Global Industrial 641807 User manual

User's manual Manual del usuario Manuel de l'utilisateur
Customer Service
US: 1-800-645-2986
Servicio de atención al Cliente
US: 1-800-645-2986
Service à la clientèle
Canada: 888-645-2986
Specifications:
Voltage
120V~
Frequency
60Hz
Power
1200W
Vacuum
18kPa
Effective Suction
20%
1
Model(s): 641807
Corded Wet/Dry Vacuum
8 gal.
Capacity

Corded Wet/Dry Vacuum
2
SAFETY INSTRUCTIONS
1. Do not vacuum ammable liquids, gases, or other hazards.
2. Do not step on, kink, or cut the vacuum hoses. If the hoses are damaged or
otherwise impared, cease operation of the vacuum.
3. Regularly change lter and dust bag to prevent blockage or vacuum choking.
4. Cease operation of the vacuum in the event of a blockage. Running the vacuum
for an extended duration when the hose is blocked may cause permanent
damage.
5. Do not stick hands or any other body parts in the vacuum hose.
6. Do not operate the vacuum with an overlled dust bag/tank.
7. Do not allow children to operate the vacuum.
8. Vacuum can be used to clean spills and uids, but cannot be exposed to rain or wet
conditions. Water entering a power tool will increase the risk of electric shock.
9. Grounded tools must be plugged into an outlet properly installed and grounded in
accordance with all local codes and ordinances. Never remove the grounding prong
or modify the plug in any way. Do not use adapter plugs. Check with a qualied
electrician if you are unsure if the outlet is properly grounded. If the tools should
electrically malfunction, grounding provides a low resistance path to carry electricity
away from the user.
10. Disconnect power cord before making any adjusments, maintenance, or storing the
machine.
11. Do not use vacuum if power switch does not work. Cease operation and repair switch
or replace vacuum.
12. Do not use vacuum if power cord or plug is damaged. Cease operation and repair
cord/switch or replace vacuum.
13. Do not use third party or aftermarket accessories, they may impare operation of the
sander or malfunction during normal use.
14. Maintain all labels and nameplates on the machine so that they are clearly visible and
legible .

3
Corded Wet/Dry Vacuum
PACKING LIST

4
fCorded Wet/Dry Vacuum
OPERATION INSTRUCTIONS
1. To turn vacuum on or o, use the on/o switch located at the
front of the vacuum cover. When turning vacuum on, make sure
it is properly plugged in rst while it is still o. Turn switch o
before unplugging after nishing vacuuming, or when changing
accesories.
2. To connect hose to vacuum, insert end of hose into inlet and
rotate clockwise until locked. To remove, rotate counterclockwise
and then pull.
3. To connect telescoping tube to hose, insert hose handle
into tube and rotate clockwise until tight. To remove, rotate
counterclockwise and then pull.
4. To connect oor/round brush to tube, insert bottom of tube into
brush outlet and rotate clockwise until tight. To remove, rotate
counterclockwise and then pull.
5. To use the blower, turn the on/o switch o. Insert end of hose
into blowing port, located in the front of the vacuum cover, then
turn the switch on.
6. To clear blockages in hose, reduce motor speed and press hose
into spring loaded button located on top of the cover. Increase
suction as needed to remove blockage.
7. To install/replace dust bag, open transparent inlet cover. To
install dust bag, pull back spring lock on underside of inlet cover
and slide the bag opening over the inlet pipe, then release the
spring lock. To remove a used bag, pull back spring lock and slide
the bag o the inlet pipe. Throw out used dust bag, DO NOT
reuse dirty bags.
8. To access the vacuum tank, remove the vacuum cover by
opening the two side clamps and pulling the cover up and out of
the tank.
9. To replace/clean lter, remove the vacuum cover rst to gain
access. Pull lter up to remove. Submerge lter in soapy water to
clean. Allow time to dry completely before reinstalling. If lter is
excessively used or damaged, replace with a new lter.
WARNING
DO NOT use vacuum to suck
or blow burning or ammable
material or otherwise hazardous
chemicals

10. To clean pipe connectors remove them from the vacuum. Pipe
connector ange slides out of channel. Wash connectors under
running water.
11. To adjust motor speed, turn motor speed dial located above
power switch.
12. To clean vacuum tank, remove vacuum cover and wash tank in
sink with soapy water.
MAINTENANCE
1. Avoid using the vacuum for more than 20 minutes at a time.
2. Clean the lter and tank after every use and replace the dustbag.
Do not run the vacuum with a dirty lter or full dust bag.
3. Dump any dirty water after vacuuming to prevent corrosion.
4. Dry all wet surfaces with a paper towel or dry cloth.
5. DO NOT vacuum for more than 20 minutes at a time, the motor
may overheat.
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
Plug is improperly connected Reconnect plug
Power cord is damaged Replace power cord
Outlet is not producing voltage Use different outlet
On/off switch is broken Replace on/off switch
Blockage in brush, hose, tube Remove blockages
Filter is clogged Clean or replace filter
Dust bag is full Replace dust bag
Vacuum has been running for
more than 20 minutes
Turn vacuum off for 20 minutes
until next use
Blockage in brush, hose, tube Remove blockages
Hot air coming from air outlet
Reduced suction
Motor won't start
TROUBLESHOOTING
Corded Wet/Dry Vacuum
5