Globalstar SPOT Gen4 User manual

1
SPOT GEN4TM
USER GUIDE
FPO

1
HOW SPOT WORKS
SPOT MAPPING
1. GPS satellites provide signals.
2. SPOT Gen4 determines your GPS location and sends your location and pre-programmed message to
communication satellites.
3. Communication satellites relay your message to specific satellite antennas around the world.
4. Satellite antennas and a global network route your location and message to the appropriate network.
5. Your location and messages are delivered according to your instructions via email, text message, or
emergency notification to the GEOS International Emergency Response Coordination Center.
When SPOT sends a text or email message to one of
your contacts or to GEOS International Emergency
Response Coordination Center (IERCC), it includes your
GPS coordinates and a web link (email only) to view your
location using SPOT Mapping.
GPS SATELLITE SYSTEM
1GLOBALSTAR SATELLITE 3MESSAGING SERVICES 5
SPOT GEN4
2ANTENNAS 4

2
SECTION 1: WELCOME
SPOT Gen4 gives you a critical, life-saving line of communication when you travel beyond the boundaries
of reliable cellular service. SPOT Gen4 lets family, friends, and colleagues know you are OK, or if the
unexpected should happen, sends your GPS location to emergency responders all with the push of a
button. Add this rugged, pocket-sized device to your essential gear and stay connected wherever you play
or work.
• SPOT Gen4 needs a clear view of the sky to obtain a GPS signal to provide the most accurate
location information. SPOT Gen4 is not as reliable at the bottom of a deep canyon, in a cave, or in
very dense woods.
• Orienting SPOT Gen4 so that the SPOT logo is facing up toward the sky will improve performance as
the antenna is located directly under the logo.
• In order to ensure best performance, keep the SPOT Gen4 at least 12-18 inches away from any
navigation equipment or GPS antennas.
HERE ARE A FEW IMPORTANT THINGS TO REMEMBER ABOUT YOUR SPOT GEN4
Before every adventure, test the Buttons/LED on your device while it’s turned off. Once the test has been
completed, go outside where the SPOT Gen4 has a clear view of the sky in all directions and send a
Check In message.
FOLLOW THE STEPS BELOW TO TEST THE BUTTONS/LED:
Device check: Insert fresh batteries* and then perform the LED/Button test.
NOTE: STEPS HAVE TO BE PERFORMED WITHIN A FEW SECONDS OF EACH OTHER, OR THE TEST WILL TIMEOUT. YOU
CAN START OVER IF THE TEST IS NOT COMPLETED.
1
With your SPOT Gen4 off, press & hold the Track
button followed by the Power button. Hold for
approximately 3 seconds.
e HELP and S.O.S. LEDs should turn green.
2Press the S.O.S. and Help buttons at the same
time. All LEDs should turn red.
3Press the Custom Message and Check In buttons
at the same time. All LEDs should turn green.

3
SECTION 2: GETTING STARTED
Your SPOT Gen4 requires an active SPOT subscription to communicate. To do this, simply activate your
device using the instructions outlined below.
WITH YOUR SPOT GEN4
WHAT YOU NEED
• Your SPOT Gen4
• One of these power sources:
• 4 AAA Energizer®Ultimate Lithium 8x batteries (L92); included
• 4 AAA Energizer®NiMH rechargeable batteries (NH12)
• User Guide
INSTALL THE INCLUDED BATTERIES
1. A coin or pocket knife can be used to loosen the screws to open the battery cover.
2. Write down the ESN and Authorization Code for use during service activation.
3. Install 4 AAA Energizer®Ultimate Lithium 8x batteries or NiMH rechargeable batteries.
4. Replace cover and tighten screws fully to maintain SPOT Gen4’s waterproof seal.
5. Keep your batteries installed.
CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries
according to the instructions.
To begin using SPOT Gen4, we recommend you spend a few minutes reading through this User Guide, then
visit FindMeSPOT.com to select a service plan and activate your SPOT Gen4.
BUTTON TEST LED CHART
BUTTONS
PRESSED HELP LED S.O.S. LED POWER LED GPS LED SEND LED
CUSTOM
MESSAGE
LED
TRACK
LED
CHECK IN
LED
TRACK
+ POWER GREEN GREEN N/A N/A N/A N/A N/A N/A
S.O.S. + HELP RED RED RED RED RED RED RED RED
CUSTOM
MESSAGE
+ OK
GREEN GREEN GREEN GREEN GREEN GREEN GREEN GREEN

4
AT FINDMESPOT.COM
WHAT YOU NEED
• Personal contact information
• Emergency contact information
• Valid email address
• Credit card information
• SPOT electronic serial number (ESN) and authorization code
ACCOUNT SETUP
1. Go to FindMeSPOT.com/Activate.
2. Existing SPOT customers should login to their current SPOT My Account to add their new device. New
customers will need to select: New Account Activation.
3. Follow the instructions given within the activation portal; do not skip forms or pages.
4. Choose the services you wish to add to your SPOT Gen4 and confirm your order to finish the
activation process.
SERIAL NUMBER (ESN)AND AUTHORIZATION CODE
ese codes are located inside the battery compartment of your SPOT Gen4. You will need these codes
when setting up your account on FindMeSPOT.com/Activate.
SERIAL NUMBER (ESN)
AUTHORIZATION CODE

5
SECTION 3: FUNCTIONS
MESSAGE SENDING LED
CHECK IN
S.O.S.HELP/SPOT S.O.V.
GPS LED
TRACK
POWER LED
CUSTOM MESSAGE
S.O.S.
With the push of the S.O.S. button, the 24/7
GEOS International Emergency Response
Coordination Center provides your GPS
location coordinates to local response teams
for the quickest response to your emergency.
TRACK
Track your adventures at an interval as
low as 2.5 minutes while motion-activated
tracking conserves battery life. With the new
SPOT Mapping you can view and share your
SPOT locations for a minimum of three years.
CHECK IN
Quick and easily let contacts know you’re OK.
HELP/SPOT S.O.V. (SAVE OUR VEHICLE)
Alert specific contacts that you need help in
non-life-threatening situations. Or use SPOT
S.O.V. for professional roadside assistance
services. . (Example: Flat tire, need a li.)
CUSTOM MESSAGE
Stay in touch while off the grid by using a
custom message.
POWER
Press the power button to turn SPOT Gen4
on; LEDs will illuminate. Press and hold the
power button until it blinks rapidly to turn
SPOT Gen4 off.
GPS LED
Indicates whether or not SPOT Gen4 is able
to see the GPS satellites & obtain your GPS
location.
MESSAGE SENDING LED
Indicates whether or not your most recent
message was transmitted.

6
SECTION 4: USING SPOT GEN4
POWER
You can power your SPOT Gen4 using the included 4 AAA Energizer Ultimate Lithium 8x batteries or using 4
AAA Energizer NiMH rechargeable batteries.
NOTE: e Gen4 cannot charge rechargeable batteries. e USB is only for firmware and setting updates.
To turn SPOT Gen4 on: Simply locate the Power button on the upper le corner of the device, press and hold
the button; the LEDs will illuminate green.
To turn SPOT Gen4 off: Press and hold the Power button until the Power LED blinks rapidly.
To conserve power: Your SPOT Gen4 will automatically turn off aer one hour of inactivity.
SELF TEST
SPOT Gen4 performs a self-test when you initially turn on your device. During self-test, all LEDs will blink
green in a rotating manner to indicate self-test is in progress. If all visible LEDs flash red, the SPOT self-test
has found a failure, please call Customer Relations.
If the Power and GPS LEDs blink red in unison, SPOT Gen4 has a GPS failure, but may still be able to
transmit an S.O.S. or Help/SPOT S.O.V. message without your GPS location.
INITIAL SYSTEM TEST
Perform an initial system test to evaluate your messaging system, from the operational condition of the
SPOT Gen4 to the readiness of those you’ve chosen to receive your messages.
1. Once you have set-up the message contacts for SPOT Gen4 in your SPOT My Account, go outside where
SPOT Gen4 has a clear view of the sky in all directions.
2. Turn SPOT Gen4 on - press and hold the Power button; LEDs will illuminate.
3. Press and hold the Check In button until the function LED blinks green.
4. Leave SPOT Gen4 outdoors. e GPS LED will blink green as SPOT Gen4 acquires a GPS fix. Once SPOT
Gen4 acquires your GPS location, the Message Sending LED and GPS LED will blink green in unison for
15 seconds to notify you that your message is being transmitted with your GPS location. e Message
Sending LED will continue to blink green until the message cycle is complete.
5. Verify that the message was received by your Check In contact list. You can also view your sent
messages in your account at SPOT Mapping.
SPOT TIP: Add your email or phone number as a contact for system testing
so you can hit the trail faster.

7
S.O.S.
SPOT Gen4’s S.O.S. function should only be used for critical, life-threatening situations. Pressing the S.O.S.
button sends an alert directly to GEOS International Emergency Response Coordination Center (IERCC).
GEOS notifies the appropriate emergency responders of your S.O.S. based on GPS location and personal
information. Depending on your GPS location, responders may include local police, highway patrol, the
Coast Guard, your country’s embassy or consulate, other emergency response centers, or search and
rescue teams. Sending false S.O.S. messages may subject you to liability for additional charges.
USING THE S.O.S. FUNCTION
To send an S.O.S. alert, open the protective flap then press and hold the S.O.S. button until the function LED
blinks green. e GPS LED will blink green when SPOT Gen4 sees the GPS satellites and while obtaining
your GPS location.
Once your GPS location is obtained, SPOT sends your S.O.S. message with GPS location. e GPS LED and
Message Sending LED will both blink green. e Message Sending LED continues to blink green until the
next scheduled message to notify you that your most recent message was transmitted.
If no GPS signal is found, the GPS LED will blink red. If possible, you should move to a location with a clearer
view of the sky. e first message will be sent within one minute aer activation with or without your GPS
location. For all subsequent messages, SPOT will keep looking for your GPS location for up to 4 minutes. e
S.O.S. message will send every 5 minutes (with or without GPS) until cancelled or the power source runs out.
TO CANCEL S.O.S.
Press and hold the S.O.S. button until the LED blinks red. Let SPOT Gen4 work until the S.O.S. button
stops blinking red to finish sending the cancellation message. e Message Sending LED will blink green
indicating it has sent the cancel message. Turning off your SPOT Gen4 while in S.O.S. mode DOES NOT send
an S.O.S. cancel message.
HOW SPOT PRIORITIZES S.O.S.
S.O.S. messages are the top priority for SPOT. When you send an S.O.S. message, your SPOT Gen4 stops
sending all other messages to allow for uninterrupted transmission of the S.O.S. message.
SPOT TIP: Let your emergency contacts know when you are planning a trip. When GEOS receives
an S.O.S. message, they will first call your contacts asking for pertinent details like your itinerary,
planned route, or other identifiers. is information helps GEOS in working with local authorities
to evaluate the appropriate response team needed and send rescue personnel fast.

8
HELP/SPOT S.O.V.
For non-life threatening situations, ask for help from friends and family or gain a direct line to professional
assistance providers using SPOT S.O.V. (additional service plan required). When you press Help, your
contacts will receive SMS/text or email messages with your GPS coordinates. Email messages also include
a link to view your location.
With SPOT S.O.V., roadside professional services will receive your Help message and current GPS location
to dispatch assistance. However, SPOT S.O.V. services provided by Nation Safe Drivers are only available
in the U.S., Puerto Rico, Washington, D.C. and Canada. Visit FindMeSPOT.com/SPOTSOV to learn more on
SPOT S.O.V. including pricing.
USING THE HELP FUNCTION
To send a Help message, open the protective flap then press and hold the Help button until the LED
blinks green. e GPS LED will blink green when SPOT Gen4 sees the GPS satellites and while obtaining
your GPS location.
Once your GPS location is obtained, SPOT sends your Help message with GPS location every five minutes
for one hour. e GPS LED and Message Sending LED will both blink green. e Message Sending LED
continues to blink green until the next scheduled message or until the mode ends.
If no GPS signal is found, the GPS LED will blink red. If possible, you should move to a location with a
clearer view of the sky. SPOT Gen4 will keep looking for your GPS location for up to 4 minutes. If no GPS
location is found in 4 minutes, SPOT sends your message without GPS location; the GPS LED will blink red
and the Message Sending LED will blink green in unison.
TO CANCEL
Press and hold the Help button until the Help LED blinks red. Leave SPOT Gen4 on while the Help cancel
message is sent, turning off your SPOT Gen4 DOES NOT cancel the Help message. When it is finished, the
Message Sending LED will blink green indicating it has sent the cancel message.
HOW SPOT PRIORITIZES HELP
Help/SPOT S.O.V. messages are a high priority for SPOT. Help/SPOT S.O.V. takes priority over Check In,
Custom Message and Tracking functions. Pressing the S.O.S. button takes priority over the Help/SPOT S.O.V.
message in order to ensure the S.O.S. message is sent. ere is no need to cancel any other modes to enter
into Help or S.O.S. mode.
SPOT TIP: Have a plan in place with your Help message contacts so they know what to do if
they receive a Help message from your SPOT Gen4.

9
CHECK IN AND CUSTOM MESSAGE
Let your contacts know where you are by sending a message with your GPS location.
Check In and Custom Message functions work the same way. is gives you the flexibility to send different
messages to different contacts, or tailor messages for a specific purpose. Let your contacts know you’ve
made camp for the night, reached your goal, or are doing fine. With the push of a button, your contacts
receive your pre-programmed message by text or email complete with your GPS location.
USING THE CHECK IN OR CUSTOM MESSAGE FUNCTION
Press and hold the Check In or Custom Message button until the function LED blinks green. The GPS
LED will blink green when SPOT sees the GPS satellites and will continue blinking while obtaining your
GPS location.
Once your GPS location is obtained, SPOT sends your message with GPS location. e GPS LED and
Message Sending LED will both blink green. e message is sent three times over a 20 minute period to
the SPOT network - this is to ensure maximum reliability in getting your message out. Only one message
will be sent to your contacts. e Message Sending LED continues to blink green until the next scheduled
message or until the mode ends.
If no GPS signal is found, the GPS LED will blink red. If possible, you should move to a location with a
clearer view of the sky. SPOT Gen4 will keep looking for your GPS location for up to 4 minutes. If no GPS
location is found in 4 minutes, SPOT does not send your message. To try again, simply press and hold the
function button. If the message does not send, the Message Sending LED will blink red.
Check In or Custom messages can be sent while Tracking.
TO CANCEL
You can end the transmission of a Check In or Custom Message by pressing and holding the function
button until the LED blinks red. is action does not cancel any message already transmitted.
SPOT TIP: You can pre-program your Check In and Custom Messages to send to different groups
of contacts. For example, set one message to send your spouse an ‘I Love You’ every day and the
other to brag to all your friends about how awesome your adventure is.

10
TRACKING
With SPOT Gen4, your friends and family can track your progress in near real-time using Shared Views
within SPOT Mapping, giving them a virtual breadcrumb trail of your adventure. New enhanced Tracking
options of 2 ½, 5, 10, 30, and 60 minutes allow you to choose the rate of Tracking that fits your adventure;
additional service fees may apply. Learn more at FindMeSPOT.com.
USING THE TRACKING FUNCTION
Press and hold the Track button until the function LED blinks green. e GPS LED will blink green when
SPOT Gen4 sees the GPS satellites and will continue blinking while obtaining your GPS location.
Once your GPS location is obtained, the GPS LED and Message Sending LED will both blink green
indicating that SPOT Gen4 is sending your track as a waypoint. e Message Sending LED continues to
blink green until the next scheduled message or until the mode ends.
If no GPS signal is found, the GPS LED will blink red. If possible, you should move to a location with a
clearer view of the sky. If no GPS location is found within 4 minutes, SPOT will not send this particular
waypoint. e GPS LED will blink red for approximately 15 seconds, the Message Sending LED will blink red
until SPOT Gen4 is ready to send the next waypoint. SPOT will try to obtain your GPS coordinates again at
your next scheduled track interval.
TO CANCEL
To stop sending track messages, press and hold the Track button until the LED blinks red or power off
SPOT Gen4.
MOTION-ACTIVATED TRACKING
SPOT Gen4 has a built-in vibration sensor sends tracks only when you are moving. When the device
is stationary for more than five minutes SPOT Gen4 will enter Suspended Track mode. SPOT Gen4
will automatically send one more track from your resting location. While at rest. SPOT Gen4 will not
send tracks. Tracking will automatically resume after the vibration sensor detects the unit has begun
moving again.
TRACKING SERVICES
Basic Tracking: With Basic Tracking, messages can be preset to send tracks at intervals of 5, 10, 30, or
60 minutes. SPOT Gen4 will send tracks at your chosen rate for as long as your device is turned on and
moving. Tracking doesn’t stop until you do.
Extreme Tracking Upgrade: SPOT Gen4 offers an extreme tracking upgrade. With all of the same tracking
features as Basic Tracking, Extreme Tracking has the added ability to track down to 2.5 minutes.
To set your rate of tracking, sign in to your SPOT My Account at FindMeSPOT.com and choose ‘view/edit’
SPOT Features from the My SPOT Devices tab. Please note: Making any change to the rate of tracking
requires you to update the settings.

11
SECTION 5: SYSTEM FUNCTION AND INDICATORS
SPOT MESSAGE SCHEDULE
SPOT Gen4 is designed to provide outstanding quality and reliability. For optimum reception always place
your SPOT Gen4 with the logo side up in clear view of the sky. Reception can be inhibited due to hills,
buildings, metal roofs or other obstructions so it is normal that some messages may not go through. at
is why SPOT automatically sends multiple messages in every mode, giving you excellent overall reliability.
In some modes, this means multiple attempts to send the same message, while in other modes it means
regularly updating GPS coordinates and sending a new message with the most up to date information.
GPS
e GPS LED notifies you whether or not SPOT Gen4 is able to see the GPS satellites and obtain a
GPS location.
• Green - e GPS LED blinks green if SPOT Gen4 sees the GPS satellites and is looking for/has found
your GPS location.
• Red - e GPS LED blinks red if SPOT Gen4 cannot see the GPS satellites and/or cannot find your GPS
location. If the GPS LED blinks red, you should move to a location with a clearer view of the sky.
PLACEMENT OF YOUR SPOT GEN4
e placement of your SPOT Gen4 can make a difference. For best reception, always keep the logo pointed
towards the sky (the satellite antenna is located under the logo).

12
MESSAGE INDICATORS
For all functions, SPOT Gen4 lets you know what it is doing.
GPS PERFORMANCE
SPOT Gen4 uses an advanced GPS chipset with extremely high sensitivity to give you maximum
performance. While the SPOT message transmitter is also very high quality, there may be times
when SPOT Gen4 will have a GPS signal, but the message won’t be able to reach the satellites due to
environmental blockage. Make sure that you have a clear view of the sky at all times.
INDICATOR BLINKING GREEN BLINKING RED
GPS Searching for GPS signal GPS location fix failed, move to a
new location
MESSAGE SENDING Message transmission schedule in
progress Last message was not sent
CHECK IN OR
CUSTOM MESSAGE Message sequence in progress Message sequence has been
cancelled
HELP SPOT Gen4 in Help/SPOT S.O.V.
mode
Help/SPOT S.O.V. has been
cancelled
S.O.S. S.O.S. is engaged S.O.S. has been cancelled
TRACKING SPOT Gen4 in Track mode Track sequence has been cancelled
POWER On Low battery

13
SECTION 6: CARE AND SUPPORT
BATTERY LIFE AND USAGE
For reliable performance, use AAA Energizer®Ultimate Lithium 8x batteries (L92) or NiMH rechargeable
batteries. e power LED will blink red when batteries are low. Colder conditions and extreme heat can
impact battery life. Always carry an extra set of batteries with you. Non-lithium batteries will work with
SPOT Gen4 but are not recommended for optimal performance. Test your SPOT Gen4 before each trip by
sending a Check In message to yourself.
SPOT Gen4 performance and battery life may be degraded in operating environments where the SPOT
GPS chip must take a longer time to acquire your GPS location, such as trying to send a message under
dense foliage. For optimal performance, operate your SPOT Gen4 with the logo side up in clear view of
the sky. Using non-recommended battery types may degrade the performance of your SPOT Gen4’s
message transmission.
SPOT Gen4 is designed to be rugged for outdoor use. Dropping the unit on hard surfaces (while not
recommended) should not damage it, but can cause a loss of power and may damage the batteries.
Power loss turns off your SPOT Gen4, stopping any current mode of operation. If dropped, SPOT
recommends replacing the batteries for optimal performance.
Warning – Replaceable Batteries - CAUTION: Risk of explosion if battery is replaced by an incorrect type.
Dispose of used batteries according to the instructions.
Warning – Blasting Area: To avoid interference with blasting operations, turn your SPOT Gen4 off when in a
“Blasting Area” or in areas posted “Turn off two-way radio.” Obey all signs and instructions.
Warning – Potential Explosive Atmosphere: Turn off the SPOT Gen4 when in any area with a potentially
explosive atmosphere and obey all signs and instructions.
Warning – Pacemakers: e Health Industry Manufacturers Association recommends that a minimum
separation of six (6”) inches be maintained between the SPOT Gen4 and a pacemaker to avoid potential
interference with the pacemaker.
Aircra Use Warning: Keep SPOT Gen4 at least 12 inches away from aircra navigation systems or GPS
antennas. SPOT Gen4 may interfere with the signal reception of GPS based devices, causing intermittent
loss of GPS information and momentary operational disruptions.

14
COVERAGE
SPOT works around the world, including virtually all of North America, Europe, Australia and portions of
South America, Northern Africa and Asia, as well as hundreds of thousands of square miles off-shore of
these areas. It is important that you check SPOT’s coverage for your destination before traveling. Visit
FindMeSPOT.com/Coverage to view the latest coverage map.
OPERATING CONDITIONS AND CLIMATE
Your SPOT Gen4 is designed for adventure. However, like all electronic devices, it has its limits. SPOT Gen4
relies on GPS and low earth orbit satellites to fix your location and send your messages. e transmitter
(located underneath the SPOT logo) needs to have an unobstructed view of the sky, either outdoors or in a
glass-enclosed area such as a vehicle dashboard. For safety, keep the following in mind regarding the care
and usage of SPOT Gen4:
• IP68 water resistant: Up to a depth of 2 m for up to 30 minutes
• Operating temperatures: -22 F to +140 F (-30 C to 60 C)
• Operating altitude: -328  to 21,320  (-100 m to 6,500 m)
• Humidity and Salt Fog rated
• If you exceed 700 mph (Mach 1) GPS accuracy degrades
CONTACTS
Additional charges may apply in some regions. Standard text messaging charges from your mobile phone
provider may also apply.
CLEANING
Follow these general rules when cleaning the outside of your SPOT Gen4:
• Make sure the power is OFF
• Use a damp, so, lint-free cloth and avoid excess moisture near buttons or openings
• Do not use aerosol sprays, solvents, alcohol or abrasives
• Do not attempt to open the SPOT Gen4 case
TROUBLESHOOTING
SPOT Gen4 performs a self-diagnostic test each time it is powered on. SPOT recommends that you send
and verify a Check In message before each trip. is also allows you to evaluate your entire messaging
system, from the operational condition of the SPOT Gen4 to the readiness of those on your contact list.
For more information, visit the Support section on FindMeSPOT.com.

15
LEARN MORE
Visit FindMeSPOT.com for the latest information on SPOT Gen4 and other SPOT products and services. If
you can’t find what you’re looking for, please do not hesitate to contact us.
CUSTOMER RELATIONS
Visit FindMeSPOT.com/ContactUs.
LIMITED WARRANTY
Your SPOT Gen4 has a Limited Warranty for 12 months (24 months for European Customers) from the date
of purchase against defects in materials and workmanship only. For full details regarding the Limited
Warranty and warranty claim procedures, visit SPOTwarranty.com or FindMeSPOT.com.
DECLARATION OF CONFORMITY FOR EUROPEAN CUSTOMERS
SPOT LLC declares that this SPOT Gen4 is in compliance with the essential requirements and other
relevant provisions of Directive 2014/53/EU. e declaration of conformity may be consulted at
FindMeSPOT.com/Regulatory.
EXCEPT AS PROVIDED ABOVE, THE PRODUCT IS SOLD “AS IS” WITHOUT ANY EXPRESS OR IMPLIED WARRANTIES FOR THE
PRODUCT WHATSOEVER, INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES REGARDING THE CONDITION,
DESIGN, SPECIFICATIONS, WORKMANSHIP, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCT,
OR ANY WARRANTIES THAT THE PRODUCT IS FREE FROM LATENT DEFECTS OR DEFICIENCIES, OR THAT THE PRODUCT IS
FREE FROM INFRINGEMENT OF ANY PATENT, TRADEMARK, COPYRIGHT OR PROPRIETARY RIGHT OF ANY THIRD PARTY AND
SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED.
THIS LIMITED WARRANTY PROVIDES THE SOLE AND EXCLUSIVE REMEDY FOR ANY DEFECTS IN THE PRODUCT. IN NO EVENT
SHALL WE BE LIABLE FOR ANY INDIRECT, CONSEQUENTIAL, SPECIAL, INCIDENTAL OR PUNITIVE DAMAGES, WHETHER IN
CONTRACT, TORT, NEGLIGENCE, STRICT LIABILITY OR OTHERWISE. OUR LIABILITY IS LIMITED TO THE AMOUNT YOU PAID FOR
THE PRODUCT THAT IS THE SUBJECT OF A CLAIM. THE APPLICABILITY OF THE ABOVE LIMITATIONS AND EXCLUSIONS MAY
VARY FROM STATE TO STATE, OR COUNTRY TO COUNTRY.
is device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
is device may not cause harmful interference, and (2) is device must accept any interference received,
including interference that may cause undesired operation.

16
* Transmit Frequencies: 1611.25 Mhz - 1618.75 Mhz (4 Channels)
* Max Power Out: 23.52 dBm EIRP
is equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. ese limits are designed to provide reasonable protection against harmful
interference in a residential installation.
is equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures: a) Reorient
or relocate the receiving antenna. b) Increase the separation between the equipment and receiver. c) Connect
the equipment into an outlet on a circuit different from that to which the receiver is connected. d) Consult the
dealer or an experienced radio/TV technician for help.
is device generates radio frequency energy at a low duty cycle (<1%). Transmitter on-time is dependent
on configurable operational modes with a maximum of two 1.44 second long transmissions per five minute
period. Satellite transmissions are 23.5 dBm EIRP. Based on these figures, the device has been exempted
from SAR testing.
In order to comply with FCC/ISED RF Exposure requirements, this device must be installed to provide at
least 20 cm separation from the human body at all times.

17
IE Not to be Marketed in the Republic of Ireland
RF Exposure: Per EN 62479:2010, the SPOT Gen4 spectral power density at a distance of 0.1 cm is
calculated to be 3.33 mW/cm² , which is less than the maximum allowable limit for uncontrolled exposure (
8.05 mW/cm²). If concerned about RF exposure during use, place the SPOT Gen4 anywhere it is not directly
touching your body aer functions have been activated. e RF exposure level drops off dramatically with
distance from the SPOT Gen4.
Warning: Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
is Class B digital apparatus complies with Canadian ICES-003.
is device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
is device complies with FCC Part 25.213.
is device automatically adjusts its transmission frequency according to its location and is compliant with
international regulatory requirements.
e SPOT Gen4 has been so constructed that the product complies with the requirement of Article 10(2)
as it can be operated in at least one Member State as examined and the product is compliant with Article
10(10) as it has no restrictions on putting into service in all of the EU except Ireland. e SPOT Gen4 cannot
be marketed in Ireland.

18
© 2020 SPOT LLC. For more information, visit FindMeSPOT.com.
e official language of this User Guide is English. Any translations provided are for your convenience
only. In the case of any contradiction between a translation and the English, the English version shall
take precedence.
USERG-ENG-V2
• ROHS and WEEE compliant
• Certified to FCC and CE emissions, immunity and safety regulations.
• Meets FCC part 25.213 regulations, Canada type approval, Directive (2014/53/EU) and IEC 62368
safety standard.
FindMeSPOT.com
R-2