GLIDiC Sound Air SPT-7000 User manual

SB C&S.Corp.
GLIDiC Sound Air SPT-7000
SB-WS73-MRTW
manual
Bluetooth-enabled smart phones, tablets, and other Bluetooth devices with music playback
and call capabilities
Product Information
using temperature range：5℃～35℃
● Earphones body
Built-in battery: 3.7V 60mAh
Bluetooth Spec.：Version 5.0
Communication distance：about 10m（input：Class 2）*
Profile：A2DP, AVRCP, HFP, HSP
Communication distance：SBC, AAC, apt XTM
Corresponding code：SCMS-T
Number of recorded devices: up to 7 units
Dimensions：about 23（W）×19（D）×24（H）mm
＊: It different according to the environment in which it is used
● Charging case
Built-in battery : 3.7V 460mAh
Wire : micro USB (Type-B) cable
Dimensions：about 80（W）×28（D）×36（H）mm
●Charging wire
Wire: micro USB (Type-B) cable
USB (Type - A) Connector length : about 30cm
Corresponding to the machine

Action time
Music playback time / call time: about 8 hours
When using a charging case
Music playback time / call time: Approx. 20 hours charging
Time: About 1 hour for earphone, 2 hours for case
* Varies depending on the usage environment.
First use
Before using this product, be sure to read the "simple guide" and instructions. And please take
good care of it after reading.
●About the book
・The average smartphone has download screens and steps. Due to the different machines
used, please confirm in the instruction manual of your hand.
・The operation of the machine will be different depending on the OS system.
Use of the product
Log on to more machines
The product can log in 7 machines at most.
※If you want to talk or listen to music with your headphones, you need to connect the
appropriate devices.
● Login steps for logging in to more than two devices
①When the headset is standby, touch the sensor of the right headset for 5 seconds
※Made sure to operate with headphones on you ear
Touch Sensor
Right（R）
The sound of login mode started ..
※Disconnect the product from the machine being connected
②Log in and connect to the corresponding machine
Login /connect in the same order as the first. Please follow the wizard steps "register (pair)
connections" to register and connect.
③When you want to switch connected devices, do the following
The steps for switching connecting devices are as follows :
③-1. When you unlinking a device, unlink the device according to the instructions
③-2. When you want to link the device again, operate on the device to link

LED display description
●Earphone
Des
LED
charing
light on
Power on
slow flash of red light
overtime
＊
low flash of red light
logging
R
R
・・・
VVR /W light light
Login ON
3
flashes
Standby, no link）
・・・
flashes white
Standby, link）
・・・
W light 5 sec
Working
・・・
R light 4 s
collect
information
w w
2s w w ・・・
W light 2 s
Collect over
w赤
赤 赤
6 blinks
●If you are using a smartphone/phone and want to talk with your headset, check if the
hands-free setup is in progress？
The steps vary depending on the device used If you are using the Soft Bank model, please
scan the QR code below and check the steps on the “Soft Bank Selection” website.
https://www.softbankselection.jp/bt/
＊: → To delete registration information (reset)”
After entering the login mode for 3 minutes, and the
device is disconnected for 3-6 minutes, the headset will
automatically timeout and power off
● Charging case
The relationship between the charging case LED and
the electricity
● Charging case
The relationship between the charging case LED and
the electricity
electricity
LED
A little
1 LED light flashes
half
2 LED light flashes
much
3 LED light flashes

FCC Statement
Warning: Changes or modifications to this unit not expressly approved by the
party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
●Reorient or relocate the receiving antenna.
●Increase the separation between the equipment and receiver.
●Connect the equipment to an outlet on a circuit different from that to which the
receiver is connected.
●Consult the dealer or an experienced radio/TV technician for help.
Shielded cables must be used with this unit to ensure compliance with the class B FCC limits.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
●This device may not cause harmful interference
●This device must accept any interference received, including interference that may
cause undesired operation.
The device has been evaluated to meet general RF exposure requirement. The device can be
used in portable exposure condition without restriction.

IC Statement
This device complies with Industry Canada licence-exempt RSS standard(s). Operation
is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause
undesired operation of the device. Under Industry Canada regulations, this radio
transmitter may only operate using an antenna of a type and maximum (or lesser) gain
approved for the transmitter by Industry Canada. To reduce potential radio interference to
other users, the antenna type and its gain should be so chosen that the equivalent
isotropically radiated power (e.i.r.p.) is not more than that necessary for successful
communication.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut
fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour
l'émetteur par Industrie Canada. Dans le but de réduire lesrisques de brouillage
radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son
gain de sorte que la puissance isotrope rayon ée équivalente (p.i.r.e.) ne dépasse pas
l'intensité nécessaire à l'établissement d'une communication satisfaisante. Le présent
appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autoris é e aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
The device must not be co-located or operating in conjunction with any other antenna or
transmitter
The device has been evaluated to meet general RF exposure requirement. The device
can be used in portable exposure condition without restriction.
L'appareil a été évalué pour répondre aux exigences générales d'exposition aux
radiofréquences. L'appareil peut être utilisé dans un état d'exposition portable sans
restriction.

product name ：GLIDiC Sound Air SPT-7000
model NO. ：SB-WS73-MRTW
The BQB logo, MIC ID and logo are printed on the Earphones.
The product name and model number, FCC ID, IC and CE logo are printed on the charging
case.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :
(1) l'appareil nedoit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
ISEDC RF Exposure Statement:
The device compliance with RF exposure guidelines, users can obtain Canadian information on RF
exposure and compliance.
This Class B digital apparatus complies with Canadian ICES-003.
Après examen de ce matériel aux conformité aux limitesd’intensité de champ RF, les utilisateurs
peuvent sur l’exposition aux radiofréquences et la conformité and compliance d’acquérir les
informations correspondantes
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
FCC ID: 2AO2PSPT-7000-R
FCC ID: 2AO2PSPT-7000-L
IC: 24766-SPT7000R
IC: 24766-SPT7000L
CANICES-3(B)NMB-3(B)
About the product information

This product uses a lithium ion battery. Lithium-ion batteries are a valuable resource that can be
recycled. Because this product has a built-in lithium-ion battery, it cannot be thrown away as
general garbage. When handling (reusing) according to the product life, etc., please contact the
following.
●softbank customer service window
Tel: [phone] (toll free)
Business hours: 10:00 ~ 19:00 (except for specific rest days)
DC voltage
DC voltage
RECYCLING
This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE).
This means that this product must be handled pursuant to European directive 2012/19/EU in order to be
recycled or dismantled to minimize its impact on the environment.
User has the choice to give his product to a competent recycling organization or to the retailer when he
buys a new electrical or electronic equipment.
About the reuse of small rechargeable batteries