guidelines in this booklet are followed. Please read and understand the
instructions in this manual carefully and thoroughly before attempting to
operate this unit. These instructions contain important information
regarding safety during use and maintenance.
Notice: As part of our ongoing commitment to continuous products
update, company will keep the right to improve this
products, the information in this menu may be changed in
the future, the company reserve the right to changethe
data without any advises.
UNPACKING: Thank you for purchasing our company pro ducts. Every
product has been thoroughly tested and has been shipped in perfect
operating condition. Carefully check the shipping carton for damage that
may have occurred during shipping. If the carton appears to be damaged,
carefully inspect your xture for damage and be sure all accessories
necessary to operate the xture have arrived intact. In the event damage
has been found or parts are missing, please contactour customer support
team for further instructions. Inside the box you should nd: the xture,
a DMX XLR cable, a power cable, and this user manual.
Please do not discard the shipping carton in the trash. Please recycle
whenever possible.

GLG
L
I
G
H
T
I
N
G
E
Q
U
I
P
M
E
N
T
www.goedlichtengeluid.nl
[e-mail]
3
2 . SAFETY IN S TR U CT IO NS
Notice: To guarantee proper and consistent operation,it is
important to follow the guidelines in this manual.Our
company will not accept responsibility for damages
resulting from the misuse of this xture due to the
disregard of the information printed in this manual.
1. In order to ensure the light could operate normally, the ambient
temperature couldn't be higher than 38 and no lower than- 2 .
2. Under normal condition, the highest sectional surface temperature
may be up to 60 .
3.These projectors are designed depends on the electric shock
protection, the projector should be connected withthe power supply
system which connected ground enough. The projector's ground
cable should be connected with the ground cable of the power
supply system as well. The ground mark of the lightmetal cover
should be connecting with the installation brickedsteadily.
4. Don't use the power cable when the insulation isdamaged.
It must be the manufacturer or distributor or the professional person
to change the damaged power cable in order to avoidany
dangerous.
5.Please check the voltage, frequency data of powersupply system is
suitable for the mentioned on the projector. Pleasedo avoid the
dierent voltage between them and burn the projector.
6.Do not attempt to operate this xture if the power cord has become
damaged or frayed.
7.Never open this xture while in use.
8.Never look directly into the light source. You risk injury to your
retina, which may induce blindness.
9.Please be aware that damages caused by modications to the device
are not subject to warranty.

GLG
L
I
G
H
T
I
N
G
E
Q
U
I
P
M
E
N
T
www.goedlichtengeluid.nl
[e-mail]
4
3 . PERFORMANCE TRAIT AND SKILL S PEC I F I C A T I O NS
Voltage AC100~240V 50/60Hz.
Power 246W.
LED chip 10W RGBW 4 in 1 LED chip.
LED QTY 18PCS.
LED life 50000H.
Beam angle Zoom function min.7°,max.55°.
Color: RGBW macro color system.
Strobe 1-30 times/ second electronic strobe and random strobe.
Dimmer 65536 class dimmer.
Pan/Tilt Pan 540° times /2.0 seconds Tilt 180°/1.2 seconds.
Control Mode: DMX512, RDM, Stand-alone mode ,Voice Control
mode , Mater-Slave mode , Wireless DMX512.
Channel: Simple(10CH),Standard(16CH), Extended1(20C H),
Extended2(24CH)
Display Menu:
1. 2.4 inches TFT touch screen, Chinese and English two version
language.
2, Display board can record device’s using time , show device’s
temperature, channel data and software version .
3, Edit the procedure

Lightsky series
GLG
L
I
G
H
T
I
N
G
E
Q
U
I
P
M
E
N
T
www.goedlichtengeluid.nl
[e-mail]
5
Other feature :
1.Extend IP address function , each IP address maximum can set 64
ID
2.Support DMX signal priority identication, when lose the signal
it would be turn into Black , default scene , Automatic function
etc according to your set.
3.Remote control function: control the procedure, speed etc function
by the remote controller when the product under thecondition
without signal.
4.Software upgrade : upgrade software by XRL cable.
Outlooking: adopt ABS anti-re plastic.
Carton size : 412×287×525MM.
N.W.: 8.5KG G.W.: 11.1KG
Light size:322×242×336MM
4 . OPERATION P AN EL

GLG
L
I
G
H
T
I
N
G
E
Q
U
I
P
M
E
N
T
www.goedlichtengeluid.nl
[e-mail]
6
5 . DIMENSIONAL D R A W I N GS

GLG
L
I
G
H
T
I
N
G
E
Q
U
I
P
M
E
N
T
www.goedlichtengeluid.nl
[e-mail]
7
6 . PHOTOMETRIC DA T A

GLG
L
I
G
H
T
I
N
G
E
Q
U
I
P
M
E
N
T
www.goedlichtengeluid.nl
[e-mail]
8
7 . MOUNTING AND I NS T A LL A TI O N
C au t i on s :
For added protection mount the xtures in areas outside walking
paths, seating areas, and away from areas were unauthorized personnel
might reach the xture. Before mounting the xture to any surface, make
sure that the installation area can hold a minimumpoint load of 10 times
the device's weight. Fixture installation must always be secured with a
secondary safety attachment, such as an appropriate safety cable. To
avoid injury, never stand directly below the devicewhen mounting,
removing, or servicing the xture.
Mounting p oi n t s :
Overhead mounting requires extensive experience, including
amongst others calculating working load limits, a fine knowledge of the
installation material being used, and periodicsafety inspection of all
installation material and the xture. If you lackthese qualications, do
not attempt the installation yourself. Improper installation can result in
bodily injury. Be sure to complete all rigging andinstallation procedures
before connecting the main power cord to the appropriate wall outlet.
Mou n t i n g
Our company is fully operational in any mounting position, hanging
upside-down, side mounted, or set on a at level surface, etc. Be sure this
xture is kept at least 0.5m (about 1.6feet) awayfrom any ammable
materials (decoration etc.).
When clamp mounting; always use and install the supplied safety
cable as an added safety measure to prevent accidental damage in the event
of a clamp failure. See the image below.

GLG
L
I
G
H
T
I
N
G
E
Q
U
I
P
M
E
N
T

GLG
L
I
G
H
T
I
N
G
E
Q
U
I
P
M
E
N
T
10
8 . POWER SUPPLY AND SIGNAL C O NN ECT I O N
1. P owe r s upp ly
Use the professional plug to connect the projectorand main power
supply. Please pay attention to the voltage, frequency the same as the
mentioned on the projector. Suggest each light hasseparately switched of
the power supply so that could turn on or turn oeach projector
desultorily.
2. Signal c
on n ec t i on
Please use the round 3/5-pin XLR plugs &sockets oered by menu
facture to connect the rst projector's output tothe second projector'
input and connect the second projector's output tothe third device's input.
And in the same way for the rest, eventually connect the last device's
output, all the devices are together as the following gure.
The devices’ control signal output or input by using the 3/5-pin XLR pug
and socket. If need to long then the communicationcable, please make
sure the both side of 3/5-pin plug is one to one. (one to one, two to two,
three to three). Otherwise, the communication cablewill be interrupted.
The communicate cable is 2-pin shielded cable 75
Resistance with each core is at least a 0.5mm diameter. (Caution: All the
inside leading wire of 3/5-pin XLR plug couldn't touch each other or
plinth).
Recommend to use the DMX signal terminator for theinstallation to
avoid the electronic noise damage the digitalcontrol signal. Simply

GLG
L
I
G
H
T
I
N
G
E
Q
U
I
P
M
E
N
T
ww.goedlichtengeluid.nl
[e-mail]
11
speaking, DMX terminator is an XLR connector with a 1201/2w resistor
connected across pin 2 and 3.Which is then pluggedinto the output
socket on the last projector in the chain. Refer tothe connection as
above:(Picture ).We suggest using the DMX signal distributor when the
distance of the lights over 15meter,In case of eect the light
communication because of the signal feeble.
3. Light p owe r c on n ec t i on :
the items can't be more than 6pcs under series connection.
After doing the above operation and making sure allthe devices had
been installed with natural operate, press thepower switch to check
whether everything is working normally.

GLG
L
I
G
H
T
I
N
G
E
Q
U
I
P
M
E
N
T
ww.goedlichtengeluid.nl
[e-mail]
12
9 . DISPLAY M EN U
Menu Menu Menu
SETTING
Exit

GLG
L
I
G
H
T
I
N
G
E
Q
U
I
P
M
E
N
T
www.goedlichtengeluid.nl
[e-mail]
13
Menu Menu Menu
Remark
INFO
Fixture times Power on time ****H
Lamp on time ****H
Fixture
temperatures
LAMP_TEM ***
RDM UID 3888:********
DMX live
1. Dimmer 0-255
2. Dimmer ne 0-255
3. Shutter 0-255
4. Red-1 0-255
5. Green-1 0-255
6. Blue-1 0-255
7. White-1 0-255
8. Red-2 0-255
9. Green-2 0-255
10.Blue-2 0-255
11.White-2 0-255
12.Red-3 0-255
13.Green-3 0-255
14.Blue-3 0-255
15.White-3 0-255
16.Macro colour 0-255
17.Pan 0-255
18.Pan ne 0-255
19.Tilt 0-255
20.Tilt ne 0-255
21.Zoom 0-255

GLG
L
I
G
H
T
I
N
G
E
Q
U
I
P
M
E
N
T
www.goedlichtengeluid.nl
[e-mail]
14
Menu Menu Menu
Remark
INFO
DMX live
22.Fixture control 0-255
23.Calibration 0-255
24.Slave ID 0-255
Version info LED_XY_SOFT:V*.**
LED_DPY_SOFT:V*.**
Exit

GLG
L
I
G
H
T
I
N
G
E
Q
U
I
P
M
E
N
T
www.goedlichtengeluid.nl
[e-mail]
15
Menu Menu Menu Menu
Remark
PERSON
Pan/Tilt
P/T swap Close Default
Open
Pan invert Close Default
Open
Tilt invert
Close Default
Open
Exit
Reset
System reset
Exit
Quick
closedown
Open
Close
P/T angle
limit
Close
Open
Program
on/o
Close
Open
Set P/T
angle
Pan start
Pan end
Tilt start
Tilt end
Exit

GLG
L
I
G
H
T
I
N
G
E
Q
U
I
P
M
E
N
T
www.goedlichtengeluid.nl
[e-mail]
16
Menu Menu Menu Menu
Remark
PERSON
Display
Display
language
English( )Default
Chinese )
Display sleep
Light always
2 minutes
Default
4 minutes
6 minutes
Display
intensity
10-100
Display
rotation
Normal
Default
Rotate 180
TFT calibration
Exit
Exit

GLG
L
I
G
H
T
I
N
G
E
Q
U
I
P
M
E
N
T
www.goedlichtengeluid.nl
[e-mail]
17
Menu Menu Menu
Remark
MANUAL
1. Dimmer 0-255
2. Dimmer ne 0-255
3. Shutter 0-255
4. Red-1 0-255
5. Green-1 0-255
6. Blue-1 0-255
7. White-1 0-255
8. Red-2 0-255
9. Green-2 0-255
10.Blue-2 0-255
11.White-2 0-255
12.Red-3 0-255
13.Green-3 0-255
14.Blue-3 0-255
15.White-3 0-255
16.Macro 0-255
17.Pan 0-255
18.Pan ne 0-255
19.Tilt 0-255
20.Tilt ne 0-255
21.Zoom. 0-255
22.Fixture 0-255
23.CAL 0-255
24.Slave ID 0-255
Exit

GLG
L
I
G
H
T
I
N
G
E
Q
U
I
P
M
E
N
T
www.goedlichtengeluid.nl
[e-mail]
18
Menu Menu Menu Menu
PROGRAM
Edit
program
Edit
program 1
Scene 0-100
1. Dimmer 0-255
2. Dimmer ne 0-255
3. Shutter 0-255
4. Red-1 0-255
5. Green-1 0-255
6. Blue-1 0-255
7. White-1 0-255
8. Red-2 0-255
9. Green-2 0-255
10.Blue-2 0-255
11.White-2 0-255
12.Red-3 0-255
13.Green-3 0-255
14.Blue-3 0-255
15.White-3 0-255
16.Macro 0-255
17.Pan 0-255
18.Pan ne 0-255
19.Tilt 0-255
20.Tilt ne 0-255
21.Zoom 0-255
22.Fixture 0-255
23.CAL 0-255
24.Slave ID 0-255
Save scene
Exit

GLG
L
I
G
H
T
I
N
G
E
Q
U
I
P
M
E
N
T
www.goedlichtengeluid.nl
[e-mail]
19
Menu Menu Menu Menu
PROGRAM
Edit
program
Edit program 2
Same as Edit program1
Edit program 3
Same as Edit program1
Edit program 4
Same as Edit program1
Edit program 5
Same as Edit program1
Edit program 6
Same as Edit program1
Edit program 7
Same as Edit program1
Edit program 8
Same as Edit program1
Exit
Set
program
Set program 1
Start step 0-100
End step 0-100
Step time 0-255
Save
Exit
Set program 2 Same as Set program 1
Set program 3 Same as Set program 1
Set program 4 Same as Set program 1
Set program 5 Same as Set program 1
Set program 6 Same as Set program 1
Set program 7 Same as Set program 1
Set program 8 Same as Set program 1
Exit
Run Running
program…
Fixed
scene
Scene 0-100
Save scene
Exit
Exit