Global 796000 User manual

PORTABLE
SPOT COOLER
Instruction Manual
Model 796000
PORTABLE SPOT COOLER
Model 796000

• Risk of shock.
• DO NOT use if power cord is damaged.
• DO NOT use with extension cord.
• Unplug power cord before moving cooler.
• Disconnect from power before opening.
• Risk of water leak and shock.
• DO NOT put fingers or other objects into front or rear
fan grill.
• DO NOT operate cooler without air filter in place.
• Not for outdoor use.
• DO NOT modify or add extension to air outlet duct.
• Cooler must be a minimum of 3 feet from walls or
obstructions for proper cooling operation.
• No end user serviceable parts.
• DO NOT put anything in tube.
• DO NOT block inlet or tube.
This product contains chemicals which are known to the
State of California to cause cancer, birth defects or other
reproductive harm.
WARNING
!
!
27
SPECIFICATIONS
Input Power: AC 115V
Frequency: 60Hz
Cooling Capacity: 6200 BTU/h
Current Consumption (A): High: 7.2 / Low 7.0
Consumption Watts (W): High: 810 / Low 795
Coolant: R407C
Size: 18.7” x 10.4” x 24”
Weight: 51 lbs.
Power Cord Length: 5 ft.
MAINTENANCE
FILTER CLEANING
Filter should be cleaned
periodically to remove dust
and debris. Dust and debris in
the filter will reduce airflow
and may cause the cooler to
overheat.
The filter is located on the
front of the machine and can
be removed by holding the lip
and pulling straight up until it
is out of the retaining grid.
To clean the filter use a mild
detergent and a soft cloth and
rinse with clean water.
DO NOT REPLACE filter
into holder until it is dry.
STORAGE OF UNIT
Unplug unit and drain water from condensation tank. Make sure tank is dry
before storing. Clean Filter as noted above.
Store cooler in upright position DO NOT LAY DOWN on sides. Store in a
dry location.
Reset
Button
Test
Button
Lip

4
3
2
1
PORTABLE SPOT COOLER – Model 796000
ASSEMBLY PROCEDURE AND PARTS LIST
63
5
1. Main Unit
2. Swivel Casters
3. Condensation Water Tank
4. Water Tank Cover Plate
5. Hose Elbow
6. Flexible Hose
7. Washable Filter
8. GFIC PLUG
9. Condensation Tank Full
Indicator Lamp
10. Power Switch
6
7
RUNNING THE SPOT COOLER
1. Rotate the power knob on top of the unit clockwise (to the right) to the
LOW position. To increase airflow rotate the knob clockwise (to the
right) to the HIGH position.
2. To turn off the cooler rotate the knob in the counter clock direction (to
the left) to the OFF position.
DO NOT RESTART THE COOLER FOR 3 MINUTES
AFTER YOU HAVE TURNED IT OFF.
ADJUSTING OUTPUT DUCT
1. Pipe can be rotated 360 degrees.
2. Pipe can be tilted approximately 15 degrees (4 inches).
TROUBLESHOOTING
The spot cooler has three automatic shutoffs.
1. Overheat Shutoff protection: The cooler has an overheat protection system
in the compressor that shuts off the unit if it overheats. Overheating can
be caused by Low Voltage, high ambient temperature or air outlet
blockage. These conditions can cause the condenser to overheat. Turn
cooler off and allow unit to reset before re-starting.
2. When the water condensation tank is 75 percent full it will automatically
shut off the cooler and indicator lamp will illuminate until the tank is
emptied. To restart, turn off the cooler using the power switch on the top
of the cooler. Then empty the water tank and replace into the machine. To
restart the cooler using the power knob on top of the cooler.
3. GFIC circuit on the plug has tripped. Turn the cooler off using the knob
on top of unit then press the reset button on the plug then turn the
cooler on using the knob on the top of the unit.

45
BEFORE STARTING YOUR SPOT COOLER
ALLOW COOLER TO STAND IN AN UPRIGHT
POSITION FOR AT LEAST 24 HOURS.
1. Place the cooler at least 3 feet from wall or obstruction.
2. Only place on level surface
3. Plug into a 115V outlet. Do not
use an extension cord.
4. Test the GFIC plug by
depressing the lower button on
the plug.
5. Reset GFIC plug by depressing
the RESET button.
6. Rotate power switch to LOW
position fan will start.
7. To increase air output turn
switch to HIGH position.
8
Reset
Button
Test
Button
WATER TANK
The condensation tank is
located behind a small
plastic cover. To remove
tank place your finger
into the plastic cover and
pull to remove the cover.
The tank is equipped
with an automatic shut
off valve that will turn the
cooler off once the tank
is 3/4 full and indicator
light will illuminate.
Remove the cover
exposing the tank. Slide
the tank out of the
pocket. Empty the tank.
Slide the tank back into
the pocket and replace the cover by placing the tabs on the cover onto the
slots on the face of the case and press the cover into place.
Before moving cooler at any time the condensation tank should be emptied,
to prevent water from spilling into cooler. Unplug cooler from power supply
before performing any maintenance or moving the cooler.
4
3