GLITZHOME GH20105 User manual

Assembly Instruction
WINE RACK

1
Explosive View
PRE-ASSEMBLY PREPARATION
WARNING: MAXIMUM LOAD NOT EXCEED 55LBS ON SHELVES.
• CAUTION: Assembly will require at least 2 adults.
•
DO NOT use power tools.To prevent serious injury or death,this product is equipped with a wall
anchoring system.Before this product can be used,the wall anchoring system must be installed as
directed in the assembly instructions.
CARE AND CLEANING:DO NOT scratch or chip the finish.DO NOT use abrasive chemicals for cleaning.
Clean with mild soap on a soft rag.Rinse and dry thoroughly.
•
•
MAINTENANCE:Check bolts/screws periodically and tighten if necessary.•
WARNING:DO NOT USE if this product become damaged,and/or components are broken ormissin.
REMINDER:Please DO NOT fully tighten all bolts until metal frame assembly is complete.
BB
C
A
E
D
D
D

2
PARTS LIST
TOP PANEL (A) WINE RACK SHELF (D)SIDE PANEL (B) FLAT SHELF (C)
Qty: 1 Qty: 2 Qty: 1 Qty: 3
REINFORCED POLE (E)
Qty: 1
ALLEN BOLT (F) BOLT LOCK (G) PHILLIPS SCREW (H) ALLEN WRENCH (I)
Qty: 20 Qty: 20 Qty: 15 Qty: 1
HARDWARE LIST
Ø15*0.9mmM6*15mm
SCREWDRIVER (J)
Qty: 1
Ø4*20mm
Qty: 1
ANTI-TIPPING STRIP (K)
5*270mm
WALL ANCHOR (L)
Qty: 1
Ø8.5*30mm Ø4*40mm
Qty: 1
PHILLIPS SCREW (M)
Qty: 2
STEEL PLATE (N)
12*12*27mm

3
STEP 2
Attach 1 pc Side Panel (B) to the Top Panel (A), the Flat Shelf (C) and 3 pcs Wine Rack
Shelves (D) by using 10 pcs Allen Bolt (F), 10 pcs Bolt Lock (G) and Allen Wrench (I).
D
B
B
STEP 1
Attach 1 pc Side Panel (B) to the Top Panel (A), the Flat Shelf (C) and 3 pcs Wine Rack
Shelves (D) by using 10 pcs Allen Bolt (F), 10 pcs Bolt Lock (G) and Allen Wrench (I).
D
D
D
BC
A
A
REQUIRED HARDWARE IN THIS STEP 1 & 2
NO. DESCRIPTION SKETCH QTY
20PCSF ALLEN BOLT
20PCS
1PC
G BOLT LOCK
I ALLEN WRENCH

4
Using 4 pcs Phillips Screws (H) and Phillips Screwdriver (J) to fix the Reinforced Pole (E) to the
Flat Shelf (C) and Bottom Wine Rack Shelves (D) .
STEP 4
STEP 3
Using 10 pcs Phillips Screws (H) and Screwdriver (J) to fix the Side Panel (B), the Top Panel (A),
the Flat Shelf (C) and 3 pcs Wine Rack Shelves (D) by two sides.
B
A
D
C
B
B
A
REQUIRED HARDWARE IN THIS STEP 3
NO. DESCRIPTION SKETCH QTY
10PCSH PHILLIPS SCREW
1PCJ SCREWDRIVER
REQUIRED HARDWARE IN THIS STEP 4
NO. DESCRIPTION SKETCH QTY
4PCSH PHILLIPS SCREW
1PCJ SCREWDRIVER

5
MJ
WALL
NK
NOT INCLUDED
WALL
L
NOT INCLUDED
WALL
STEP 5
Attach steel plate (N) to top panel (A) with
screw (H) using screwdriver. Place assembled
unit in desired position. Mark position of steel
plate (N) on wall and remove unit. Drill one
hole on the wall and then put wall anchor (L)
into the predrilled hole. Attach steel plate (N)
to wall anchor (L) with screw (M) using
screwdriver. Place unit back into position.
Attach anti tipping strip (K) to steel plates (N)
as shown.
H
K
N
PHILLIPS SCREW DRIVER 1PC
NO. DESCRIPTION SKETCH QTY
REQUIRED HARDWARE IN THIS STEP 5
2PCS
1PC
1PC
1PC
PHILLIPS SCREW Ø 4*40mmM
LWALL ANCHOR Ø 8.5*30mm
KANTI-TIPPING STRIP
N
J
STEEL PLATE
PHILLIPS SCREW Ø4*20mm
H1PC

6
STEP 6