Global 261120 User manual

031811
OWNER’S MANUAL
IMPORTANT: READ OWNER’S MANUAL CAREFULLY
Please fill out and return your warranty card
MODEL 261120
Floor Burnisher

CONGRATULATIONS on your purchase of a Global
product. We appreciate your business and will do
everything in our power to keep you happy with your
purchase for many years to come.
Your purchase entitles you to the best protection by
one of the most comprehensive warranties in the
industry.
Thank you for purchasing a GLOBAL product.
TABLE OF CONTENTS
Safety Precautions 3
Machine Operation 4
Machine Maintenance & Storage 4
Handle Release Assembly Instructions 5
Parts Lists 6-10
Wiring Diagram 11
TABLE OF CONTENTS
2
ORDER YOUR CLEANING CHEMICALS & PADS
Visit www.globalindustrial.com Or Call 1-800-645-1232
CLEANING CHEMICALS
Floor Finish
Model 640403
(Case of 4)
PADS (Case of 5)
High Freq., Soft to
Medium Finish -
Model 261166
Low Freq., Medium
to Hard Finish -
Model 261167
Low Freq., Hard Finish -
Model 261168

This machine must be grounded! Grounding provides
the path of least resistance for electrical current. To
reduce the risk of electrical shock should the machine
malfunction, the machine has a special grounding
plug.
This machine is intended for commercial use. It is
constructed for use in an indoor environment and is
not intended for any other use.
• Use with approved accessories only
•
Use with non-approved accessories voids warranty
• DO NOT modify machine
• Modification to machine voids warranty
All operators shall read, understand and exercise the
following safety precautions:
1) Do not operate machine:
• Unless trained and authorized
• Unless you have read and understood
operators manual
• In flammable or explosive areas.
• With damaged cord or plug.
• If not in proper operating condition.
• In outdoor areas.
• In standing water.
• With the use of extension cords.
2) Before operating machine:
• Make sure all safety devices are in place and
operate properly.
3) When using machine:
• Do not run machine over cord.
• Do not pull machine by cord or plug.
• Do not pull cord around sharp edges or corners.
• Turn power switch to “off” prior to unplugging
machine.
• Do not unplug by pulling on the cord.
• Do not stretch cord.
• Do not handle plug with wet hands.
• Keep cord away from heated surfaces.
• Do not pick up burning or smoking debris such
as cigarettes, matches or hot ashes.
• Report any damages to your supervisor.
• DO NOT attempt to fix machine by yourself. All
repairs must be made by authorized
technicians.
4) Before leaving or servicing machine:
• Turn off machine.
• Unplug cord from outlet.
5) When servicing machine:
• Unplug cord from outlet.
• Use manufacturer supplied or approved
replacement parts.
• Any lifting or hoisting of machine should be
done with OSHA approved equipment and
safety precautions.
SAFETY PRECAUTIONS
3
Do not remove the ground pin under
any circumstances!
WARNING
!

OPERATION OF HIGH SPEED FLOOR BURNISHER
4
READ OPERATOR’S MANUAL
THOROUGHLY PRIOR TO
OPERATING OR SERVICING
THIS MACHINE
GENERAL USE
1. Remove any obstructions or other obstacles in the
area which is to be cleaned.
2. Place the handle in the upright position and tilt
machine back until handle rests on the floor.
3. Attach the pad to the machine by first unscrewing the
male end of the “big mouth” from the flexible pad
driver. Place the approved pad on the pad driver,
place the male end of the “big mouth” into the center
hole of the pad, and tighten the “big mouth” firmly to
the pad driver.
4. Place machine back into its upright position.
5. Plug power cord into a grounded outlet.
6. The handle height may be adjusted by lifting up the
compression handle which is located on the right
side of the handle tube about 1 foot above floor level.
Release the compression handle and adjust handle
to safe operating height, then push back down on the
compression handle to lock the handle in operating
position.
7. To start the machine, press the red safety button on
the top of the upper switch housing, and then
squeeze either of the operating triggers. (The safety
button must be depressed prior to squeezing the
operating triggers.)
8. When the machine is in operation, both hands
should be placed on the switch housing (upper
handle).
9. To stop the machine at any time, simply release the
operating trigger(s) and the machine will stop
automatically.
MAINTENANCE
To keep the machine performing well for many years,
please follow the following maintenance procedures.
1. Unplug machine as soon as you are done using it.
2. Clean the outside of the machine with a mild cleaner.
3. Check power cord for any damage. If damage is
detected, replace power cord immediately.
4. Lubricate wheels with a water resistant lubricant
once a month.
5. Check machine for loose or missing nuts and bolts,
and replace as necessary.
6. If the machine is used in a dusty environment, you
may remove the motor cover and blow the motor
clean with compressed air. This will ensure proper
ventilation, and allow the motor to run cooler.
STORAGE
1. Unplug machine from power source and wrap cord
on handle.
2. Tilt machine so the pad is not touching the floor.
3. Store machine in upright position and in a dry area.
WARNING
Be sure the machine is not plugged into an outlet.
!
WARNING
Never use an extension cord in
conjunction with the standard power cord.
!
WARNING
Always confirm that the machine is unplugged
prior to performing any maintenance or repairs.
!

HANDLE RELEASE ASSEMBLY
5
STEP 1
1- Remove nut and spacer from handle
bracket assembly.
2- Push the two handle brackets forward
so they lean against the motor.
STEP 2
1- Remove handle clamp
blocks with 5mm hex head.
2- Place handle assembly
into handle clamp blocks.
3- Re-attach the blocks to the
base with 5mm hex head.
STEP 3
1- Place cord wrap assembly (2 pieces) in place, and snug
them together with 6mm hex bolt. (Actual cord wrap faces
to the left of the machine when you are standing behind it.)
2- Assemble hardware in the following order: Spacer, left
handle bracket, nylock nut. (DO NOT overtighten nylock
nut; only tighten it enough to hold handle in place when
compression lever is in down position.)
STEP 4
1- Connect power cords together.

MODEL 261120 - HANDLE GRIP ASSEMBLY
6
PARTS LIST

DIA No. Part Number Description NO Req'd
1 VF53109 TUBE HANDLE 1
2 VF13493 SCREW, M6 x 10, HEX SOCKET 1
3 VF30013 HOOK, CABLE 1
4 VF14114 SCREW, M8 x 55, HEX 1
5 VF13517 WASHER, PLAIN, 10x20x2.5 1
6 VF13504 NUT, M10, NYLON INSERT 1
7 VF30011 CLAMP BLOCK, HANDLE 2
8 VF14053 HEX SOCKET SCREW, M6x25 4
9 VF50120 GROMMET 1
10 VF45125 CORD, HANDLE, 14/3C 1
11 VF30014 COVER, HOOK, CABLE 1
12 VF13503 NUT, M8, NYLON INSERT 1
13 VF30015 BOLT, HANDLE RELEASE 1
14 VF30018 WASHER, PLAIN, HANDLE RELEASE 2
15 VF30017 SCREW PIN, HANDLE RELEASE 1
16 VF30016 HANDLE RELEASE 1
17 VF14222 SCREW, M5x12, PH 4
18 VF13604 EXTERNAL TOOTH WASHER, 5 4
19 VF47035A LOGO 1
20 VF30101 FRONT COVER 1
21 VF48310 HANDLE GRIP 2
22 GV40218 SPRING, SAFETY BLOCK 1
23 VF46705 SAFETY BLOCK 1
24 VF30109 COVER, LEVELING HANDLE 1
25 VF13526 HEX SOCKET SCREW, M4 x 30 1
26 GT13013 NUT, M4 3
27 VF13527 EXTERNAL TOOTH WASHER, 4 1
28 VF30104 LEVER, RIGHT, SWITCH 1
29 VF14212 SCREW, M3x25, PH 2
30 VF13511 WASHER, LOCK, INTERNAL TOOTH 2
31 VF44203 SWITCH ASSY 1
32 VF99010C CIRCUIT BREAKER, 17AMPS 1
33 VV13661 SCREW, M4x12, PH 2
34 VF48309 CLAMP BLOCK, CORD, HANDLE 1
35 VF13528 EXTERNAL TOOTH WASHER, 6 2
36 VF14218 SCREW, M6x45, PH 2
37 VF14223 SCREW, M6x25, PH 2
38 VF30102 REAR COVER, HANDLE 1
39 AS22009 STRAIN RELIEF, CORD, POWER SUPPLY 1
40 VF45119 CORD, POWER SUPPLY 1
41 VF30103 LEVER, LEFT, SWITCH 1
42 VF48306 PIN 2
43 VF53111 COVER, LEVER, SOLUTION 1
44 VF45124 JUMP WIRE 1
MODEL 261120 - HANDLE GRIP ASSEMBLY
7

MODEL 261120 - BASE GROUP ASSEMBLY
8
PARTS LIST

DIA No. Part Number Description NO Req'd
1 ZD41000C MOTOR, 120V 1
2 VF53112 BRACKET, LEFT 1
3 VF53104 AXLE, TRANSPORT 1
4 VF53106 SPACER, WHEEL, TRANSPORT 1
5 VF13520 RETAINING RING, EXTERNAL, 12 2
6 VF50119 WAVING WASHER, 12 2
7 VF48202 WHEEL, 5" 2
8 VF13666 WASHER, PLAIN, 12 2
9 VF44012 SCREW, M5x12.7 2
10 ZD40225 BEARING, 6203Z 1
11 VF99926-2 CARBON BRUSH 4
12 ZD41200A SHAFT & ROTOR ASSEMBLY 1
13 ZD40226 BEARING, 6004Z 1
14 VF53103R FRONT AXLE 1
15 VF13523 SCREW, FLAT, M6X8 2
16 VA13474 SCREW, M5x16, PH 2
17 VF13474A WASHER, PLAIN, 5x16 2
18 VF13517 WASHER, PLAIN, 10 12
19 VF13518 WASHER, LOCK, 10 8
20 VF13497 SCREW, 3/8"-16, HEX 4
21 VF14009 SCREW, M10x65, HEX 1
22 VF14005 NUT, M10, HEX 1
23 VF52008 SPACER, DRIVING PULLEY 1
24 VF52009G DRIVING PULLEY 1
25 VF52021 WASHER, PLAIN, 8x30x5 2
26 VF13519 WASHER, LOCK, 8 2
27 VF14008 SCREW, 5/16"-18, HEX 1
28 ZD41313 JUMP WIRE 1
29 VF44204 RECTIFIER 1
30 VF54029 DECAL 1
31 VF99003A BIG MOUTH 1
32 VA13484 ST4x12, PH 3
33 GT13018 SCREW, M8x30 1
34 VF99024D PAD HOLDER 1
35 VF14079B VEE BELT 1
36 VF52004A DRIVEN PULLEY 1
37 VF14075 BEARING, 6004 2RS 2
MODEL 261120 - BASE GROUP PARTS LIST
9

DIA No. Part Number Description NO Req'd
38 VF52006 SPACER, BEARING 1
39 VF14003 RETAINING RING, INTERNAL, 42 2
40 VF52001 KEY, DRIVEN SHAFT 1
41 VF52005 DRIVEN SHAFT 1
42 VF14007 SCREW, M10x32, HEX 4
43 VF52007 MOUNTING PLATE, DRIVEN SHAFT 1
44 AS321203 BUMPER, FRAME 1
45 VF53101 FRAME 1
46 VF14059 CAP NUT, M10 4
47 VF14004 RETAINING RING, EXTERNAL, 19 2
48 VF50123 WASHER, 19 2
49 VF47027 WAVING WASHER, 19 2
50 VF47055 WHEEL, 160MM 2
51 VA96851 CAP, FRONT AXLE 2
52 VF53107 HEX SCREW, BRACKET 2
53 VF13514 WASHER, PLAIN, 8x16 2
54 VF53113 BRACKET, RIGHT 1
55 VF999794 PIGTAIL CORD 1
56 ZD40205 KEY, MOTOR 1
57 VF41079 LOGO 1
58 VF53110 LABEL 1
MODEL 261120 - BASE GROUP ASSEMBLY
10